Instructions / Assembly
Table Of Contents
- ENGLISH
- BILT Intelligent Instructions
- Contents
- Safety Symbol and Signal Word Review
- Unattended Operation
- Preparation
- Assembly
- Installation
- STEP1 Determine the Header Bracket Location
- STEP 2 Install the Header Bracket
- STEP 3 Attach the Rail to the Header Bracket
- STEP 4 Position the Garage Door Opener
- STEP 5 Hang the Garage Door Opener
- STEP 6 Attach the Emergency Release Rope and Handle
- STEP 7 Install the Door Bracket
- STEP 8 Connect the Door Arm to the Trolley
- STEP 9 Install the Door Control
- STEP 10 Wire the Door Control to the Garage Door Opener
- STEP 11 Attach the Warning Labels
- STEP 12 Install the Protector System®
- STEP 13 Wire the Safety Reversing Sensors
- STEP 14 Connect Power
- STEP 15 Align the Safety Reversing Sensors
- Adjustments
- Battery Backup
- myQ® App Control
- Camera
- Operation
- Maintenance
- Troubleshooting
- Warranty
- Contact Information
- Repair Parts
WARNING
1
3 2
4-5 6
8
7
To prevent possible SERIOUS INJURY or DEATH from electrocution:
Be sure power is NOT connected BEFORE installing door control.
Connect door control ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
Install door control within sight of garage door, out of reach of small children at a mini-
mum height of 5 feet (1.5 m) above oors, landings, steps or any other adjacent walking
surface, and away from ALL moving parts of door.
NEVER permit children to operate or play with door control push buttons or remote
control transmitters.
Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.
ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to
cross path of closing garage door.
INTRODUCTION
Older Chamberlain door controls and third party products are not compatible. Install door control
within sight of garage door, out of reach of small children at a minimum height of 5 feet (1.5 m) above
oors, landings, steps or any other adjacent walking surface, and away from ALL moving parts of
door. For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the
existing holes in the gang box.
NOTE:
Your product may look different than the illustrations.
Drywall
Anchors (2)
Screw
6-32x1” (2)
Screw
6ABx1” (2)
HARDWARE
Installation
STEP 9 Install the Door Control
1. Strip 7/16” (11 mm) of insulation from one end of the wire and separate the wires.
2. Connect one wire to each of the two screws on the back of the door control. The wires can
be connected to either screw. If your garage is pre-wired for the door control choose any two
wires to connect, note which wires are used so the correct wires are connected to the garage
door opener in a later step.
3. Mark the location of the bottom mounting hole and drill a 5/32” hole.
4. Install the bottom screw, allowing 1/8” (3 mm) to protrude from the wall.
5. Position the bottom hole of the door control over the screw and slide down into place.
6. Lift the push bar up and mark the top hole.
7. Remove the door control from the wall and drill a 5/32” hole for the top screw.
8. Position the bottom hole of the door control over the screw and slide down into place. Attach
the top screw.
7/16” (11 mm)
Wall
Drywall Anchor
Drywall Anchor
6ABx1”
6ABx1”
6-32x1”
6-32x1”
DRYWALL
DRYWALL
GANG BOX
GANG BOX
24