DOWNLOAD THE FREE APP Easy step-by-step interactive 3D instructions for this product can be found in Available on most iOS and Android Devices AFTER YOUR ASSEMBLY WITH BILT, DOWNLOAD THE myQ® APP Installation Manual Inside
www.chamberlain.com Installation Manual LED Belt Drive Garage Door Opener Models B4603T • B4643T • B4613T B6713T • B6753T FOR RESIDENTIAL USE ONLY PRE PROGRAMMED REMOTE CONTROL INCLUDED To register your garage door opener to receive updates and offers from Chamberlain, visit chamberlain. registria.com or use the icon below: 1. 2. Take a photo of the camera icon including the points ( ). Send it in by texting the photo to 71403 (US).
Contents Safety Symbol and Signal Word Review Preparation ������������������������������������������������������������������������������������������������������������������������������������������� 5 Assembly ����������������������������������������������������������������������������������������������������������������������������������������������� 9 Installation �������������������������������������������������������������������������������������������������������������������������������������������14
Preparation Check the Door Before You Connect with Your Smartphone Monitor and control your garage door from anywhere using the myQ® App. You will need a router with Wi-Fi® and a smartphone or other mobile device. Make sure your mobile device is connected to your Wi-Fi® network. Hold your mobile device in the place where your garage door opener will be installed and check the Wi-Fi® signal strength.
Preparation Tools Needed Additional Items You May Need: Survey your garage area to see if you will need any of the following items: l (2) 2X4 Pieces of wood : May be used to fasten the header bracket to the structural supports. Also used to position the garage door opener during installation and for testing the safety reversing sensors. l Support bracket and fastening hardware: Must beused if you have a finished ceiling in your garage.
Preparation Carton Inventory Save the carton and packing material until the installation and adjustment is complete. Instructions for the accessories will be attached to the accessory and are not included in this manual. The images throughout this manual arefor reference only and your product may look different. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
Preparation Hardware INSTALLATION ASSEMBLY Bolt 1/4”-20x1-3/4” Bolt Lag Screw 5/16”-9x1-5/8” (4) Threaded Shaft with Spring Trolley Nut DOOR CONTROL Self-Threading Screw 1/4”-14x5/8” (2) Hex Bolt 5/16”-18x7/8” (4) Clevis Pin 5/16”x1-1/2” Clevis Pin 5/16”x1-1/4” Clevis Pin 5/16”x1” Screw 6-32x1” (2) Master Link Wing Nut (2) Hex Screw 10-24 (2) Lock Washer 3/8” Hex Screw #8x3/8” (3) (packed with the sprocket cover) Nut 5/16”-18 (4) Nut 3/8” Drywall Anchors (2) Lock Nut 1/4”-20 Lock Washer 5/
Assembly STEP1 Assemble the Rail and Install the Trolley CAUTION Slide to stops on top and sides of “U” bracket o prevent INJURY from pinching, keep hands and fingers away from the joints while T assembling the rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has acut out “window” at the door end. The rail tab MUST be on top of the rail when assembled. 1.
Assembly STEP2 Fasten the Rail to the Motor Unit HARDWARE CAUTION Bolt 1/4”-20x1-3/4” To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener. Bolts (Mounted in the garage door opener) 1. Insert a1/4”-20 x 1-3/4” bolt into the cover protection bolt hole on the backend of the rail as shown. Tighten securely with a1/4”-20 lock nut. DO NOT overtighten. 2. Remove the bolts from the top of the motor unit. 3.
Assembly STEP 3 Install the Idler Pulley 1. 2. 3. 4. 5. 6. HARDWARE Lay the belt beside the rail, as shown. Grasp the end with the hooked trolley connector and pass approximately 12” (30 cm) of belt through the window. Keep the ribbed side toward the rail, and allow it to hang until Assembly Step 4. Remove the tape from the idler pulley. The inside center should be pre-greased. If dry, regrease to ensure proper operation. Place the idler pulley into the window as shown.
Assembly STEP 4 Install the Belt HARDWARE Threaded Shaft with Spring Trolley Nut 1. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley. 2. Hook the trolley connector into the retaining slot on the trolley as shown (Figure 1). 3. With the trolley against the screwdriver, dispense the remainder of the belt along the rail length toward the motor unit and around the sprocket (Figure 2). The sprocket teeth must engage the belt. 4.
Assembly STEP 5 Tighten the Belt STEP 6 Install the Sprocket Cover 1. By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley. Do not use any tools. Remove the screwdriver. 2. Insert a flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley. 3.
Installation IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS. 2. Install garage door opener ONLY on properly balanced and lubricated garage door. An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH. 3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener. 4.
