VERTICAL/HORIZONTAL LOG SPLITTERS 22, 28 & 35 TON MODELS MODEL NUMBERS 1032822, 2152374 and 1083946 Owner’s Manual ASSEMBLY & OPERATING INSTRUCTIONS WARNING: All operators must read this manual before operating this log splitter. Follow the safety instructions in the manual and in decals attached to the product. Failure to do so could result in serious injury or death.
Table of Contents Page(s) Important Safety Information................................................................................................................. Intended Use ....................................................................................................................................... 1-4 Personal Protective Equipment ............................................................................................... 1 Safety Decals ..................
WARNING: Read and thoroughly understand all instructions in this manual and on safety decals before assembling or operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you have any questions concerning safe operation.
PART NUMBER: S52062200 LOCATION: TOP OF CYLINDER PART NUMBER: S52062300 LOCATION: STRIPPER PLATE, OPERATOR SIDE PART NUMBER: S52062600 LOCATION: STRIPPER PLATE, NON OPERATOR SIDE PART NUMBER: S52062400 LOCATION: HYDRAULIC TANK LOWER TANK, RIGHT CORNER PART NUMBER: S52062100 LOCATION: TOP OF HYDRAULIC CYLINDER Page 2
GENERAL SAFETY • • • • • • ALWAYS keep the operator’s manual nearby for reference. Reread the manual periodically. ALWAYS keep all bystanders and pets a minimum of 10 feet away from your work area when operating this log splitter. Only the operator is to be near the log splitter during use. NEVER allow adults lacking proper instructions and understanding to operate this log splitter. NEVER actuate the control unit until all people are clear of the work area.
. • • • ALWAYS periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tight. ALWAYS replace all damaged or worn parts immediately. ALWAYS be sure that all replacement parts meet manufacturer’s specifications. MAINTENANCE & SAFETY • The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic components.
ASSEMBLY INSTRUCTIONS NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become necessary to disassemble the unit for repair or replacement of parts. The drawings in this manual are for reference only. Some of the components on your log splitter may look slightly different. 5 ITEM NO. DESCRIPTION QTY.
STEP 3: Attach the tongue assembly (5) to the tank assembly (1) using two 1/2” NC x 4-1/2” hex cap bolts (2), two 1/2” lock washers (3) and two 1/2” hex nuts (4). Tighten. ITEM NO. DESCRIPTION QTY. 1 2 3 4 5 Tank Assembly 1/2” NC x 4-1/2 Hex Bolt 1/2” Lock Washer 1/2” NC Hex Nut Tongue Assembly 1 2 2 2 1 STEP 4: Stand the beam (1) up on end. Two people may be needed for this step to ensure safety. Make sure that the beam is stable and on a level surface.
STEP 5: Connect the end of the 1/2” ID x 38” hydraulic pressure hose (1) coming from the fitting on the pump to the fitting on the valve. See illustrations below. STEP 6: Slide one hose clamp on the end of the 3/4” x 56” hydraulic return hose (2) that comes from the fitting on the filter. Then connect the hose to the fitting on the valve.Tighten hose clamp. See illustrations below. Area of Detail DETAIL A SCALE 1:3 ITEM NO. . 1 2 3 DESCRIPTION QTY.
