Specifications

ManualsBrandsChampion ManualsFanRM401A

Circle the model of your cooler and

record the serial number below.

Read Carefully All Of This Manual

Before Installing The Unit.

Encierre con un circulo el modelo de su

enfriador y escribe el número de serie abajo.

Lea Con Cuidado Todo Este Manual Antes

De Instalar La Unidad.

Serial #

Número De Serie

Read And Save These Instructions

Evaporative Cooling

Evaporative cooling is nature’s way of cooling. When air is moved

over a wet surface, water is evaporated and heat is absorbed. When

stepping out of a swimming pool with the wind blowing, evaporative

cooling makes you feel cool, even though the air may be warm.

The human body itself is cooled primarily by the evaporation of

perspiration.

This unit works on the same principle. Air is drawn across wet

ﬁ lter pads where the air is cooled by evaporation and then circulated

throughout the building. It is this combination of cooled air and the

movement of air over the skin which makes it feel cool.

Unlike refrigeration systems which recirculate the air, an evaporative

cooler continually brings in fresh air while exhausting old air. You

are completely replacing the air every 2 to 4 minutes by opening

windows or doors or a combination of both. The air is always fresh,

not stale, laden with smoke and odors as happens with refrigerated

air conditioning.

Vea el Español en el interior

110522-1 1-09www.championcooler.com

MOBILE EVAPORATIVE

COOLER

Manual Control Units

M201A

M301A

M401A

Remote Control Units

RM301A

RM401A

Safety Rules

1. Read these instructions carefully.

2. Unit must be in the Off Position and Unplugged from power

receptacle when installing or performing any maintenance.

3. This cooler will run on 120 volt A.C., 60 Hz (cycle) current

only.

4. Motor and pump are grounded and have an automatic thermal

overload switch which will shut motor off if it overheats. The

motor will restart automatically when it cools down.

5. Pump receptacle is for grounded evaporative cooler pump only.

Do not plug anything else into receptacle.

WARNING: To reduce the risk of ﬁ re or electric shock, do not

use this fan with any “solid-state fan speed control device.”

Summary of content (8 pages)

PAGE 1
MOBILE EVAPORATIVE COOLER Manual Control Units M201A M301A M401A Remote Control Units RM301A RM401A Circle the model of your cooler and record the serial number below. Encierre con un circulo el modelo de su enfriador y escribe el número de serie abajo. Read Carefully All Of This Manual Before Installing The Unit. Serial # Lea Con Cuidado Todo Este Manual Antes De Instalar La Unidad. Número De Serie Read And Save These Instructions Vea el Español en el interior Safety Rules Evaporative Cooling 1.
PAGE 2
Operation Exhaust Air Manual Control Units • Pump setting. The rotary switch has 6 settings. The “Pump” setting will operate the pump without the blower. For best results turn the switch to “Pump” for a few minutes to wet the pads before operating the fan. • High and low cool settings. The “High Cool” and “Low Cool” settings operate both the pump and the blower. Turn the unit to “Low Cool” when possible.
PAGE 3
Note: Do Not Overfill. Fill water to a maximum height of 2 1/2 inches (approximately 1 inch from the top of the bottom pan). If using a garden hose, the float will need to be adjusted to maintain this water level. This can be accomplished by bending the float rod. Nut Float Body Garden Hose Adapter Washer Float Rod Fig. 3 Maintenance WARNING: Before doing any maintenance be sure power is off and unit is unplugged. This is for your safety. Annual Maintenance • Oil bearings.
PAGE 4
Troubleshooting Problem Failure to start or no air delivery Possible Cause 1. No electrical power to unit • Fuse blown • Circuit breaker tripped • Electric cord unplugged or damaged 2. Belt too loose or tight 3. Motor overheated • Belt too tight • Blower bearings dry 4. Motor locked Inadequate air delivery with cooler running 1. Insufficient air exhaust 2. Belt too loose 3. Pads plugged Inadequate cooling 1. Inadequate exhaust in house 2.
PAGE 5
Replacement Parts List / Lista De Piezas De Repuesto When ordering parts, please be sure to furnish the following information on all orders. Failure to do so may delay your order. / Al pedir piezas, incluya toda la información siguiente con su pedido. El no proporcionar toda esta información resultará en una demora. 1. Model number / Modelo 2. Serial number / Número de serie 3. Description and part number / Descripción y número de pieza 4. Date of purchase / Fecha de compra No.
PAGE 6
Parts Drawing / Dibujo De Piezas M201A 6 110522-1
PAGE 7
Parts Drawing / Dibujo De Piezas M301A / RM301A 110522-1 7
PAGE 8
Parts Drawing / Dibujo De Piezas M401A / RM401A Lea y Conserve Estas Instrucciones Reglas De Seguridad 4. El motor y la bomba están conectados con la tierra, y se apagarán automáticamente en caso de sobrecalentamiento. Los motores volverán a funcionar cuando se enfrían. 1. Lea las instrucciones con cuidado. 2. La unidad debe estar Apagada y Desconectada de la electricidad cuando se instale o haga cualquier mantenimiento. 3. Su enfriador funciona sólo con corriente alterna de 120 voltios, 60 Hz.