Installation STEP1 Determine the Header Bracket Location Header Wall 2x4 To prevent possible SERIOUS INJURY or DEATH: l Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might NOT reverse when required. DO NOT install header bracket over drywall. l Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry.
Installation STEP 2 Install the Header Bracket WALL INSTALLATION You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided).
Installation STEP 4 Position the Garage Door Opener STEP 3 Attach the Rail to the Header Bracket 1. 2. 3. 4. Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way, you will need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. Position the rail bracket against the header bracket. Align the bracket holes and join with a clevis pin as shown.
Installation STEP 5 Hang the Garage Door Opener HARDWARE Nut 5/16”-18 Lag Screw 5/16”-9x1-5/8” To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing ANY brackets into masonry. Lock Washer 5/16”-18 Hex Bolt 5/16”- 18x7/8” Hanging the garage door opener will vary depending on your garage. Below are three example installations. Your installation may be different.
Installation STEP 6 Attach the Emergency Release Rope and Handle To prevent possible SERIOUS INJURY or DEATH from a falling garage door: l If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly. l NEVER use emergency release handle unless garage doorway is clear of persons and obstructions. l NEVER use handle to pull door open or closed.
Installation STEP 7 Install the Door Bracket HARDWARE CAUTION Self-Threading Screw 1/4”-14x5/8” Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit. Failure to reinforce the top section as required according to the door manufacturer may void the door warranty.
Installation Header Wall STEP 7 Install the Door Bracket (continued) 2x4 Support (Finished Ceiling) OPTION B - ONE-PIECE DOORS 1. Center the door bracket on the top of the door, in line with the header bracket as shown. 2. Mark either the left and right, or the top and bottom holes. Header Bracket Metal Doors: l Drill 3/16” pilot holes and fasten the bracket with the self-threading screws provided.
Installation HARDWARE STEP 8 Connect the Door Arm to the Trolley Installation will vary according to the garage door type. Follow the instructions which apply to your door. OPTION A - SECTIONAL DOORS Clevis Pin 5/16”x1-1/4” IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. 1. Close the door. Disconnect the trolley by pulling the emergency release handle. 2. Attach the straight door arm to the outer trolley using the clevis pin. Secure with the ring fastener. 3.
Installation STEP 8 Connect the Door Arm to the Trolley (continued) OPTION B - ONE-PIECE DOORS Straight Door Arm (Groove facing out) IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. 1. Close the door. Disconnect the trolley by pulling the emergency release handle. 2. Fasten the straight door arm and the curved door arm together to the longest possible length (with a 2 or 3 hole overlap) using the bolts, nuts, and lock washers. 3.
Installation STEP 9 Install the Door Control 1. Strip 7/16” (11 mm) of insulation from one end of the wire and separate the wires. 2. Connect one wire to each of the two screws on the back of the door control. The wires can be connected to either screw. If your garage is pre-wired for the door control choose any two wires to connect, note which wires are used so the correct wires are connected to the garage door opener in a later step. 3.
Installation STEP 10 Wire the Door Control to the Garage Door Opener STEP 11 Attach the Warning Labels 1. Run the white and red/white wire from the door control to the garage door opener. Attach the wire to the wall and ceiling with the staple (not applicable for gang box or pre-wired installations). Do not pierce the wire with the staple as this may cause a short or an open circuit. 2. Strip 7/16” (11 mm) of insulation from the end of the wire near the garage door opener. 3.
Installation STEP 12 Install the Protector System® Hex Screw 10-24 (2) HARDWARE Wing Nut (2) Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor. To prevent SERIOUS INJURY or DEATH from closing garage door: l Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be disabled. l Install the safety reversing sensor so beam is NO HIGHER than 6” (15 cm) above garage floor.
Installation STEP 12 Install the Protector System (continued) FLOOR OPTION 1. Measure the position of both sensor brackets so they will be the same distance from the wall and unobstructed. 2. Attach the bracket to the floor with concrete anchors (not provided). 3. Slide the hex screw through the sensor. 4. Attach the sensor to the bracket with the wing nut. Make sure the lens is not obstructed by the bracket. Repeat the steps with the other sensor on the opposite side of the garage door.
Installation STEP 13 Wire the Safety Reversing Sensors HARDWARE If your garage has pre-installed wiring for the safety reversing sensors, see OPTION B - PREWIRED INSTALLATION page 29. Insulated Staple (Not Shown) OPTION A - INSTALLATION WITH NO PRE-WIRING 1 1. Run the wire from both sensors to the garage door opener. Attach with staples, but DO NOT puncture the wire. 2. Separate the sensor wires and strip insulation from each end. Twist the two white wires together.
