Networked DVR 16CH/9CH/4CH NW-STA-5016/5009/5004 NW-STA-5016/5009/5004 USER MANUAL Networked DVR Product Feature 1 16/9/4 CH Multiple camera Input 2 Embedded XP O/S of DOM(Disk On Memory) solution Mounted 3 Pentapllex Multi tasking for Monitoring And recording and searching and networking 4 Able to record the CIF size(320*240) video Image at the speed of 120/240/480 fps (frame for second) 5 Large quantity HDD backup function by using IEEE1394 and USB2.
User Manual Contents Chapter 1 Service Requirement 3 Chapter 2 Product Information 4 Chapter 3 Basic Product Operation 6 Chapter 4 System Setup 24 Chapter 5 Firmware Upgrade 49 Chapter 6 Warranty 52 Page: 2 NW-STA-5016/5009/5004 User Manual
User Manual Chapter 1 Service Requirement Limitation of warranty We warrant that DVR series will be free from defects in materials and workmanship under normal use and service for all parts excluding hard drives for a period of one year after the date that the customer purchased the product. If such a defect occurs, you should contact where you purchased and return the product to us accompanied with the proof of purchase, we will either repair or replace the product through our inspection.
User Manual Chapter 2 Product Information z Features Enable integrated video monitoring and system management by networking with maximum 1000DVRs systems through CAMS(Central Automated Monitoring System) interface. High quality video display and system stability through embedded operating system with hardware MPEG4 video compression chip. Support the max D1(720*480) quality resolution video display and 120FPS recording. 4/9/16 CH video input and 4 CH audio input.
User Manual Firmware upgrade using network and USB port. Remote upgrade using CMS Free alarm (max 30secs), port alarm (max 120secs) recording Watermarking Private backup viewer E-Map’s layout mapping able to install maximum 4 HDD to save 2.
User Manual Chapter 3 General product operation Page: 6 NW-STA-5016/5009/5004 User Manual
User Manual FRONT FRONT CASE CASE Button Button Description Description IV-STA-5016 (16ch) SEQ. button Function button Division rotating surveillance button Setup Status, Audio, Backup, P/T/Z, SEQ, Log list SPOT button Menu button Shows the menu, moves to upper menus and complete setup Setup SPOT monitor LED Indicator PTZ. button Indicate present system status information Move button Operates Pan/Tilt camera Moves to setup and menu. Operates PTZ camera Rec.
User Manual FRONT FRONT CASE CASE Button Button Description Description IV-STA-5009 (9ch) SEQ. button Function button Division rotating surveillance button Setup Status, Audio, Backup, P/T/Z, SEQ, Log list SPOT button Menu button Shows the menu, moves to upper menus and complete setup Setup SPOT monitor LED Indicator PTZ. button Indicate present system status information Move button Operates Pan/Tilt camera Moves to setup and menu. Operates PTZ camera Rec.
User Manual FRONT FRONT CASE CASE Button Button Description Description IV-STA-5004 (4ch) Numeric buttons Applies setup details and select channel Rec. button Records images PTZ. button LED Indicator Operates Pan/Tilt camera Indicate present system status information division button 1ch,4ch division button Move button Moves to setup and menu. Operates PTZ camera USB Port: 2 PORT Play forward button CD-ROM Max. x 128 play forward.
User Manual Power on/off zPower on Press the power button at the back to be ‘ON’ to turn it on after connecting the power cable. zPower off ① press ‘Menu’ button [menu Æ system Æ shutdown] ② select ‘Shutdown’ and press ‘Enter’ button. ③ select ‘OK’ button after the message “ system will shutdown”. Press ‘Enter’ button. ④ press the power switch at the back to be ‘Off’. System Login zInput password Input the password using number buttons at the password box. ☞ The default value is ‘0000’.
User Manual Screen display [ Channel status ] Channel number Camera name : Recording : Motion detection in process : Sensor detection in process : Channel sequence indication : PTZ indication [ Playback status ] : : : : : : : : Playback in progress Pause Playback per frame : Play backward per frame Speed playback : Speed play backward Double speed playback Double speed play backward Triple speed playback Triple speed play backward [ Slide bar ] : CMS connection status : USB device connection status Date
User Manual Screen setup z Full screen mode - press this button. - shifts to next channel each time you press this button. z Quad screen mode - press this button. - shifts to the next channel each time you press this button. - If you press a channel number button on remote-controller while being displayed in the current quad screen, the selected channel turns full screen.
User Manual z9 division screen mode press this button z16 division screen mode press this button zPOP screen mode *only for 9Ch & 16Ch products -press ‘POP’ button, it will display a certain channel larger than other channels. zOSD mode - press ‘OSD’ button, icons and channel status phrases will appear or disappear.
