Channel Receiver Specifications

ManualsBrandsChamberlain ManualsStereo ReceiverTCR2

TRICODE

TCR2 DUAL

CHANNEL RECEIVER

USED FOR TCR1 AND TCR2

The TriCode

digital receivers are designed for use with automatic

garage/gate operators and access control systems. All TriCode

products may be matched with Linear/Delta-3

, Multi-Code

, and

Stanley

radio products which may already be installed.

The TriCode

radio format provides a potential of 1024 different

digital codes. For Linear/Delta-3

compatible products, 256

different digital codes are available. The codes are set using

10-position DIP switch system.

U.S. Patent 6,915,146

SPECIFICATIONS

Output Rating: 5 Amps 28Vac/Vdc Max.

Power: 12Vdc or 18 to 34Vac/Vdc, @ 30ma

RF Frequency: 300 or 310 MHz

Accessory Transmitters: TC1, TC2 and TC4

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of

this receiver and/or transmitter are prohibited, except for changing the code setting or replacing

the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing the receiver.

To prevent possible SERIOUS INJURY or DEATH from a moving

gate or garage door:

• ALWAYS keep transmitters out of reach of children. NEVER permit

children to operate or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed.

NEVER permit anyone to cross path of moving gate or door.

WARNING

CAUTION

WARNING

Summary of content (4 pages)

PAGE 1
TRICODE® TCR2 DUAL CHANNEL RECEIVER ® USED FOR TCR1 AND TCR2 WARNING WARNING SPECIFICATIONS CAUTION WARNING Output Rating: 5 Amps 28Vac/Vdc Max. Power: 12Vdc or 18 to 34Vac/Vdc, @ 30ma RF Frequency: 300 or 310 MHz Accessory Transmitters: TC1, TC2 and TC4 To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is NOT connected BEFORE installing the receiver.
PAGE 2
POWER SWITCH SETTINGS NOTE: To avoid the possibility of duplicating codes in adjacent systems, all transmitters and receivers should be re-coded prior to operation. Unless using maximum number of codes the following four codes should not be used: · All DIP Switches ON · All DIP Switches OFF · DIP Switches alternating ON/OFF · DIP Switches alternating OFF/ON Power Supply Selection Setting The TriCode® receiver is factory set for 24 volt power input if 12 volt is required.
PAGE 3
OUTPUT RELAYS & CONFIGURATION SWITCH SETTINGS Setting Output Relay Mode The TriCode® receiver is factory set for momentary relay output “MNT”. Setting the Configuration Switch The TriCode® receiver is factory set for Linear/Delta-3TM. Locate the configuration switch and set it to the desired RF mode of operation (Figures 2 and 3). Modes are as follows: Linear/Delta-3TM: works with all “Linear/Delta-3TM” transmitters transmitted at 310 MHz using 8-bits ID system.
PAGE 4
DIP SWITCH SETTINGS & POWER CONNECTIONS Setting DIP Switch The TriCode® Receiver DIP switch CH1 is factory set OFF (1-10) and CH2 is factory set ON (1-10). Locate the 10 position DIP switch. If this is a new installation using TriCode® transmitters, randomly set switches matching those of the transmitter. Never use factory settings. If receiver is used with Linear/Delta 3TM, Multi-CodeTM or StanleyTM transmitters, match the receiver DIP switch to the above transmitters.