Installation Manual with Service Replacement Parts Circular Conveyor Table Models: CCT 90 90° Table CCT 180 180° Table CCT 90 CCT 180 Issue Date: 3.14.11 Manual P/N 114592 rev. C 3765 Champion Boulevard, Winston-Salem, NC 27105 336/661-1556 Fax: 336/661-1660 Toll-free: 800.858.4477 2674 N. Service Road, Jordan Station Ontario, Canada L0R 1S0 905/562-4195 Fax: 905/562-4618 Toll-free: 800.263.
For future reference, record your dishwasher information in the box below.
In Canada you can Register by Postage Paid Mail: Cut along the dashed lines, then complete the back of the postage paid card above and mail immediately to validate your machine warranty. OR REGISTER YOUR PRODUCT ONLINE Make sure you are connected to the internet then click or enter the address below. In the U.S.A http://www.championindustries.com/register In Canada http://www.championindustries.
PRODUCT REGISTRATION CARD Serial # Model Date of Installation: Company Name: Address: Telephone #: ( ) --- (Street) Province Postal Code Contact: Installation Company: Address: Telephone #: Contact: FAILURE TO REGISTER YOUR PRODUCT MAY VOID YOUR WARRANTY IMPORTANT IMPORTANT REGISTER YOUR PRODUCT ONLINE Make sure you are connected to the internet then click or enter the address below. In the U.S.A http://www.championindustries.com/register In Canada http://www.championindustries.
Revision History Revision History The Revision History can contain part number changes, new instructions, or information that was not available at print time. • We reserve the right to make changes to these instructions without notice and without incurring any liability by making the changes.. • Equipment owners may request a revised manual, at no charge, by calling 1 (800) 858-4477 in the USA or by calling 1 (800) 263-5798 in Canada.
Limited Warranty LIMITED WARRANTY Champion Industries Inc. (herein referred to as Champion), 3765 Champion Blvd., Winston-Salem, North Carolina 27105, and P.O. Box 301, 2674 N. Service Road, Jordan Station, Canada, L0R 1S0, warrants machines, and parts, as set out below.
Table of Contents Table of Contents CCT90, CCT180 Circular Conveyor Table Revision History........................................................................................................ i Limited Warranty....................................................................................................... ii Model Descriptions.................................................................................................... iv Installation .......................................................
Model Descriptions Model Descriptions CCT 90 90° Circular Conveyor Table designed to move dish racks exiting the rack conveyor dishwasher. The CCT 90 captures the dish racks, moves them forward and out of the dish washer. The dish rack is rotated 90° as it moves along the table. The CCT 90 is most often connected to a dish table or roller conveyor. The CCT 90 reduces the dishwasher footprint to save space in the dish room.
CCT 90, CCT 180 - Installation Receiving NOTE: The installation of your dishwasher must be performed by qualified service personnel. Problems due to improper installation are not covered by the Warranty. 1. Inspect the outside of the Conveyor pallet for signs of damage. 2. inspect the Conveyor for damage. 3. Check for any accessories that may have shipped with your dishwasher. 4. Turn to the front of this manual and complete the warranty card.
Installation - CCT 90, CCT 180 Mechanical Connections and Conveyor Adjustments CCT 90 and CCT180 Refer to the illustration on the next page and follow the installation instructions below. 1. Manually advance the dishwasher cradle assembly to its maximum forward stroke. 2. Remove parts A, B, C, and D from the CCT. Save the fasteners. 3. Position the CCT against the discharge end of the dishwasher. 4. Reinstall part C on the CCT. 5.
CCT 90, CCT 180 - Installation Mechanical Connections and Conveyor Adjustments CCT 90 and CCT180 A F B B C D G E CCT 90 Left-Right Installation Shown E E 3
Blank Page This Page Intentionally Left Blank 4
Service Replacement Parts Service Replacement Parts Illustrations Page Table Assembly - CCT90......................................................................................................................................... 6 Table Assembly - CCT180....................................................................................................................................... 8 Cradle and Drive Assembly - CCT90, CCT180......................................................................
Table Assembly - CCT90 7 6 1 7 6 2 5 4 16 17 19 20 3 9 16 16 7 6 13 5 11 12 14 1 5 6 5 8 6 16 18 17 3 8 15 7 22 10 6 21 22 21 23 21 24 25 26 24 23 22 24 6 18
CCT90 - Table Assembly Item No. Part No. Description Qty. 1 332857 RACK GUIDE, UNLOAD END CCT 2 2 332838 RACK SUPPORT, ROD WELDMENT OUTER 1 3 100097 SCREW, TRUSS HD. 10-32 X1/2" SST 4 4 332876 U-CLIP, CCT W/EXT FRONT FLANGE 1 5 102376 WASHER, FLAT, 5/16" SST 7 6 106482 WASHER, LOCK, 1/4" SPLIT SST 9 7 106014 HEX ACORN, PLAN NUT, 1/4-20 SST 6 8 100736 BOLT, HEX HD.
Table Assembly - CCT180 1 2 3 11 3 12 13 7 5 4 8 9 14 6 13 7 13 6 15 18 10 6 5 6 6 18 11 5 17 6 5 12 19 22 25 22 26 23 27 23 24 27 25 27 21 20 13 7 22 8 6 7 15 16 5 17
CCT180 - Table Assembly Item No. Part No. Description Qty. 1 332839 ROD, RACK SUPPORT, OUTER CCT180 1 2 332919 TRACK, INNER ,CCT 180 1 3 206945 PIN, INNER RACK SUPPORT 2 4 107967 NUT, GRIP 1/4-20, W/NYLON INSERT 1 5 102376 WASHER, FLAT, 5/16, SST 13 6 106482 WASHER, LOCK 1/4 SPLIT, SST 18 7 100736 BOLT, HEX HD.,1/4-20 X 3/4" 13 8 304816 STRAINER, DRAIN 1 9 107342 BASKET, STRAINER, METAL 1 10 332876 U-CLIP, CCT W/EXT.
Cradle and Drive Assembly - CCT90, CCT180 3 4 23 22 5 21 6 26 25 7 2 8 3 9 10 4 11 5 6 11 12 14 13 14 12 14 13 12 15 16 17 18 12 11 17 19 10 24 20 11 27
CCT90, CCT180 - Cradle and Drive Assembly Item No. Part No. Description Qty. 1 332883 CRADLE, CCT 90 (Metal frame only) 1 2 332906 CRADLE, CCT 180 (Metal frame only) 1 3 100746 BOLT, HEX HD. 3/8-16 X 1-1/4" SST 2 4 113860 BEARING AND HOUSING ASSEMBLY 1 5 106407 WASHER, LOCK 3/8" SPLIT, SST 2 6 109010 NUT, GRIP 3/8" W/NYLON INSERT, SST 2 7 206939 SHAFT, PIVOT 1 8 314351 STIFFENER, SHAFT 1 9 107589 WASHER, LOCK 1/2" SPLIT SST 1 10 100747 BOLT, HEX HD.
Blank Page This Page Intentionally Left Blank 12
