Instructions / Assembly

ManualsBrandsChamberlain ManualsHome Safety ProductCWA2000

Batteries: If the Base Station batteries are low, the Base

Station will beep every 30 minutes. The AA batteries

in the Motion Sensor will last up to 2 years depending

on use (Lithium batteries are recommended for colder

environments). If the Motion Sensor batteries are low, the

Base Station will beep every 30 minutes until the batteries

are replaced. The Motion Sensor will continue to operate

with a low battery, however the light will not illuminate. For

peak performance, inspect batteries annually and replace as

needed.

Programming Additional Motion Sensors: The Base Station

can learn the code of up to 7 additional Motion Sensors,

responding with unique buzzes. To program additional

Motion Sensors see Step 4.

To order additional Motion Sensors call 1-800-528-9131.

Clear Memory: Press and hold the Learn Button on the Base

Station until 3 beeps are heard.

On/Off: To turn the Base Station on and off, hold down the

power button until you hear the on/off tone.

Volume: The Base Station is equipped with adjustable

volume controls. The lowest volume setting is the mute

feature.

Carton Inventory

Antenna

On/Off Button

Volume

BASE STATION

Operation and Features

Overview

The Wireless Motion Detection System uses a Passive Infra-Red (PIR) Motion Sensor to detect movement of people and vehicles.

The Base Station is powered by the DC adapter and the 4 AA batteries supply power in case of a power outage.

NOTE: The Base Station is intended for indoor use only.

Wireless Motion Detection System

Models CWA2000 and CWA2000C

Base Station

Motion Sensor

Rubber Pads

Mounting Plate

DC Adapter

(9 Vdc @ 200mA)

Sun/Rain Shield

Swivel bushing

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer

or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Summary of content (8 pages)

PAGE 1
Wireless Motion Detection System Models CWA2000 and CWA2000C Overview The Wireless Motion Detection System uses a Passive Infra-Red (PIR) Motion Sensor to detect movement of people and vehicles. The Base Station is powered by the DC adapter and the 4 AA batteries supply power in case of a power outage. NOTE: The Base Station is intended for indoor use only.
PAGE 2
Assembly and Programming 1 Attach Motion Sensor box to mounting plate with large silver screw. Tighten screw until Motion Sensor stays in place when repositioned. 2 Install 4 AA Alkaline batteries. (Lithium batteries recommended for colder environments.) LED light will ﬂash. 4 B Within 60 seconds, press the Learn Button on the inside of the Motion Sensor. LED light will illuminate and Base Station will buzz.
PAGE 3
Troubleshooting The Motion Sensor lights up, but the Base Station does not respond. The Motion Sensor must be programmed to Base Station (See Step 4). Ensure Base Station is on and the volume is turned up. Base Station beeps every 30 minutes. The batteries in the Base Station or the Motion Sensor(s) are low. Replace the 4 AA batteries. Check the Motion Sensor(s), if the LED illuminates on all of the Motion Sensors, change the batteries in the Base Station.
PAGE 4
NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 5
Sistema de detección de movimiento inalámbrico Modelos CWA2000 y CWA2000C Descripción general El Sistema de detección de movimiento inalámbrico usa un sensor de movimiento infrarrojo pasivo (PIR) para detectar el movimiento de personas y vehículos. La estación de base recibe alimentación por el adaptador de CC y 4 baterías AA en caso de una falla en el suministro de energía. NOTA: La estación de base está diseñada para uso interior únicamente.
PAGE 6
Montaje y programación 1 Sujete la caja del sensor de movimiento a la placa de montaje con el tornillo grande color plata. Ajuste el tornillo hasta que el sensor de movimiento quede ubicado en el lugar. 2 Instale 4 baterías alcalinas AA. (Las baterías de litio se recomiendan para ambientes más fríos.) La luz LED parpadeará. 4 5 Introduzca el paquete de baterías apuntando hacia el lado opuesto al tablero de circuitos y sujete la cubierta con los tornillos más pequeños (incluidos).
PAGE 7
Resolución de problemas El sensor de movimiento se enciende, pero la estación de base no responde. El sensor de movimiento se debe programar en la estación de base (vea el Paso 4). Asegúrese encender la estación y subir el volumen. La estación de base emite una señal sonora cada 30 minutos. Las baterías de la estación de base o de los sensores de movimiento están bajas. Reemplace las 4 baterías AA.
PAGE 8
AVISO: Este dispositivo cumple con la Parte 15 de la reglamentación de la FCC y las normas de RSS de Industry Canada para dispositivos exentos de licencia. La operación está sujeta a las siguientes dos condiciones: (1) es posible que este dispositivo no cause interferencias perjudiciales, y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas las interferencias que puedan causar operaciones no deseadas.