Installation STEP 13 Wire the Safety Reversing Sensors (continued) 1 Pre-installed wires OPTION B - PRE-WIRED INSTALLATION 1. Cut the sensor wires, making sure there is enough wire to reach the pre-installed wires from the wall. 2. Separate the sensor wires and strip insulation from each end. Choose two of the preinstalled wires and strip insulation from each end. Choose the same color pre-installed wires for each sensor. 3.
Installation STEP 14 Connect Power THERE ARE TWO OPTIONS FOR CONNECTING POWER: OPTION A - TYPICAL WIRING WARNING 1. Plug in the garage door opener into a grounded outlet. 2. DO NOT run garage door opener at this time. To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: l Be sure power is NOT connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection.
Installation STEP 15 Align the Safety Reversing Sensors SAFETY SENSOR TROUBLESHOOTING If either of the sensor LEDs are off, there is no power to the sensor: IMPORTANT: The safety reversing sensors MUST be connected and aligned correctly before the garage door opener will move in the down direction. When the garaged door opener has power, check the safety reversing sensors. If the sensors are aligned and wired correctly, both LEDs will glow steadily. 1.
Adjustments Introduction ONE-PIECE DOORS ONLY When setting the UP travel for a one-piece door ensure that the door does not slant backwards when fully open (UP). If the door is slanted backwards this will cause unnecessary bucking and/or jerking when the door is opening or closing. WARNING WARNING Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.
Adjustment 1 - Program the Travel 2 - Automatic Force Set Up WARNING Once both the up and down positions have been manually set, the Safety Reversing Sensors will reconnect and become operational. Then, the opener will enter a force-sensing operation by automatically moving the door open and close. The garage door opener will sound an audible and visual alert before automatically opening and closing the door.
Adjustments 4 - Test the Protector System® 3 - Test the Safety Reversal System WARNING Without a properly installed safety reversing sensor, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month.
Battery Backup STEP 1 Install the Battery STEP 2 Test the Battery MODELS B4613T, B6713T, AND B6753T Depending on the power level, the battery may need to charge before performing the test. The garage door opener must be unplugged to test the battery. 1. Open and close the door using the remote control or door control. While the motor is on, the battery status LED will either glow solid orange indicating opener is operating on battery power or will flash indicating low battery power.
myQ® App Control Connect With Your Smartphone YOU WILL NEED: l Wi-Fi enabled smartphone, tablet or laptop l l l l Broadband Internet connection Wi-Fi signal in the garage (2.4 GHz, 802.11b/g/n required), see page 5 Password for your home network (router’s main account, not guest network) myQ® serial number located on the garage door opener LED DOWNLOAD THE myQ® APP TO SET UP AN ACCOUNT AND CONNECT Open and close your door, get alerts and set schedules from anywhere.
Camera Set Up the Camera MODELS B4643T, AND B6753T LED 1. Download the myQ® App, setup an account, and connect. See page 36. 2. Follow the instructions in the app to setup and use the camera. The camera powers up when it is opened and powers down when closed. An LED on the camera indicates the status. See the camera status table. For more information on using the camera, visit support.chamberlaingroup.com.
Operation IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls. 3. ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel. 4.
Operation Motion Detecting Control Panel LOCK: Prevents remote controls from working, while still allowing activation from the door control and keyless entry. (Factory setting is OFF.) Turn ON: Press and hold the LOCK button for 2 seconds. The command LED will flash as long as the lock feature is on. Turn OFF: Press and hold the LOCK button for 2 seconds. The command LED will stop flashing and normal operation will resume. LIGHT BUTTON: Turns the garage door opener lights on or off when pressed.
Operation Remote Control and Keyless Entry PROGRAM USING THE GARAGE DOOR OPENER LEARN BUTTON 1. Locate the LEARN Button. 2. Press and immediately release the LEARN button. The LEARN LED will glow steady for 30 seconds. Within 30 seconds... 3. Remote Control: Press and hold the button on the remote control that you wish to use. Keyless Entry: Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press and hold the ENTER button.
Operation To Open the Door Manually Erase the Memory ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES 1. Press and hold the LEARN button on garage door opener until the learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any accessory you wish to use. To prevent possible SERIOUS INJURY or DEATH from a falling garage door: l If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED.
Maintenance Maintenance Schedule NOTICE: This device complies with part 15 of the FCC rules and Innovation, Science and Economic Development Canada license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Troubleshooting Diagnostic Chart Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the diagnostic codes. DIAGNOSTIC CODE SYMPTOM Flashes SOLUTION Flashes 1 1 The garage door opener will not close. Safety reversing sensors are not installed, connected, or wires may be cut. Inspect sensor wires for a disconnected or cut wire. 1 2 The garage door opener will not close.