REPLACEMENT PARTS TANK/ENGINE ASSEMBLY BREAKDOWN dĂŶŬ Θ ŶŐŝŶĞ ƐƐĞŵďůLJ WĂƌƚƐ >ŝƐƚ /ƚĞŵ EŽ͗ ϮϮd WĂƌƚ EŽ͘ Ϯϴd WĂƌƚ EŽ͘ ϯϱd WĂƌƚ EŽ͘ ĞƐĐƌŝƉƚŝŽŶ ^ϰϬϭϭϴϴϬϬ ϭ dĂŶŬ ^ϬϳϭϬϮϮt Ϯ WŝǀŽƚ WŝŶ ^ϬϳϬϵϮϰϬϬ ϯ ϭͬϮŝŶ dž ϯͬϰŝŶ ,ĂŝƌƉŝŶ ŽƚƚĞƌ WŝŶ ^ĞĞ ĞůŽǁ ϰ ŶŐŝŶĞ Θ WƵŵƉ ƐƐĞŵďůLJ ^ϭϳϬϱϱϬϬϬ ϱ ϱͬϭϲŝŶ dž ϭͲϭͬϮŝŶ 'ϱ ,Ğdž Žůƚ ^ϭϳϬϰϬϴϬϬ ϲ ϱͬϭϲŝŶ &ůĂƚ tĂƐŚĞƌ ^ϭϳϬϮϬϳϬϬ ϳ ϱͬϭϲͲϭϴ hE ELJůŽĐŬ EƵƚ ^ϯϵϬϯϰϵϬϬ ϴ ϯͬϰŝŶ ,Ğdž EŝƉƉůĞ ^ϯϵϬϲϬϰϬϬ ϵ &ŝůƚĞƌ ƐƐĞŵďůLJ ϭϬ ϯͬϰŝŶ EWd dž ϯͬϰŝŶ dƵďĞ ϵϬͲĚĞŐ ^ϯϵϬϯϮϬϬϬ ϭϭ ϯͬϰEWd ƚŽ ϯͬϰŝŶ / dƵďĞ &ŝƚƚŝŶŐ ^ϯϵϬϯϴϯ
BEAM ASSEMBLY BREAKDOWN ĞĂŵ ƐƐĞŵďůLJ WĂƌƚƐ >ŝƐƚ /ƚĞŵ EŽ͗ ϮϮd WĂƌƚ EŽ͘ Ϯϴd WĂƌƚ EŽ͘ ϯϱd WĂƌƚ EŽ͘ ĞƐĐƌŝƉƚŝŽŶ ϭ ϭͬϮŝŶ ,Ğdž EƵƚ ^ϭϳϬϭϬϱϬϬ ^ϭϳϬϯϬϯϬϬ Ϯ ϭͬϮŝŶ >ŽĐŬ tĂƐŚĞƌ ^ϭϳϬϳϭϲϬϬ ϯ ϭͬϮŝŶ dž ϯŝŶ ,Ğdž Žůƚ ϯ ^ϭϳϬϱϲϲϬϬ ϭͬϮŝŶ dž ϯͲϭͬϰŝŶ ,Ğdž Žůƚ ^ϰϬϭϰϭϳϬϬ ϰ ϮϮd Θ Ϯϴd tĞĚŐĞ ϰ ^ϰϬϭϰϭϴϬϬ ϯϱd tĞĚŐĞ ^ϯϵϬϯϮϬϬϬ ϱ ϯͬϰŝŶ EWd dž ϯͬϰŝŶ dƵďĞ &ŝƚƚŝŶŐ ^ϯϵϬϯϰϯϬϬ ϲ ϭͬϮŝŶ EWd dž ϭͬϮŝŶ EWd EŝƉƉůĞ ^ϯϵϬϰϳϭϬϬ ϳ sĂůǀĞ ,ĂŶĚůĞ <ŝƚ ^ϯϵϬϰϬϲ^t, ϴ ƵƚŽͲZĞƚƵƌŶ sĂůǀĞ ^ϯϵϬϯϵϬϬϬ ϵ ϰϱͲĚĞŐ ^ǁŝǀĞů &ŝƚƚŝŶŐ ^ϯϵϬϯϰϳϬϬ ϭϬ ϭͬϮŝŶ EWd ƚŽ ^ƚĞĞů dƵďĞ &ŝƚƚŝŶŐ ϭϭ
TONGUE ASSEMBLY BREAKDOWN /ƚĞŵ EŽ͗ ϭ Ϯ ϯ ϰ ϱ ϲ ϳ ϴ ϵ ϭϬ ϭϭ ϮϮd dŽŶŐƵĞ ƐƐĞŵďůLJ WĂƌƚƐ >ŝƐƚ WĂƌƚ EŽ͘ ĞƐĐƌŝƉƚŝŽŶ ϱϲϱϮϴϰ DϭϬ dž ϭ͘ϱ ELJůŽĐŬ EƵƚ ϱϲϰϳϴϭ dŽŶŐƵĞ tĞůĚŵĞŶƚ ^ϰϬϭϮϲϬϬϬ 'ƌŽƵŶĚ ^ƚĂŶĚ ^ϬϳϬϵϱϴϬϬ ϱͬϭϲŝŶ dž ϯͲϭͬϰŝŶ ^ƋƵĂƌĞ >ŽĐŬ WŝŶ ^ϰϬϬϯϰϲϬϬ ,ŝƚĐŚ Ăůů ƐƐĞŵďůLJ ^ϰϬϬϯϮϯϬϬ ϮϬ >ŝŶŬ ŚĂŝŶ ǁͬ,ŽŽŬ ϱϲϱϮϳϱ DϭϬ dž ϭ͘ϱ dž ϭϬϬŵŵ 'ϱ Žůƚ ϱϲϱϮϳϲ DϭϬ dž ϭ͘ϱ dž ϭϮϬŵŵ 'ϱ Žůƚ ϱϲϱϮϳϳ DϭϬ dž ϭ͘ϱ dž ϵϬϬŵŵ 'ϱ Žůƚ ϱϲϱϮϴϲ DϭϬ &ůĂƚ tĂƐŚĞƌ ϱϲϰϳϰϯ ^ƚĂďŝůŝnjĞƌ WŝŶ ƐƐĞŵďůLJ YƚLJ ϯ ϭ ϭ ϭ ϭ Ϯ ϭ ϭ ϭ Ϯ ϭ /ƚĞŵ EŽ͗ ϭ Ϯ ϯ ϰ ϱ ϲ ϳ ϴ /ƚĞŵ EŽ͗ ϭ Ϯ ϯ
