OPERATOR'S MANUAL MODEL #100382 2600 PSI Pressure Washer or visit championpowerequipment.com READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do so could result in serious injury. This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
100382 - 2600 PSI Pressure Washer TABLE OF CONTENTS Introduction................................................. 3 Table of Contents Storage....................................................... 18 Pressure Washer Storage.................................. ..... 18 Engine Stored for Less than 30 Days.......................... 19 Safety Definitions........................................ 3 Engine Stored for Over 30 Days................................ 19 Safety Symbols.................................
Introduction 100382 - 2600 PSI Pressure Washer INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power Equipment (CPE) product. CPE designs, builds, and supports all of our products to strict specifications and guidelines. With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying service. The purpose of safety symbols is to attract your attention to possible dangers.
Safety Symbols 100382 - 2600 PSI Pressure Washer SAFETY SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYMBOL MEANING Read the Operator’s Manual. To reduce the risk of injury, user must read and understand operator’s manual before using this product. Electric Shock.
100382 - 2600 PSI Pressure Washer IMPORTANT SAFETY INSTRUCTIONS WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Important Safety Instructions WARNING Sparks can result in fire or electrical shock. When servicing the pressure washer: Disconnect the spark plug wire and place it where it cannot contact the plug. DO NOT check for spark with the plug removed.
100382 - 2600 PSI Pressure Washer Important Safety Instructions WARNING NOTICE NEVER spray flammable liquids or use pressure washer in areas containing combustible dust, liquids, or vapor. Improper treatment or use of the pressure washer can damage it, shorten its life and void your warranty. NEVER operate this machine in a closed building or in or near an explosive environment. Use the pressure washer only for intended uses. Operate only on level surfaces.
100382 - 2600 PSI Pressure Washer WARNING Important Safety Instructions DANGER Use of pressure washers can create wet walking surfaces. While using a pressure washer, forces from the gun can cause you to loose footing and fall. Fuel and fuel vapors are highly flammable and extremely explosive. –– Use only on a level surface. Unintentional startup can result in entanglement, traumatic amputation or laceration. –– Make sure there is proper drainage to dissipate water.
Controls and Features 100382 - 2600 PSI Pressure Washer CONTROLS AND FEATURES Read this operator’s manual before operating your pressure washer. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. 13 14 1 12 2 11 3 4 9 5 6 10 15 8 16 7 1. Nozzles 11. Fuel Tank – 0.9 gal. (3.4 L) 2. High Pressure Hose 12. Trigger Gun Assembly – Gun and spray wand 3. Muffler 13.
Assembly 100382 - 2600 PSI Pressure Washer Parts Included ASSEMBLY Gun Assembly Your pressure washer requires some assembly. This unit ships from our factory without oil. It must be properly serviced with fuel and oil before operation. If you have any questions regarding the assembly of your pressure washer, call our help line at 1-877-338-0999. Please have your serial number and model number available. Spray Wand (A)......................................................................
Assembly 100382 - 2600 PSI Pressure Washer Add Engine Oil Degrees Celsiusº (Outside) CAUTION DO NOT attempt to crank or start the engine before it has been properly filled with the recommended type and amount of oil. Damage to the pressure washer as a result of failure to follow these instructions will void your warranty. Full Synthetic 5W-30 NOTICE The recommended oil type is 10W-30 automotive oil. 1. Place the pressure washer on a flat level surface.
Assembly 100382 - 2600 PSI Pressure Washer Add Fuel NOTICE 1. Use clean, fresh, regular unleaded fuel with a minimum octane rating of 85 and an ethanol content of less than 10% by volume. 2. DO NOT mix oil with fuel. 3. Clean the area around the fuel cap. 4. Remove the fuel cap. 5. Slowly add fuel to the tank. DO NOT OVERFILL. Fuel can expand after filling. A minimum of ¼ in. (6.4 mm) of space left in the tank is required for fuel expansion, more than ¼ in. (6.4 mm) is recommended.
Assembly 100382 - 2600 PSI Pressure Washer Connect the High Pressure Hose 1. Completely uncoil and straighten the high pressure hose to prevent kinks. 2. With the hose faucet turned completely off, attach the end of the garden hose to the water inlet. Tighten by hand. 2. Align the collar on the hose to the threaded outlet on the pump. 3. Insert the high pressure hose collar onto the threaded outlet. 4. Turn the collar clockwise to tighten the hose securely to the pump.