User Manual zPIP screen mode You can monitor 2 screens at the same time with small screen inside of one screen. (1) press ‘PIP’ button on the remote controller. (2) press ‘PIP’ button one more time the display channels will be exchanged. 1 2 ‘PIP’ ‘PIP’ Button Button 2 1 (3) If you press a channel number button on the controller, the channel will be displayed in small screen. Ex) 1 1 Cam Cam ‘3’ ‘3’ Button Button 2 3 (4) you can move the small screen using arrow buttons.
User Manual zSPOT screen * only for 9Ch & 16Ch products able to display real time screen of another screen-mode in different monitor using ‘SPOT OUT’ port at the back of product. ▶Press ‘Function’ button and select ‘Spot’ to set up ‘SPOT’ screen. SPOT SINGLE CHANNEL SINGLE CHANNEL SEQ SINGLE SEQ QUAD CH1 (1) type ① single channel ▷playback only one selected channel in full screen mode. SPOT SINGLE CHANNEL CH1 ② sequence single ▷playback each channel in full screen mode in sequence.
User Manual Digital zoom z press Z/F (ZOOM) button in full screen mode to active digital zoom. z zoomed area moves as you press arrow buttons. z size of zoomed area gets bigger and smaller as you press Z/F (ZOOM ) button one more time. z press ‘Enter’ button, it shows the selected area bigger like the images below. Recording z press ‘REC’ button to start recording. Check before recording !! (1) Check if hard disk is formatted. (2) Check the camera output. (3) Check if each channel names are correct.
User Manual Search z press ‘SEARCH’ button. Then you can see the ‘Search’ menu like below. SEARCH SEARCH BY TIME SEARCH BY CALENDAR SEARCH BY EVENT GO TO FIRST GO TO LAST z Search by time (1) input the date and time to search. Press ‘Enter’ button. z Search by calendar (1) you can see ‘calendar’ menu like below if you select ‘Search by calendar’. (2) select the date and time using arrow keys. Press ‘Enter’ button. (3) lastly, select ‘OK’ and press ‘Enter button’.
User Manual z Search by event (1) you can see the menu like below if you select ‘Search by event’. (2) input the beginning date/time and ending date/time to search. (3) select channels to search. (4) select events to search. (5) lastly, select search and press ‘Enter’ button.
User Manual Backup z backup data using USB device. (1) Connect ‘USB’ device to the DVR’s USB port. (2) Press ‘Function’ button and select ‘Backup’ (3) Select options from menu. BACKUP DEVICE FORMAT MEDIA TYPE CHANNEL ALL CH1 CH5 CH9 CH13 CH2 CH6 CH10 CH14 CH3 CH7 CH11 CH15 CH4 CH8 CH12 CH16 FROM TO BACKUP CLOSE 9DEVICE – select the device to backup. 9MEDIA TYPE– select media ‘CD’,’DVD’ etc to backup. 9FORMAT – format the media before backup. 9CHANNEL – select channels to backup.
User Manual z Backup viewer 6 6 1 1 5 5 2 3 2 3 4 4 (1) open file : Load the backup data. (2) save : save the playback images as bmp file. (3) playback : playback the backup data. (playback, pause, speed playback, playback by frame) (4) division : 1 division, 4 division, 9 division, 16 division (5) watermark : check if there is any modification of data. (6) status box : display the status of backup viewer.
User Manual z Open file (1) Click ‘Open file’ button from the main screen. (2) Select files to playback. (3) After loading backup file is completed, you can playback backup data and save it as bmp files.
User Manual z Audio playback (1) Load files with audio data. (2) Select and playback the channel, which audio is saved, it playbacks audio data at the same time. z Save (1) Save backup data. (2) Select screen division. (3) Click ‘save’ button. (4) Name the ‘Bmp’ file and save.
User Manual z Watermark (1) Load files to check watermarking (2) Click ‘watermark check’ button. (3) Click playback or speed playback button. (4) It shows the image with error message if there is any modification of data. It shows ‘Ok’ in the status box if there is no modification of data.
User Manual PTZ zPTZ operation press button to display in full screen and you can operate PTZ cameras. PTZ press ‘Enter’ button in PTZ mode, you will see ‘PTZ-ADVANC’ menu. zPTZ general movement (1) moves pan/tilt camera from up/ down and right/ left using arrow keys. (2) enlarge or reduce the screen size by ◀◀ / ▶▶buttons while using zoom camera. (3) can move to other channels by number button on remote controller.
User Manual Audio z Turn on/ off audio. z you can playback the audio in full screen mode. AUDIO Audio On : Turn on audio Mute : Turn off audio AUDIO ON Log search z search every event happened during product operation.
User Manual Remote –controller ID z Remote-controller ID (1) can use to operate several DVRs at one site with one remote-controller. (2) can operate a certain DVR according to the registered ID value. 1 1 2007 9/3 20:00 R:01 A B 1% ① DVR ID z It will turn yellow if remote controller’s ID matches with DVR ID. Then you can operate the DVR. z It will turn red if remote controller’s ID does not match with DVR ID. Then you cannot operate the DVR. z you can set the DVR IDs at System menu.
