OPERATOR'S MANUAL MODEL #100778 2800 PSI Pressure Washer REGISTER YOUR PRODUCT ONLINE at championpowerequipment.com or visit championpowerequipment.com SAVE THESE INSTRUCTIONS. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do so could result in serious injury. This manual should remain with the product.
Table of Contents 100778 - 2800 PSI Pressure Washer TABLE OF CONTENTS Maintenance................................................. 21 Cleaning the Pressure Washer.......................... .......... 21 Introduction.................................................... 3 Cleaning Spray Nozzle.................................. .......... 22 Safety Definitions........................................... 3 Changing the Engine Oil.......................................... 22 Important Safety Instructions..
Introduction 100778 - 2800 PSI Pressure Washer INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power Equipment (CPE) product. CPE designs, builds, and supports all of our products to strict specifications and guidelines. With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying service. The purpose of safety symbols is to attract your attention to possible dangers.
Important Safety Instructions 100778 - 2800 PSI Pressure Washer IMPORTANT SAFETY INSTRUCTIONS WARNING Spark from removed spark plug wire can result in fire or electrical shock. WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov When servicing the pressure washer: Disconnect the spark plug wire and place it where it cannot contact the plug or any other metal object. DANGER Pressure washer exhaust contains carbon monoxide, a colorless, odorless, poisonous gas.
Important Safety Instructions 100778 - 2800 PSI Pressure Washer NOTICE WARNING NEVER spray flammable liquids or use pressure washer in areas containing combustible dust, liquids, or vapor. Improper treatment or use of the pressure washer can damage it, shorten its life and void your warranty. NEVER operate this machine in a closed building or in or near an explosive environment. Use the pressure washer only for intended uses.
Important Safety Instructions 100778 - 2800 PSI Pressure Washer When adding or removing gasoline: WARNING – DO NOT light or smoke cigarettes. High pressure spray can splash back at operator or propel objects. – Always turn the pressure washer off and let cool for a minimum of two minutes before removing the gasoline cap. Afterwards, loosen gasoline cap to relieve pressure from the gasoline tank. NEVER: allow children to operate any pressure washer or play nearby.
Important Safety Instructions 100778 - 2800 PSI Pressure Washer Safety and Dataplate Labels These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement. E C B A D LABEL DESCRIPTION DANGER A B Risk of Injections. To reduce the risk of injection or injury, never direct a water stream towards people or pets or place any body part in the stream.
Important Safety Instructions 100778 - 2800 PSI Pressure Washer Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYMBOL MEANING Read Operator’s Manual. To reduce the risk of injury, user must read and understand operator’s manual before using this product. Electric Shock.
Important Safety Instructions 100778 - 2800 PSI Pressure Washer Operation Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.
Controls and Features 100778 - 2800 PSI Pressure Washer CONTROLS AND FEATURES Read this operator’s manual before operating your pressure washer. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. 1 10 2 9 3 14 4 13 8 5 11 6 12 7 24 25 23 15 22 16 17 21 18 20 19 Pressure Washer 1. Upper handle 6. Support leg 11. Detergent tank cap 2. Nozzles 7. Wheel 12. Detergent tank 3. Detergent barb 8. Spray wand 13.
Controls and Features 100778 - 2800 PSI Pressure Washer Parts Included Part Wheels Part Qty. 2 Support Leg 2 Detergent tank 1 Detergent hose 1 Top handle 1 Trigger gun 1 Spray wand 1 Nozzle"0", 00025 1 Nozzle "15", 15025 1 Nozzle "25", 25025 1 Nozzle "40", 40025 1 Nozzle "Detergent", 65400 1 Trigger gun holder 1 High pressure hose, 25ft. 1 Hose strap 1 Bottle of engine oil, 20.3 fl. oz.
Assembly 100778 - 2800 PSI Pressure Washer ASSEMBLY Support Legs 1. Attach the supports legs to the pressure washer frame with 2 M8 x 45 flange bolts and 2 M8 flange lock nuts per leg. Tighten to 8.8 ft-lb − 10.3 ft-lb (12-14 Nm). Your pressure washer requires some assembly. This unit ships from our factory without oil. It must be properly serviced with fuel and oil before operation. If you have any questions regarding the assembly of your pressure washer, call our help line at 1-877-338-0999.
Assembly 100778 - 2800 PSI Pressure Washer Nozzles Trigger Gun Holder 1. Nozzles are stored in the top panel. To store the nozzle, press it into the corresponding opening. To remove the nozzle, just pull the nozzle out. 1. Align the trigger gun holder to the frame. 2. Attach to the frame with 2 M6 x 45 flange bolts and M6 nuts. Tighten to 8.8 ft-lb − 10.3 ft-lb (12-14 Nm). Do not overtighten. High Pressure Hose Strap The High pressure hose storage strap is provided to store your hose when not in use.
