OPERATOR'S MANUAL MODEL #200947 Walk Behind Blower REGISTER YOUR PRODUCT ONLINE at championpowerequipment.com or visit championpowerequipment.com WARNING To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. If you do not understand the warnings and instructions in the operator’s manual, do not use this product. READ AND SAVE THIS MANUAL.
Table of Contents 200947 - Walk Behind Blower TABLE OF CONTENTS Storage................................................ ......... 24 Short Term Engine Storage (Up to 30 Days)..................... 24 Introduction.................................................... 3 Long Term Engine Storage (30 Days – 1 Year)......... .......... 24 Safety Definitions........................................... 3 Specifications...................................... ......... 26 Important Safety Instructions............
Introduction 200947 - Walk Behind Blower INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power Equipment (CPE) product. CPE designs, builds, and supports all of our products to strict specifications and guidelines. With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying service. The purpose of safety symbols is to attract your attention to possible dangers.
Important Safety Instructions 200947 - Walk Behind Blower IMPORTANT SAFETY INSTRUCTIONS DANGER DO NOT allow children or untrained individuals to use this unit. WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov WARNING Maintain a firm grip on the handle with both hands while using the blower. DANGER The blower engine exhaust contains carbon monoxide, a colorless, odorless, poison gas. Breathing carbon monoxide will cause nausea, dizziness, fainting or death.
Important Safety Instructions 200947 - Walk Behind Blower WARNING WARNING Wear a face filter mask in dusty conditions to reduce the risk of injury associated with the inhalation of dust. Spark from a removed spark plug wire can result in fire or electrical shock. When servicing the engine: WARNING Disconnect the spark plug wire and place it where it cannot contact the plug or any other metal object. Check the work area before each use.
Important Safety Instructions 200947 - Walk Behind Blower – DO NOT pump gasoline directly into the blower at the gas station. Always use an approved fuel container to transfer the fuel to the gasoline tank. WARNING Rapid retraction of the starter cord will pull hand and arm towards the engine faster than you can let go. Unintentional startup can result in entanglement, traumatic amputation or laceration. Broken bones, fractures, bruises or sprains could result. – DO NOT overfill the gasoline tank.
Important Safety Instructions 200947 - Walk Behind Blower Safety And Dataplate Labels/Tags These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement. D E F C G A B Front view Back view LABEL DESCRIPTION LPN A 2233-L-SF 50 ft. 15m Rev 55 x 177.
Important Safety Instructions 200947 - Walk Behind Blower DESCRIPTION 1966-L-SF-A LABEL WARNING DO NOT TOUCH! Hot surface. ADVERTENCIA D Hot Surface Warning Label ¡NO TOCAR! Superficie caliente. AVERTISSEMENT NE TOUCHEZ PAS! Surface chaude.
Important Safety Instructions 200947 - Walk Behind Blower Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYMBOL MEANING Read Operator’s Manual. To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Important Safety Instructions 200947 - Walk Behind Blower SYMBOL MEANING Amputation Hazard. Rotating parts can entangle hands, feet, hair, clothing and/or accessories. Traumatic amputation or severe laceration can result. Toxic Fumes. The engine exhaust from this product contains chemicals known to the state of California to cause cancer and birth defects and other reproductive harm. Risk of Asphyxiation. This engine emits carbon monoxide, an odorless, colorless poison gas.
Important Safety Instructions 200947 - Walk Behind Blower Operation Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.
Controls and Features 200947 - Walk Behind Blower CONTROLS AND FEATURES Read this operator’s manual before operating your blower. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. 1 2 12 11 1 10 3 4 2 5 3 4 6 10 5 9 6 9 7 7 8 8 Blower Engine 1. Upper Handle 1. Muffler 9. Engine OFF Switch 2. Throttle/Speed Control 2. Air Filter 10. Fuel Tank 3. Handle Adjust Lever 3. Oil Fill Cap/Dipstick 11. Fuel Gauge 4.
Controls and Features 200947 - Walk Behind Blower Parts Included Part Part Qty. Front wheel Upper handle Throttle control 1 1 Hardware Needed Hardware Qty. M8x20 Hexagon bolt 4 Spring washer 4 Flat washer 4 M8 Nylon flange lock nut 1 M6x70 carriage bolt 1 Hardware Reference Tool Needed 13mm Wrench 13mm Wrench 10mm Wrench 1 M6 Nylon flange lock nut 1 Forward flow air attachment 1 N/A Engine Oil 16.9 fl.
Assembly 200947 - Walk Behind Blower ASSEMBLY Your blower requires some assembly. This unit ships from the factory without oil. It must be properly serviced with fuel and oil before operation. For questions regarding the assembly of your blower, call our help line at 1-877-338-0999. Please have your serial number and model number available. Remove the Blower from the Shipping Carton 1. Set the shipping carton on a solid, flat surface. 2. Remove all contents from the carton.