Troubleshooting Additional Troubleshooting My vehicle’s Homelink® is not programming to my garage door opener: Compatibility Bridge (not included) may be necessary for certain vehicles. Visit bridge.chamberlain. com to find out if a Bridge is needed. My garage door opener stops, reverses, beeps and flashes its lights: l Garage door opener has been activated through a device or feature such as Timer-toClose or garage door monitor.
Warranty Contact Information STOP! This garage door opener WILL NOT work until the safety reversing sensors are properly installed and aligned. Visit us onlineat: support.chamberlaingroup.com CHAMBERLAIN® LIMITED WARRANTY The Chamberlain Group, Inc.
Automatic Garage Door Opener Safety & Maintenance Guide Garage Door Opener Safety – An Automatic Decision A garage door is the largest moving object in the home. An improperly adjusted garage door and opener can exert deadly force when the door closes – which could lead to entrapment of children or adults and subsequent injury or death. Proper installation, operation, maintenance, and testing of the garage door and automatic opener are necessary to provide a safe, trouble-free system.
Routine Maintenance Can Prevent Tragedies Make monthly inspection and testing of your garage door and opener system a part of your regular routine. Review your owner’s manual for both the door and door opener. If you don’t have the owner’s manuals, contact the manufacturer(s) and request a copy for your specific model(s). Look for the opener model number on the back of the power unit. WARNING – SPRINGS ARE UNDER HIGH TENSION. ONLY QUALIFIED INDIVIDUALS SHOULD ADJUST THEM.
Repair Parts Rail Assembly Parts Installation Parts Description Part Number 1 Belt 2 Pulley 3 4 5 Trolley assembly: threaded shaft (1), clevis pin (1), and ring (1) 041C5141-2 6 “U” bracket 041D0598-1 7 D-shape threaded shaft 041A6689 8 Spring trolley nut 041B4103 Description Part Number 041A5250 1 Curved door arm 041B0035B 144C0054M 2 Door bracket with clevis pin and fastener 041A5047-1 Master link 004A1008 3 Emergency release rope and handle Rail 041A5665 4 Header brac
Repair Parts Garage Door Opener Parts - Model B4603T Description 4 10 2 1 7 11 9 6 4 5 Part Number 1 Sprocket and sprocket cover 041C1751 2 End panel 041-0198 3 Cover and light pod 041-0203 4 Control door panel 041-0204 5 Motor with travel module 041-0236 6 Logic board end panel 7 Logic board 041-0197 050DCTB 8 Travel module 9 Transformer 041D8071-4 041D0277-1 10 Line cord 041B4245-1 11 Terminal block 041A3150 Not shown 3 8 Badge Wire harness 49 041-0206 041-01
Repair Parts Garage Door Opener Parts - Model B4613T 5 1 Description 10 2 8 11 7 5 4 6 3 Part Number 1 Sprocket and sprocket cover 041C1751 2 End panel 041-0199 3 Cover and light pod 041-0203 4 Transformer 5 Control door panel 041-0204 6 Motor with travel module 041-0236 7 Logic board end panel 041-0197 8 Logic board 9 Travel module 041D8071-4 10 Line cord 041B4245-1 11 Terminal block 041D0277-1 050DCTB 041A3150 Not shown 9 Badge Wire harness 50 041-0206 041-018
Repair Parts Garage Door Opener Parts - Model B4643T 5 2 Description 10 1 8 7 11 4 5 6 Sprocket and sprocket cover 2 End panel 041-0198 3 Cover and light pod 041-0201 4 Transformer 5 Control door panel 041-0204 6 Motor with travel module 041-0236 7 Logic board end panel 041-0197 8 Logic board 9 Travel module 041D8071-4 041B4245-1 10 Line cord 11 Terminal block 12 Camera 041C1751 041D0277-2 050DCTB 041A3150 041-0041 Not shown 9 3 Part Number 1 Badge Wire harness
Repair Parts Garage Door Opener Parts - Models B6713T, and B6753T Description 5 10 1 2 8 7 11 4 5 6 9 3 Part Number 1 Sprocket and sprocket cover 041C1751 2 End panel 041-0199 Model B6713T Cover and light pod 041-0202 3 Model B6753T Cover and light pod 4 Transformer 5 Control door panel 041-0204 6 Motor with travel module 041-0236 7 Logic board end panel 8 Logic board 9 Travel module 041D8071-4 10 Line cord 041B4245-1 11 Terminal block 041A3150 12 Model B6753T Ca