INSTALLATION MANUAL AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLERTM MODULE All aXis Controller™ Models REGISTER YOUR PRODUCT ONLINE at championpowerequipment.com or visit championpowerequipment.com READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do so could result in serious injury. This manual should remain with the product.
TABLE OF CONTENTS AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE TABLE OF CONTENTS Installation ......................................... ......... 10 Low Voltage Control Relays ............................ ......... 10 Introduction ................................................... 3 Settings on the aXis ControllerTM Module .......................11 Safety Definitions .......................................... 3 WIFI Setup Method ..............................................
INTRODUCTION AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE INTRODUCTION SAFETY DEFINITIONS Congratulations on your purchase of a Champion Power Equipment (CPE) product. CPE designs, builds, and supports all of our products to strict specifications and guidelines. With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying service. The purpose of safety symbols is to attract your attention to possible dangers.
IMPORTANT SAFETY INSTRUCTIONS AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE Before Installation IMPORTANT SAFETY INSTRUCTIONS WARNING WARNING Per OSHA 3120 Publication; “lockout/tagout” refers to specific practices and procedures to safeguard individuals from the unexpected energization or startup of machinery and equipment, or the release of hazardous energy during installation, service or maintenance activities. Cancer and Reproductive Harm - www.P65Warnings.ca.
IMPORTANT SAFETY INSTRUCTIONS AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE Safety Labels These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement. DESCRIPTION PART NUMBER Alternate Power Source 1681-T-OP (2 per unit) Loose in IM bag. Caution. Overcurrent device. 1943-L-PR Danger. Electrocution shock hazard. Warning. More than one live circuit.
IMPORTANT SAFETY INSTRUCTIONS AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product. SYMBOL MEANING Read Installation Manual. To reduce the risk of injury, user must read and understand installation manual before using this product. Ground.
CONTROLS AND FEATURES AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE CONTROLS AND FEATURES Read this installation manual before installing your transfer switch. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference. Champion Automatic Transfer Switch with aXis ControllerTM Module Models 102006/102008/102009 1 2 11 11 12 3 Models 102007/102010 10 9 4 8 11 11 5 6 7 14 1. aXis Controller 8.
UNPACKING AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE UNPACKING Electrical Grommet(s) Grommets can be used in any enclosure knockout for NEMA 1 installations. Grommets can only be used in the bottom enclosure knockouts for NEMA 3R installations, when installed outside. 1. Use care when unpacking to avoid damaging transfer switch components. 2. Allow the ATS to acclimate to room temperature for a minimum of 24 hours before unpacking to prevent condensation on the electrical apparatus.
UNPACKING AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE 6. Connect Generator L1-L2 to Generator side breaker. Torque to 45-50 in-lbs. Wiring the ATS NOTICE 7. Connect Generator Neutral to neutral bar. Torque to 275 in-lbs. US ATS model shown for reference. For Canadian installation, refer to ATS Installation Manual. 8. Connect Generator Ground to ground bar. Torque to 35-45 in-lbs.
INSTALLATION AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE Battery Charger Wiring Utility Sensing Fuse Block The aXis Controller™ HSB contains a 24V battery charger that is powered by 120V AC. The battery charger receives 120V AC power from the aXis Controller™ ATS using the single fuse block located in the bottom left corner of the ATS. The utility sensing fuse block is not used in a typical installation.
INSTALLATION AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE – Off= All managed loads will be turned off when if the HSB frequency drops below 57 Hz. Settings on the aXis ControllerTM Module 1. On the aXis control board, set the two circular pots that are located to the right of the DIP switches to match the maximum power output of the generator for your fuel type. Switch 6. Spare. Not used at this time. Switch position does not matter. Switch 7.
INSTALLATION AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE WIFI Setup Method 5. Set the HSB exercise frequency and schedule. Confirm and Save the settings before continuing. 1. Use a WiFi enabled device (laptop, smart phone, tablet, etc.) in near proximity to the ATS. 2. Search and Connect to network name (SSID) “Champion XXXX” where XXXX will match the last four digits of the serial number that is printed on the control board.
INSTALLATION AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE Full System Check Connecting the Load Management Systems The following instructions pertain only to aXis Controller Load Management Modules (LMM) that use Power Line Carrier (PLC) communication. If one or more LMM’s are being installed on the home, install them per the installation instructions included with the LMM before continuing. 1. Open Utility breaker for full system test, close breaker after confirming all systems working.
SPECIFICATIONS AUTOMATIC TRANSFER SWITCH WITH aXis CONTROLLER™ MODULE SPECIFICATIONS Model 102006 102007 102008 Enclosure Style 102010 NEMA 3R Outdoor Maximum Amps 200 150 Nominal Volts ETL Listed 102009 100 120/240 UL STD NO. 1008 CSA STD C22.2 No. 178.1 Load Management Circuits UL STD NO. 1008 CSA STD C22.2 No. 178.1 4 Weight 43 lbs (19.6 kg) Height 28 in. (710 mm) Width 20 in. (507 mm) Depth 8.3 in.
WARRANTY* Other Exclusions CHAMPION POWER EQUIPMENT This warranty excludes: 2 YEAR LIMITED WARRANTY – Cosmetic defects such as paint, decals, etc. – Wear items such as filter elements, o-rings, etc. Warranty Qualifications – Accessory parts such as storage covers. To register your product for warranty and FREE lifetime call center technical support please visit: https://www.championpowerequipment.