Assembly 100778 - 2800 PSI Pressure Washer Attach the Trigger Gun Assembly 1. Attach the spray wand to the trigger gun. 2. Rotate (clockwise) the M22 coupler on the trigger gun until the spray wand is secure. Do not overtighten. NOTICE Be careful to avoid cross-threading, which can cause the hose to leak during use. 5. Gently pull on the hose to be certain it is properly secured. 3. Connect the end of the high pressure hose to the gun inlet. Tighten connection clockwise. Do not overtighten.
Assembly 100778 - 2800 PSI Pressure Washer NOTICE Do not run the pressure washer without water supply connected and turned on, as this may damage the high pressure seals and decrease pump life. Completely unwind the hose from its reel or coil and make sure the hose is not being restricted by tires, rocks, or any other objects that may lessen or prevent water flow to the pressure washer. Add Engine Oil CAUTION 4. Check engine oil level at every use and add as needed.
Assembly 100778 - 2800 PSI Pressure Washer CAUTION NOTICE Use unleaded gasoline with a minimum octane rating of 85 and an ethanol content of 10% or less by volume. Synthetic oil may be used after the 5 hour initial break-in period. Using synthetic oil does not increase the recommended oil change interval. Full synthetic 5W-30 oil will aid in starting in cold ambient < 41º F (5º C) temperatures. DO NOT light cigarettes or smoke when filling the tank. DO NOT mix oil and gasoline.
Operation 100778 - 2800 PSI Pressure Washer OPERATION 4. Pull the starter cord slowly until resistance is felt and then pull rapidly. SEE NOTE. Pressure Washer Location This pressure washer must have at least 5 ft. (1.5 m) of clearance from combustible material. Leave at least 3 ft. (91.4 cm) of clearance on all sides of the pressure washer to allow for adequate cooling, maintenance and servicing. Place the pressure washer in a well ventilated area.
Operation 100778 - 2800 PSI Pressure Washer Distance from Cleaning Surface The distance between the spray nozzle and the cleaning surface is another factor that affects the impact force of the water. The impact force of the water increases as the nozzle is moved closer to the surface. You can vary the impact force by controlling – The nozzle’s fan pattern. – The nozzle’s angle to the cleaning surface. – The nozzle’s distance from the cleaning surface.
Operation 100778 - 2800 PSI Pressure Washer High Pressure Wash NOTICE CAUTION Use only detergents designed for pressure washers. Do not use household detergents, acids, alkalines, bleaches, solvents, flammable material, or industrial grade solutions, which can damage the pump or cause property damage. Many detergents may require mixing prior to use. Prepare cleaning solution as instructed on the solution bottle. Always test in an inconspicuous area before beginning.
Operation 100778 - 2800 PSI Pressure Washer 3. Uncoil the rest of the detergent suction hose. To reduce the risk of bodily injury or property damage, always follow this procedure whenever spraying is stopped, when work is completed, and before checking or repairing any part of the system. 4. Connect the other end of the detergent suction hose to the detergent barb on the pump. 1. Engage the trigger gun lock out. 2. Turn the unit off. 3. Shut off the water supply. 4.
Maintenance 100778 - 2800 PSI Pressure Washer 2. Let the engine run until fuel starvation has stopped the engine. This usually takes a few minutes. Carb. Code P19-17-H 3. Press the engine switch to the “OFF” position. High Alt. Jet Part Number Min. Altitude 26.131017.04.01.H 3,500 ft. (1,067 m) WARNING Operation using the alternative main jet at elevations lower than the recommended minimum altitude can damage the engine.
Maintenance 100778 - 2800 PSI Pressure Washer 2. Use a soft bristle brush to remove dirt and oil. 4. Add oil according to Add Engine Oil in Assembly section. DO NOT OVERFILL. Oil not included for routine maintenance. 3. Use an air compressor (25 PSI) to clear dirt and debris from the pressure washer. 5. Dispose of used oil at an approved waste management facility. 4. Inspect all air vents and cooling slots to ensure that they are clean and unobstructed.
Maintenance 100778 - 2800 PSI Pressure Washer Cleaning the Air Filter Cleaning the Spark Arrester 1. Using your finger, pry the outer tab up slightly and lift the air filter cover above the tab lock position. 1. If so equipped, allow the engine to cool completely before servicing the spark arrester. 2. Remove the screws holding the cover plate which retains the end of the spark arrester to the muffler. 3. Remove the spark arrester screen. 4.
Storage 100778 - 2800 PSI Pressure Washer Maintenance Schedule Engine Stored for Less than 30 Days Follow the service intervals indicated in the schedule below. Service your pressure washer more frequently when operating in adverse conditions. Contact our help line at 1-877-338-0999 to locate the nearest Champion Power Equipment certified service dealer for your maintenance needs. 1. Allow the engine to cool completely before storage. 2. Clean engine according to the Maintenance section. 3.
Storage 100778 - 2800 PSI Pressure Washer Winter Storage NOTICE Protect your pressure washer parts from freezing. 1. Apply all storage instructions from previous sections. Our engines work well with 10% or less ethanol blend fuels. When using blended fuels there are some issues worth noting: 2. Make sure pressure washer hose is free of all water before storing for winter. – Ethanol-gasoline blends can absorb more water than gasoline alone. 3.