Operation 200947 - Walk Behind Blower OPERATION NOTICE Add Engine Oil Once oil has been added, a visual check should show oil about 1-2 threads from running out of the fill hole. If using the dipstick to check oil level, DO NOT screw in the dipstick while checking. CAUTION DO NOT attempt to crank or start the engine before it has been properly filled with the recommended type and amount of oil. Damage to the engine as a result of failure to follow these instructions will void your warranty.
Operation 200947 - Walk Behind Blower Add Fuel CAUTION Use regular unleaded gasoline with a minimum octane rating of 85 and an ethanol content of less than 10% by volume. DO NOT light or smoke cigarettes. DO NOT mix oil and gasoline. DO NOT overfill the tank. Fill tank to approximately ¼ in. (6.4 mm) below the top of the tank to allow for gasoline expansion. 5. The approximate fuel level is shown on the fuel gauge on top of the fuel tank.
Operation 200947 - Walk Behind Blower NOTICE DANGER The blower engine exhaust contains carbon monoxide, a colorless, odorless, poison gas. Breathing carbon monoxide will cause nausea, dizziness, fainting or death. If you start to feel dizzy or weak, get to fresh air immediately. In some State and local jurisdictions, operate power equipment during reasonable hours to comply with local noise ordinances. For more information, contact your State and local government for specific requirements.
Operation 200947 - Walk Behind Blower Stopping the Engine 5. Pull the starter cord slowly until resistance is felt and then pull rapidly. In an emergency, turn the engine switch to the “OFF” position. 6. As engine warms up, move the choke lever to the “RUN” position. NOTICE If the engine does not stop when the engine switch is moved to the “STOP” position, move the throttle to the slow speed position and slide the choke lever to the cold start (closed) position. Under normal operation: CHOKE 1.
Operation 200947 - Walk Behind Blower Blower Operation 2. Move the handle to the desired height for user comfort. WARNING Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries. Before Each Use Inspect the Blower 1. Always make sure the spark plug wire has been disconnected and engine has been grounded. 2.
Operation 200947 - Walk Behind Blower Vertical Air Flow Adjustment 4. Slide the attachment over the discharge chute. The slot on the top of the attachment will mate with the bolt of the attachment knob. The blower is equipped with an adjustable vertical air flow louver. The vertical air flow can be adjusted to 3 positions: Straight (level), 15 degrees up and 15 degrees down. 5. Hand-tighten the attachment knob to secure the attachment. 1. Stop the engine (see Stopping the Engine section) 2.
Maintenance 200947 - Walk Behind Blower Front Wheel Swivel alternative main jet and installation instructions can be obtained by contacting our Technical Support Team. Installation instructions are also available in the Technical Bulletin area of the CPE website. This blower has a multi-function front wheel that can be locked in the front facing position or unlocked to swivel.
Maintenance 200947 - Walk Behind Blower 4. Tighten dipstick securely. WARNING Before inspecting, cleaning, or servicing the blower, shut off the engine. Wait for all moving parts to stop, disconnect spark plug wire and move it away from the spark plug. Failure to follow these instructions could result in personal injury or damage to the blower.
Maintenance 200947 - Walk Behind Blower 4. Make certain the spark plug gap is 0.028-0.031 in. (0.7-0.8 mm). SPARK PLUG GAP 5. Refer to the spark plug types in Specifications when replacing the plug. 6. Firmly re-install the plug. 7. Attach the spark plug cable to the spark plug. 3. Allow the oil to drain completely into an appropriate container. Cleaning the Air Filter 4. Replace the oil drain plug. 1.
Storage 200947 - Walk Behind Blower 4. Carefully remove the carbon deposits from the spark arrester screen with a wire brush. Service your blower more frequently when operating in adverse conditions. 5. Replace the spark arrester if it is damaged. Contact our Technical Support Team at 1-877-338-0999 to locate the nearest CPE certified service dealer for your blower or engine maintenance needs. 6. Position the spark arrestor on the muffler and attach with the screws removed in step 2.
Storage 200947 - Walk Behind Blower 3. To extend the fuel storage life add a properly formulated fuel stabilizer to the tank. NOTICE The engine works well with 10% or less ethanol blend fuels. When using blended fuels, there are some issues worth noting: 4. Ensure the fuel valve is in the “OFF” position. Long Term Engine Storage (30 Days – 1 Year) – Ethanol-gasoline blends can absorb more water than gasoline alone. 1. Add a properly formulated fuel stabilizer to the tank.
Specifications 200947 - Walk Behind Blower SPECIFICATIONS Oil Specifications NOTICE Blower Specifications Temperature will affect engine oil and engine performance. Change the type of engine oil used based on temperature shown in the “Recommended Engine Oil Type” table. Model........................................................ 200947 Air Velocity*............................ Max 160 MPH (257.5 km/h) ............................................... Max 1300 CFM (ft3/min) Sound Pressure............
