Wet/Dry Vacuums Operator’s Manual 8 Gallon Model No. VS810WD FOR YOUR SAFETY Read and understand this manual before use Keep this manual for future reference www.channellockproducts.com Part No. VB51BZ.20.96.
TABLE OF CONTENTS SECTION PAGE Warranty…………………………………………………………………………………………...……. 2 Safety Instructions and Warnings……………………………………………………………………. 3 Grounding Instructions…………..……………………………………………………………………. 4 Extension Cord…………………………………………………………………………………………. 4 Unpacking and Checking Carton Contents………….……………………..…………….…………. 5 General Assembly Instructions…………………………………………………………….…………. 6 Dry Vacuum Operation………………………………………………………………………………… 7 Wet Vacuum Operation………………………………………………………………………………..
SAFETY INSTRUCTIONS & WARNINGS IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS VACUUM Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating. Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your Wet/Dry Vac, use only CHANNELLOCKTM recommended accessories.
GROUNDING INSTRUCTIONS This product must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
UNPACKING AND CHECKING CARTON CONTENTS Remove entire contents of carton. Check each item against the carton contents list. Carton Contents List Key Description……………………..…….…QTY A B C D E F G H I J K L M N Vac Assembly……………………………..1 Flex Hose With Air Control Nozzle….......1 2-in 1 Utility Nozzle…………………….....1 Crevice Tool…………………………….....1 Floor Brush/Squeegee……………………1 Extension Wands …………………………2 Cartridge Filter…………………….……...1 Filter Retainer………………………...1 Foam Sleeve Filter ….……….….…….....
GENERAL ASSEMBLY INSTRUCTIONS A Philips head screw driver is required for assembly. WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY 1. Verify that the power cord is disconnected from the outlet. (fig.1) 2. Undo the latches. (fig.2) 3. Lift the power head off the container. (fig.3) 4. Remove the contents from inside the container, make sure you have all contents as listed on page 6. (fig.
DRY-VACUUM OPERATION DRY VACUUMING WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO; COAL, MAGNESIUM, GRAIN OR GUN POWDER.
WET-VACUUM OPERATION LIQUID VACUUMING WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO; COAL, MAGNESIUM, GRAIN OR GUN POWDER.
BLOWING OPERATION This Wet/Dry Vac has blowing capabilities. To use the blower feature follow the instructions listed. WARNING: ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH ANSI Z87.1 (OR IN CANADA, CSAZ94.3) BEFORE USING BLOWER. WARNING: KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS. WARNING: WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED. 1. 2. 3. 4. Verify that the power cord is disconnected from the outlet. (fig.1) Make sure the container is empty before using as a blower.
NOTICE! The filters included are made of high quality materials designed to stop small dust particles. The cartridge filter should be used for dry pick-up only. A dry cartridge filter is necessary to pick up dust. If the cartridge filter is wet, it will clog quickly and be very difficult to clean. Handle the filter carefully when removing it for cleaning and replacing it. Check the filters for tears or small holes, a small hole can let dust pass through and out of the cleaner.
Cleaning Foam Sleeve Filter 1. With the removed power head in the upside down position, carefully remove foam sleeve filter. (fig.4) 2. Use a mild soap and water solution to wash foam sleeve filter and rinse with clean water. (fig.5) 3. Allow filter to air dry before installing and using again. TROUBLESHOOTING WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE TROUBLESHOOTING Symptom Possible Causes Corrective Action Vacuum will not operate 1) No power supply.
PARTS LIST -EXPLODED VIEW 12