Specifications 100778 - 2800 PSI Pressure Washer SPECIFICATIONS NOTICE Temperature will affect engine oil and engine performance. Change the type of engine oil used based on the temperature to suit the engine needs. Pressure Washer Specifications Model........................................................ 100778 Max Pressure.. ............................................. 2800 PSI Max Volume................................................. 2.1 GPM Fuel Specifications Max Water Temperature (°F/°C).
9.1 27 33 32 29 31 30 24 34 23 25 35 21 27 26 22 36 29 18 19 20 28 37 17 38 18 16 14 39 18 29 15 12 13 42 43 10 11 9 5 9.
Specifications 100778 - 2800 PSI Pressure Washer Parts List # Qty. # 1 26.201 Part Number Engine, 196cc Description 1 32 122.201400.04 Rubber, Support 2 2 2.14.001 Key, SQ 4.78 x 4.78 x 40 1 33 1.5789.0825 Flange Bolt M8 x 25 2 3 2.08.010 Bolt 5/16-24 x 22 4 34 122.201501.00 Pin Roll, Wheel 2 4 1.93.08 Lock Washer Ø8 4 35 254.201702.04.48 Cap, Wheel, Yellow 2 254.201701.04.48 Wheel, PU, Yellow 2 Part Number Description Qty. 5 252.251003.
1 100 116 2 3 14 110 4 5 6 29 7 22 15 8 9 21 10 16 26 99 97 92 17 23 24 79 96 114 50 120 11 13 26 27 28 85 117 29 18 120 25 19 32 30 31 49 48 20 47 46 45 119 118 12 33 83 54 53 52 51 101 47 34 11 112 36 37 57 11 41 38 109 58 59 56 110 115 50 60 98 113 108 111 84 39 61 106 64 63 62 65 105 107 66 68 40 67 72 55 69 74 76 70 75 42 71 78 77 83 80 81 88 82 87 73 89 43 93 94 86 95 44 90 22 106 69 103 104
Specifications 100778 - 2800 PSI Pressure Washer Engine Parts List # Part Number Description Qty. 1.16674.0608 Flange Bolt M6 x 8 3 2 27.061100.02.2 Cover, Recoil Starter, Black 1 3 21.061005.00 Spring, Recoil Starter 4 2.10.003.1 5 21.061001.01 1 # Part Number Description Qty. 40 21.031000.00.48 Oil Dipstick Assembly, Yellow 41 27.091000.05 Air Cleaner Assembly 1 1 42 24.030007.00 Cover, Crankcase 1 Rope Ø4 x 1550, Black 1 43 1.5789.
Specifications 100778 - 2800 PSI Pressure Washer # Part Number Description Qty. # Part Number Description Qty. 80 21.040009.00 Rocker Arm 2 104 1.93.08 Lock Washer Ø8 2 81 21.040020.00 Screw, Valve Adjustment 2 105 26.010100.00 Cylinder Head, 196cc 1 82 21.040021.00 Nut M6, Lock 2 106 2.01.009 Stud Bolt M6 x 110 2 83 1.5789.0608 Flange Bolt M6 x 8 3 107 24.130002.00 Gasket, Insulator 1 84 2.06.006 Clamp Ø7 x Ø1 1 108 23.130001.00 Insulator, Carburetor 1 85 21.
Troubleshooting 100778 - 2800 PSI Pressure Washer TROUBLESHOOTING Problem Cause Solution No fuel. Add fuel. Faulty spark plug. Replace spark plug. Pressure washer will not start; Low oil level. Pressure washer starts but runs roughly. Fill crankcase to the proper level. Place pressure washer on a flat, level surface. Choke in the wrong position. Adjust choke. Spark plug wire loose. Attach wire to spark plug. Pressure washer gallops. Engine governor defective. Contact the help line.
WARRANTY* Other Exclusions CHAMPION POWER EQUIPMENT This warranty excludes: 2 YEAR LIMITED WARRANTY – Cosmetic defects such as paint, decals, etc. – Wear items such as filter elements, o-rings, etc. Warranty Qualifications To register your product for warranty and FREE lifetime call center technical support please visit: https://www.championpowerequipment.com/register To complete registration you will need to include a copy of the purchase receipt as proof of original purchase.
CHAMPION POWER EQUIPMENT, INC. (CPE) AND THE UNITED STATES ENVIRONMENT PROTECTION AGENCY (U.S. EPA) EMISSION CONTROL SYSTEM WARRANTY Your Champion Power Equipment (CPE) engine complies with U.S. EPA emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The US EPA AND CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2020 small off-road engine (SORE) and engine powered equipment.
EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines (SORE). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter. 2.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the engine) Systems covered by this warranty Parts Description Fuel Metering System Fuel regulator, Carburetor and internal parts Air Induction System Air cleaner, Intake manifold Ignition System Spark plug and parts, Magneto ignition system Exhaust System Exhaust manifold, catalytic converter Miscellaneous Parts Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed systems.