Specifications 200947 - Walk Behind Blower 20 19 7 1 2 3 4 17 14 5 15 6 16 4 13 8 9 18 10 22 11 12 13 Figure A 8 4 24 21 8 4 23 Parts Diagram - Figure A 27
Specifications 200947 - Walk Behind Blower Parts List - Figure A # Part Number Description Qty. 1 2550011234 Hex Screw 6 × 12 6 2 2540006536 Fan Guard 1 3 2550011227 Bolt 5/16-24UNF-12.9 1 4 2550000883 Lock Washer Ø8 11 5 2540006540 Impeller Assembly 1 6 2550001644 Hex bolt 8 × 25 4 7 2560004102 Bushing 1 8 2550011239 Washer Ø8 10 9 2540006548 Subplate 1 10 2540006535 Volute Assembly 1 11 2550011339 Flat Key 4.
Specifications 200947 - Walk Behind Blower Parts Diagram - Figure B Figure B 38 1 2 3 4 5 6 7 8 9 10 20 23 15 2 21 22 11 24 21 12 25 26 27 14 28 29 30 21 24 13 14 18 16 17 19 37 23 31 32 35 21 21 36 24 19 33 24 23 34 29 23
Specifications 200947 - Walk Behind Blower Parts List - Figure B # Part Number Description Qty. # Part Number Description 1 2550011243 Locknut M6 1 2 2550002033 Washer Ø6 3 3 2540006550 Throttle Control Assembly 4 2550011246 5 35 2540006542 Front Wheel Connecting Mount 1 1 36 2540006541 Front Wheel Assembly, 8in.
68 94 102 101 70 69 59 74 60 61 73 62 72 71 63 64 66 95 65 38 34 41 99 40 67 37 36 39 55 56 57 54 96 83 84 82 35 96 81 34 79 80 96 96 100 58 46 42 43 45 100 78 77 76 75 47 98 94 97 44 96 48 49 51 93 50 91 89 90 88 52 92 53 86 87 85 200947 - Walk Behind Blower Specifications Engine Parts Diagram
Specifications 200947 - Walk Behind Blower Engine Parts List # Part Number Description 1 12410-Z440110-0001 Cylinder Head Cover Subassembly, Blue White Zinc 12004-Z440110-00A0 Cylinder Head Cover Gasket 2 Qty. 1 1 3 14314-Z010110-0000 Valve Adjusting Nut 2 4 14311-Z010110-0000 Valve Rocker 2 5 14313-Z010110-0000 Valve Adjusting Bolt 2 # Part Number Description Qty. 31 90408-Z010110-0000 Washer, Ø10 × Ø15.8 × 1.5 2 32 11007-Z010110-0001 Drain Plug Bolt, M10 x1.
Specifications 200947 - Walk Behind Blower # Part Number Description Qty. # Part Number Description 60 16002-Z010110-0000 61 Qty. Carburetor Insulator Gasket 1 91 90686-Z010710-00M1 Fuel Pipe, Ø4.5 × Ø8.5 × 160 1 16003-Z010110-0000 Carburetor Insulator Plate 1 92 30431-Z010110-0003 Rubber Jacket, Ø9.5 × Ø11 × 90, Black 1 62 16001-Z010110-0000 Carburetor Gasket 1 93 90685-Z030610-01A1 Clamp, Ø8 × 7 × 0.
Troubleshooting 200947 - Walk Behind Blower TROUBLESHOOTING Problem Engine does not start Cause Solution Spark plug wire disconnected. Reconnect wire. Engine Throttle Control Lever incorrectly set. Put lever in START position. Fuel tank empty. Add fuel. Choke control (if so equipped) in incorrect Move to CHOKE position. position. Stale gasoline. Drain fuel and add fresh fuel.
WARRANTY* Other Exclusions CHAMPION POWER EQUIPMENT This warranty excludes: 2 YEAR LIMITED WARRANTY – Cosmetic defects such as paint, decals, etc. Warranty Qualifications – Wear items such as starter pulleys, starter ropes, filter elements, belts, blower fans, impeller blades, blower and/or vacuum tubes, vacuum bag and straps (where applicable), etc. To register your product for warranty and FREE lifetime call center technical support please visit: https://www.championpowerequipment.
CHAMPION POWER EQUIPMENT, INC. (CPE), THE UNITED STATES ENVIRONMENTAL PROTECTION AGENCY (U.S. EPA) AND THE CALIFORNIA AIR RESOURCES BOARD (CARB) EMISSION CONTROL SYSTEM WARRANTY Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB) emissions regulations.
EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (SORE) (for other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter. 2.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the engine) Systems covered by this warranty Parts Description Fuel Metering System Fuel regulator, Carburetor and internal parts Air Induction System Air cleaner, Intake manifold Ignition System Spark plug and parts, Magneto ignition system Exhaust System Exhaust manifold, catalytic converter Miscellaneous Parts Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed systems.