Operation 100382 - 2600 PSI Pressure Washer OPERATION NOTICE Pressure Washer Location This pressure washer must have at least 5 ft. (1.5 m) of clearance from combustible material. Leave at least 3 ft. (91.4 cm) of clearance on all sides of the pressure washer to allow for adequate cooling, maintenance and servicing. Place the pressure washer in a well ventilated area. DO NOT place the pressure washer near vents or intakes where exhaust fumes could be drawn into occupied or confined spaces.
Operation 100382 - 2600 PSI Pressure Washer Use the following table to determine which nozzle to use. NOZZLE SELECTION GUIDE 0° 25° Soap HIGH PRESSURE WASH 0° Abrasive LOW PRESSURE WASH 25° Soap Gentle Concrete, Brick, Masonry Siding, Gutters, Home Fencing, Deck, Patio Lawn and Garden Equipment, Boats, RVs Recommended nozzle Use with caution High Pressure Wash CAUTION Always engage the trigger safety latch when the unit is not in use.
Operation 100382 - 2600 PSI Pressure Washer are customized for pressure washer use on specific cleaning tasks. Pressure washer detergents are as thick as water. Using thicker detergents – like dish soap – will clog the chemical injection system. System Flush After using detergents, flush the suction system by placing the detergent suction tube into a bucket of clean water. WARNING NOTICE Use only detergents designed for pressure washers.
Maintenance 100382 - 2600 PSI Pressure Washer CAUTION Select the correct main jet part number corresponding to the carburetor code found on your particular carburetor. Running the unit for more than one minute without spraying water causes heat to build up in the pump. Carburetor Code In the event that the pump gets too hot, a thermal relief valve will open to release the hot water. Running the unit without spraying water can damage pump components and will void the warranty.
Maintenance 100382 - 2600 PSI Pressure Washer Cleaning the Pressure Washer CAUTION DO NOT spray the pressure washer with water. Water can contaminate the fuel system and can enter the engine through the cooling slots and damage the engine. 1. Use a damp cloth to clean exterior surfaces of the pressure washer. 5. Add up to 0.6 qt. (0.6 L) of oil and replace oil fill cap/ dipstick. DO NOT OVERFILL. 6. Dispose of used oil at an approved waste management facility.
Storage 100382 - 2600 PSI Pressure Washer 8. Reattach the air filter cover and using your fingers, insert the thumb screws into the top and bottom holes of the air filter cover. Screw until tight. Be sure not to over tighten. Cleaning the Spark Arrester 1. Allow the engine to cool completely before servicing the spark arrester. 2. Remove the four (4) screws holding the cover plate which retains the end of the spark arrester to the muffler. warranty.
Storage 100382 - 2600 PSI Pressure Washer 3. Clean the pressure washer according to the instructions in the Maintenance section. 4. Store the unit in a clean, dry area out of direct sunlight. Engine Stored for Less than 30 Days 1. Allow the engine to cool completely before storage. 2. Clean engine according to the Maintenance section. 3. To extend the fuel storage life add a properly formulated fuel stabilizer to the tank. 4. Ensure the fuel valve is in the “OFF” position. 5.
Specifications 100382 - 2600 PSI Pressure Washer SPECIFICATIONS Pressure Washer Specifications Model........................................................................... 100382 Max Pressure.............................................................2600 PSI Max Volume................................................................2.2 GPM Max Water Temperature.......................................140°F (60°C) Fuel Capacity.....................................................0.9 gal. (3.
12 29 23 22 28 24 21 12 27 26 25 31 30 27 20 19 18 31 30 17 28 12 32 33 16 15 14 29 12 13 34 17 10 11 9 8 5 6 4 3 7 2 1 100382 - 2600 PSI Pressure Washer Specifications Parts Diagram 21
Specifications 100382 - 2600 PSI Pressure Washer Parts List # Part Number Description Qty. # 1 19 2.08.139 Part Number Bolt M6 x 35 Description Qty. 2 20 254.200701.06.78 Handle, Frame 1 1 26.115 Engine 2 2.14.001 Key, SQ 4.78 x 4.78 x 40 1 21 254.201600.00.78 Mounting Plate 1 3 2.08.010 Bolt 5/16-24 x 22 4 22 1.5789.0615 Flange Bolt M6 x 15 2 4 1.93.08 Lock Washer Ø8 4 23 254.200012.03.78 Hose Hanger 1 5 252.251003.00 Inlet Filter Gasket 1 6 252.251000.
