Users Manual Part 8

ManualsBrandsChamberlain Group ManualsIndustrial & ScientificMain control/transceiver for use in Industrial HD Operators

Wiring Diagram

To protect against fire and electrocution:

•

DISCONNECT power (AC or solar and battery) BEFORE installing or

servicing operator.

For continued protection against fire:

•

Replace ONLY with fuse of same type and rating.

ACCESSORY ON POWER

24 VDC 1 A Maximum

N.C.

POWER SW

24 VDC 1 A Maximum

Jumper

LOCKS

ACCESSORY

POWER

DUAL

GATES

ENTRAPMENT

PROTECTION

LOOPS CONTROLS

EDGE SENSOR

for CLOSE cycle

SHADOW LOOP

EXIT LOOP

PHOTOELECTRIC SENSORS or EDGE SENSOR

for OPEN cycle

Shielded Twisted Pair Cable

(Primary/Secondary link to other gate operator) Ground the

shield of the cable to the chassis ground of each operator.

CONTROL BOARD

ANTENNA

OPEN and COM: Hard Open (line-of-sight)

CLOSE and COM: Hard Close (line-of-sight)

STOP and COM: Hard Stop(line-of-sight)

EXIT: Soft Open (used for exit probe, telephone entry, external exit

loop detector, or any device that would command the gate to open)

PHOTOELECTRIC SENSORS

for CLOSE cycle

POWER BOARD

APPENDIX

Summary of content (8 pages)

PAGE 1
APPENDIX Wiring Diagram To protect against fire and electrocution: • DISCONNECT power (AC or solar and battery) BEFORE installing or servicing operator. For continued protection against fire: • Replace ONLY with fuse of same type and rating. Jumper POWER BOARD N.C.
PAGE 2
APPENDIX MECHANICAL INTERLOCK (For slide version only) 12V SOLAR PANELS IN SERIES PRODUCT ID RESET SWITCH IHSL24UL: Red INSL24UL: Blue BATTERY SWITCH APS ENCODER 12V BATTERIES IN SERIES ALARM IHSL24UL BRIDGE RECTIFIER INSL24UL EXPANSION BOARD SHADOW LOOP 4 3 2 1 H L VARIANT: BAT POWER IN WARNING: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE ONLY WITH SAME TYPE & RATING FUSE FUSES 30A 32V Model LOOPDETLM POWER OUT Control function of photoelectric sensor or edge sensor for the OPEN or CLO
PAGE 3
APPENDIX Diagnostic Codes Table Some codes are saved in the code history and some are not. If a code is not saved it will briefly appear on the display as it occurs, then disappear. LiftMaster System Code 31 Installed System Informational External Entrapment Protection Inherent Entrapment Protection Meaning Control board has experienced an internal failure. Solution Disconnect all power, wait 15 seconds, then reconnect power (reboot). If issue continues, replace control board.
PAGE 4
APPENDIX Code 61 Meaning CLOSE EYE/INTERRUPT held Solution Saved Check wired input on control board; check for alignment or obstruction; squeeze and release the edge and verify main board edge LED changes; check for eye alignment or obstruction. YES Check wired input on expansion board; check for alignment or obstruction; squeeze and release the edge and verify main board edge LED changes; check for eye alignment or obstruction.
PAGE 5
Swing and Slide Gate Operator UL 325 and ASTM F2200 Site Planning Safety Checklist Please Print Name: Phone: Address: City/State/ZIP: Email: Needs Repair/Replacement Satisfactory Gate Safety Check — Simple steps to quickly determine if an End User’s gate operator is safe. UL 325 Standard Component: Result (Circle) 1. Gate Operator is approved to current UL 325 standards (check operator label) Pass / Fail 2.
PAGE 6
GETTING STARTED WITH SWING AND SLIDE GATE OPERATORS. Always design, install and maintain safe gate access systems in accordance with UL 325 & ASTM F2200 standards. entrapment zones are protected with a minimum of two independent† entrapment protection devices. • A slide gate operator will only operate with a minimum of two independent monitored entrapment protection devices installed in each direction, two in the open direction and two in the closed direction†.
PAGE 7
PAGE 8
Contact Information LiftMaster.com LiftMaster Partner Portal: Partner.LiftMaster.com/login LiftMaster Training Academy: LiftMasterTraining.com 800-528-2806 Mon-Fri 5:00 am to 6:00 pm MST 300 Windsor Drive Oak Brook, IL 60523 LiftMaster.com © 2022, The Chamberlain Group LLC.