User Manual

ManualsBrandsChamberlainrp ManualsBuilding SuppliesChamberlain Group KLIK3U-BK Clicker Universal 2-Button Garage Door Opener Remote with Visor Clip, Black

To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:

• ALWAYSkeepremotecontrolsoutofreachofchildren.NEVERpermitchildrentooperate,orplaywithremotecontrol

transmitters.

• ActivategateordoorONLYwhenitcanbeseenclearly,isproperlyadjustedandtherearenoobstructionstodoortravel.

• ALWAYSkeepgateordoorinsightuntilcompletelyclosed.NEVERpermitanyonetocrosspathofmovinggateordoor.

Universal Remote Control

Read instructions thoroughly BEFORE beginning.

If using the Universal Remote Control with residential door openers, the remote control must be used only with

door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always

located on or near the bottom of the door track.

STOP

MODEL KLIK3U

TABLE OF CONTENTS

GETTING STARTED ........................................................................... 2

LOCATE THE PROGRAM/LEARN BUTTON ...................................... 3-7

Chamberlain

products ................................................................ 3

Genie

products ............................................................................ 4

Linear

products........................................................................... 5

Wayne Dalton

products .............................................................. 5

LiftMaster

products .................................................................... 6

Overhead Door

products ............................................................ 6

Stanley

products ......................................................................... 7

GARAGE DOOR OPENERS ..............................................................8-9

Programming to a garage door opener with a

Program/LEARN button ................................................................ 8

Programming to a Genie

Intellicode

garage door opener ...................................................................... 9

Commercial Door Operators .......................................................... 10

Programming to a commercial door operator

with a Program/LEARN button ................................................... 10

GATE OPERATORS .....................................................................11-13

Program to a gate operator

with a Program/LEARN button ................................................... 11

Programming to a GTO/Mighty Mule gate

operator without a remote control ............................................ 12

Programming to a GTO/Mighty Mule gate

operator with a remote control .................................................. 13

EXTERNAL RECEIVERS ..............................................................14-15

Programming to an external receiver

with DIP switches ....................................................................... 14

Programming to an external receiver

with a Program/LEARN button ................................................... 15

ALTERNATE PROGRAMMING OPTIONS .....................................16-17

Alternate programming option for products

with a Program/LEARN button ................................................... 16

Alternate programming option for products

with DIP switches ....................................................................... 17

NEED HELP? ................................................................................... 18

BATTERY ........................................................................................ 19

Summary of content (19 pages)

PAGE 1
MODEL KLIK3U Universal Remote Control Table of Contents Getting Started............................................................................ 2 LOCATE THE PROGRAM/LEARN BUTTON.......................................3-7 Chamberlain products................................................................. 3 Genie® products............................................................................. 4 Linear® products...........................................................................
PAGE 2
getting started The remote control can be programmed to activate up to two products, such as a garage door opener, gate operator, or commercial door operator. The images throughout this manual are for reference only and your product may look different. Gate Operator Garage Door Opener Commercial Door Operator Button 2 Button 1 Programmed separately from Button 1. Programmed separately from Button 2. DIP Switches Program Button Used for programming products with DIP switches.
PAGE 3
Locate the PROGRAM/LEARN BUTTON chamberlain products 3
PAGE 4
Locate the PROGRAM/LEARN BUTTON GENIE products Learn Code Button Program Set Button 4
PAGE 5
Locate the PROGRAM/LEARN BUTTON LINEAR products Learn Button Learn Button WAYNE DALTON products Program SW Button 5
PAGE 6
Locate the PROGRAM/LEARN BUTTON liftmaster products Yellow Learn Button Purple Learn Button Orange Learn Button Green Learn Button overhead door products Learn Code Button 6
PAGE 7
Locate the LEARN BUTTON stanley products Learn Button 7
PAGE 8
garage door openers Programming to a Garage Door Opener with a Program/LEARN Button The Program/LEARN button is typically located on the back or side panel of the garage door opener or an external receiver. For help locating your Program/LEARN button refer to the Help section in this manual or contact your garage door opener manufacturer. If you have a Genie® Intellicode® 2 garage door opener go to the next page. The images throughout this manual are for reference only and your product may look different.
PAGE 9
garage door openers (continued) Programming to a Genie® Intellicode® 2 Garage Door Opener Before starting, you MUST have a Genie® Intellicode® 2 remote control with at least one button already programmed to the garage door opener. The images throughout this manual are for reference only and your product may look different. 1 2 Press the program button on the Universal Remote Control until the LED turns on.
PAGE 10
commercial door operatorS Programming to a Commercial Door Operator with a LEARN Button The Program/LEARN button is typically located on the logic board of the operator or an external receiver. For help locating your Program/LEARN button contact your commercial door operator manufacturer. The images throughout this manual are for reference only and your product may look different. 1 2 Press the program button on the remote control until the LED turns on.
PAGE 11
gate operators Programming to a Gate Operator with a Program/LEARN Button The Program/LEARN button is typically located on the control board of the operator or an external receiver. For help locating your Program/LEARN button contact your gate operator manufacturer. The images throughout this manual are for reference only and your product may look different. 1 2 Press the program button on the remote control until the LED turns on. ress and release the Program/LEARN button* on your P gate operator.
PAGE 12
gate operators (continued) Programming to a GTO/Mighty Mule Gate Operator without a Remote Control If you have an existing GTO remote control go to the next page. The images throughout this manual are for reference only and your product may look different. 1 2 Set the remote control DIP switches 1-9 to any combination. Press the program button on the remote control until the LED turns on. LED Program Button 3 4 Press and release the remote control button, the LED will flash.
PAGE 13
gate operators (continued) Programming to a GTO/Mighty Mule Gate Operator with a Remote Control STOP If you don’t have an existing GTO remote control go to the previous page. Before beginning, check the DIP switches on the GTO remote control. If any of the DIP switches are in the "0" position, move them to either the "+" or "-" position and reprogram the GTO remote control to the gate operator (refer to the gate operator instructions).
PAGE 14
EXTERNAL RECEIVERS Programming to an External Receiver with DIP Switches STOP If using the Universal Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. The external receiver is typically located on the product or mounted near the product.
PAGE 15
EXTERNAL RECEIVERS (continued) Programming to an External Receiver with a Program/LEARN Button STOP If using the Universal Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. The external receiver is typically located on the product or mounted near the product.
PAGE 16
Alternative programming options Alternative programming option for products with a Program/LEARN Button The Program/LEARN button is typically located on the product or an external receiver. For help locating your Program/LEARN button refer to the Help section in this manual or contact your product manufacturer. The images throughout this manual are for reference only and your product may look different.
PAGE 17
ALTERNATIVE programming options (continued) Alternative programming option for products with DIP Switches STOP If using the Universal Remote Control with residential door openers, the remote control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track. The DIP switches are typically located on the product or an external receiver.
PAGE 18
NEED HELP? The remote control will not program to a product with DIP switches. • Check the battery in the remote control. The LED should light when you press a button. Replace the battery if necessary. • I f programming with 2 position DIP switches, reverse the DIP switches (OFF to ON and ON to OFF), then repeat the programming steps. • F or Chamberlain remote controls DO NOT use the “0” position, use “+” or “-”.
PAGE 19
BATTERY To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. To reduce risk of fire, explosion or chemical burn: • Replace ONLY with 3V2032 coin batteries. • DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.