137 1 133 132 108 131 130 138 142 2 14 129 128 3 127 4 126 5 134 15 6 135 7 20 16 136 8 21 125 9 10 22 23 17 20 11 18 24 112 99 12 25 112 99 79 19 124 46 79 123 122 13 26 27 45 44 43 42 41 40 28 29 116 30 42 121 120 119 118 117 141 50 49 48 47 31 11 51 32 11 109 33 53 54 108 111 112 113 114 115 55 107 34 52 56 106 110 140 35 57 36 58 104 59 61 62 105 103 60 69 63 37 64 68 65 66 70 38 71 67 72 74
Specifications 100382 - 2600 PSI Pressure Washer Engine Parts List # Part Number Description Qty. # 38 1.5789.0832.0.8 Part Number Flange Bolt M8 x 32 Description Qty. 6 39 22.031000.01.48 Oil Filter Cap, Yellow 1 1 1.5789.0608 Flange Bolt M6 x 8 5 2 22.061100.00.2 Cover, Recoil Starter, Black 1 40 23.110005.01 Spring, Throttle Return 1 3 21.061005.00 Spring, Recoil Starter 1 41 21.110003.00 Arm, Governor 1 4 2.10.003 Rope Ø5 x 1550 1 42 1.6177.
Specifications 100382 - 2600 PSI Pressure Washer # Part Number Description Qty. 76 22.040009.00 Rocker Arm 2 77 22.040012.00 Screw, Valve Adjustment 2 78 21.040021.00 Nut M6 x 0.5, Lock 2 79 1.97.1.06 Washer Ø6 6 # Part Number Description Qty. 116 22.070014.00 Pipe, Reversal Valve 1 117 2.06.006 Clamp Ø7 x Ø1 1 118 22.070013.00 Pipe, Air Cleaner 1 119 24.070700.00 Carbon Canister, 45CC 1 120 1.845.2965 Screw ST2.9 x 6.5 2 80 1.6177.1.06 Flange Nut M6 2 121 2.03.
Specifications 100382 - 2600 PSI Pressure Washer Troubleshooting Problem Cause Solution No fuel. Add fuel. Faulty spark plug. Replace spark plug. Pressure washer will not start; Low oil level. Pressure washer starts but runs roughly. Fill crankcase to the proper level. Place pressure washer on a flat, level surface. Choke in the wrong position. Adjust choke. Spark plug wire loose. Attach wire to spark plug. Pressure washer gallops. Engine governor defective. Contact the help line.
WARRANTY WARRANTY* CHAMPION POWER EQUIPMENT 2 YEAR LIMITED WARRANTY Other Exclusions This warranty excludes: –– Cosmetic defects such as paint, decals, etc. –– Wear items such as filter elements, o-rings, etc. Champion Power Equipment (CPE) will register this warranty upon receipt of your Warranty Registration Card and a copy of your sales receipt from one of CPE’s retail locations as proof of purchase.
Champion Power Equipment, Inc. (CPE), The United States Environment Protection Agency (U.S. EPA.) and the California Air Resources Board (CARB) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB) emission regulations.
EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter. 2.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the engine) Systems covered by this warranty Fuel Metering System Fuel regulator, Carburetor and internal parts Air Induction System Air cleaner, Intake manifold Ignition System Spark plug and parts, Magneto ignition system Exhaust System Exhaust manifold, catalytic converter Miscellaneous Parts Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed systems.
Champion Power Equipment, Inc (CPE) and Environment and Climate Change Canada (ECCC) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with Environment and Climate Change Canada (ECCC) emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: CPE is pleased to explain the Emission Control Systems Warranty on your 2017 small off-road engine. New engines must be designed, built and equipped, at the time of sale, to meet ECCC regulations for small non-road engines.
EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System Warranty Coverage. Emission Control System Warranty (ECS Warranty): 1. APPLICABILITY: The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter. 2.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the engine) Systems covered by this warranty Fuel Metering System Air Induction System Ignition System Exhaust System Miscellaneous Parts Evaporative Emissions Parts description Fuel regulator, carburetor and internal parts Air cleaner, intake manifold Spark plug and parts, magneto ignition system Exhaust manifold, catalytic converter Tubing, fittings, seals, gaskets, and clamps associated with these listed system