Owner's Manual
Table Of Contents
- Owner's Manual
- CONTENTS
- Preparation
- Assembly
- Installation
- STEP 1 Determine the header bracket location
- STEP 2 Install the header bracket
- STEP 3 Attach the rail to the header bracket
- STEP 4 Position the garage door opener
- STEP 5 Hang the garage door opener
- STEP 6 Install the light bulbs
- STEP 7 Attach the emergency release rope and handle
- STEP 8 Install the door bracket
- STEP 9 Connect the door arm to the trolley
- STEP 10 Install the door control
- STEP 11 Wire the door control to the garage door opener
- STEP 12 Attach the warning labels
- STEP 13 Install the Protector System®
- STEP 14 Wire the Safety Reversing Sensors
- STEP 15 Connect power
- STEP 16 Ensure the safety reversing sensors are aligned
- Adjustments
- Battery Backup
- Operation
- Maintenance
- Troubleshooting
- Accessories
- Warranty
- Contact Information
- Repair Parts
- SPANISH
39
Operation
Remote Control
Your remote control has been programmed at the factory to operate with your garage door opener.
Older Chamberlain remote controlsare NOTcompatible,see page 44 for compatible accessories.
Programming can be done through the door control or the learn button the garage door opener. To
program additional accessories refer to the instructions provided with the accessoryor visit
www.chamberlain.com. Ifyour vehicle is equipped with a Homelink
®
, you may require an external
adapter depending on the make,model,and year of your vehicle.Visitwww.homelink.com for additional
information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE MOTION-DETECTING CONTROL PANEL
1. Press the LEARNbutton on the door control to enter Programming Mode.
2. Press the LEARNbutton again, the LEDwill flash once.
3. Remote Control:
Press the button on the remote control thatyou wish to operate your garage door.
Keyless Entry:
Enter a 4-digit personal identification number (PIN) ofyour choice on the keyless entry
keypad.Then press the ENTERbutton.
The garage door opener lights will flash (or two clickswill be heard) when the code hasbeen
programmed.Repeat the steps for programming additional remote controls or keylessentry devices.
The command LED
will flash once.
The command LED will
flash once again.
1
2
OR
PIN
? ? ? ?
4
GHI
5
JKL
7
P
RS
8
TUV
9
WXY
0
Q
Z
*
#
E
NT
E
R
0 QZ
*
#
ENTER
6
M
NO
3
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE SMARTCONTROLPANEL
1. Press the navigation button below "MENU" to view the Features menu.
2. Use the navigation buttons to scroll to "PROGRAM".
3. Select "REMOTE"or "KEYPAD" to program from the program menu.
4. Remote Control:
Press the button on the remote control thatyou wish to operate your garage door.
Keyless Entry:
Enter a 4-digit personal identification number (PIN) ofyour choice on the keyless entry
keypad.Then press the ENTERbutton.
The garage door opener lights will flash (or two clickswill be heard) when the code hasbeen
programmed.Repeat the steps for programming additional remote controls or keylessentry devices.If
programming is unsuccessful, program the remote using the learn button.
Press to continue.
TO REMOTE
Press to continue.
1
2 3
OR
PIN
? ? ? ?
4
GHI
5
JKL
7
P
RS
8
TUV
9
WXY
0
QZ
*
#
E
NT
E
R
0 QZ
*
#
ENTER
6
MNO
4