OPERATING INSTRUCTIONS WARNING: Read and thoroughly understand all instructions and safety information before operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment, a log splitter can be dangerous if assembled or used improperly. Do not operate this log splitter if you have doubts or questions concerning safe operation.
STARTING INSTRUCTIONS (Honda GC190) NOTE: REFER TO HONDA ENGINE OWNER’S MANUAL FOR COMPLETE INFORMATION ON STARTING, MAINTENANCE AND TROUBLE-SHOOTING. To Start a Cold Engine 1) Turn the fuel valve to the ON position. 2) Move the choke to the ON position. 3) Move the throttle control to the FAST position. 4) Pull the starter grip lightly until resistance is felt. Then pull rapidly to start engine.
TOWING This log splitter is equipped with pneumatic tires, a Class I coupler (2 in. diameter ball required) and safety chains. Before towing, the safety chains must be secured to the hitch or bumper of the vehicle. Local regulations should be checked regarding licensing, lights, towing, etc.Turn fuel shut off valve on the engine to the “Off” position prior to towing. Failure to do so may result in flooding the engine. Do not exceed 45 mph when towing this log splitter.
SPECIFICATIONS Model No. 1032822 Model No. 2152374 Model No. 1083946 Engine Kohler SH265 6.5 HP Kohler CH395 9.5 HP Pump Two-Stage 11 GPM Kohler CH270 7 HP Honda GC190 Two-Stage 11 GPM Cylinder 4 in. Diam. x 24 in. Stroke 4-1/2 in. Diam. x 24 in. Stroke 5 in. Diam. x 24 in.Stroke Valve Auto-Return Auto-Return Auto-Return Maximum Splitting Force* 22 Tons 28 Tons 35 Tons Maximum Log Length 25-1/2 in. 25-1/2 in. 25-1/2 in. Cycle Time* 13 Seconds 17 Seconds 14 Seconds Wheels 4.