User Manual Chapter 4 System setup Page: 27 NW-STA-5016/5009/5004 User Manual
User Manual Before setting up system z Starting system menu (1) press ‘Menu’ button. (2) input administrator’s password on the password box.
User Manual z Saving/Canceling menu setup ¾ saving menu setup : select ‘OK’ and press ‘Enter’ button. ¾ canceling menu setup : select ‘Cancel’ and press ‘Enter’ or ‘Menu’ buttons. OK CANCEL z Text input box (1) select letters/symbols using arrow buttons. (2) press ‘Enter’ button to select the letter/symbol. (3) the selected letters/symbols will show on the top text box. TEXT INPUT 0 1 2 3 4 5 6 .
User Manual Setting up screen display zScreen display setup – On Screen Display DISPLAY - OSD STATUS BAR CAMERA TITLE CAMERA BORDER LANGUAGE LEFT MARGIN RIGHT MARGIN TOP MARGIN BOTTOM MARGIN OK CANCEL 9 Status bar – indicate the status bar on the bottom of screen. 9 Camera title – indicate the name of each channel. 9Camera boarder – indicate the boarder-line of each channel. 9Language – select menu language. 9Left margin – adjust the left margin of OSD. 9Right margin – adjust the right margin of OSD.
User Manual zScreen display setup – live sequence scanning (full screen) Setup duration time for live sequence scanning in full screen. NOTE NOTE :: can can input input maximum maximum 99 99 second. second. DISPLAY - LIVE-SEQ(FULL) TIME 02 02 02 02 02 02 02 02 CH 1 2 3 4 5 6 7 8 TIME 02 02 02 02 02 02 02 02 CH 9 10 11 12 13 14 15 16 OK CANCEL zScreen display setup – live sequence scanning (quad screen) Setup duration time for live sequence scanning in quad screen.
User Manual zScreen display setup – spot sequence scanning (quad screen) Setup duration time for spot sequence scanning in quad screen. NOTE NOTE :: can can input input maximum maximum 99 99 second. second.
User Manual zVGA frequency setup the frequency of connected VGA monitor. zAuto setup AUTO DETECT : automatically detects video signals. NOTE NOTE :: ititoperates operates during during system system booting. booting. ItIt is is booted booted as as PAL PALor or NTSC NTSC type type according accordingto to the the video video signal of channel 1. signal of channel 1.
User Manual Camera Setup zCamera setup – general ¾ title – input channel names. ¾ show– show or hide channels. ¾ audio – select connected audio channels. CAMERA - GENERAL CH 1 2 3 4 5 6 7 8 1–8 TITLE CAM01 CAM02 CAM03 CAM04 CAM05 CAM06 CAM07 CAM08 AUDIO CH-01 CH-02 CH-03 CH-04 SHOW ON ON ON ON OFF ON ON OFF OK 9 – 16 CANCEL zCamera setup – PTZ ¾ ID – input camera IDs. ¾ protocol – select the registered protocol. ¾ baud – select the registered baud.
User Manual zCamera setup – preset NOTE NOTE :: system systemwill will record record according accordingto to preset preset positions positions of of camera. camera. check if camera supports preset function before setting check if camera supports preset function before settingup. up. can can setup setup 64 64 preset presetpositions positions for for each each channel. channel.
User Manual zScreen display setup – scan point NOTE NOTE :: you you can can move move camera camera to to follow followthe the path path by bysaved saved preset preset positions positions for for each each channel. channel. You You can can set set 44 scan point list for each channel. scan point list for each channel. ¾ camera – select a camera to set scan point. ¾ list – select a list to save scan point. NOTE NOTE :: you you can can setup setup total total 44lists. lists.
User Manual zCamera setup – adjusting color ¾ camera – select a camera. ¾ bright – adjust color brightness. ¾ contrast – adjust color contrast. ¾ color – adjust camera color ¾ default value – set it as default value. CAMERA - COLOR CAMERA CH1 BRIGHT 0 CONTRAST 0 COLOR 0 DEFAULT OK CANCEL zCamera setup – adjusting position ¾ camera – select a camera ¾ right/left – move the camera to right and left. ¾ default value – set it as default value.
User Manual Record setup zRecord setup – recording quality RECORD - PROPERTY CH 1 2 3 4 5 6 7 8 ALL 1-8 RESOLUTION 360X240 360X240 360X240 360X240 360X240 360X240 360X240 360X240 360X240 9-16 QUALITY NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL FRAMERATE 8 8 8 8 8 8 8 8 NORMAL TOTAL: 120/120 8 OK CANCEL ¾ resolution – set recording resolution for each channel. NTSC PAL 720 x 480 720 x 576 720 x 240 720 x 288 352 x 240 352 x 288 ¾quality – set recording quality for each channel.
User Manual zRecord setup – schedule ¾ system records according to set schedule. ¾ see below to see how to set up schedule. C Continuous recording E Recording when even occurred (Blank) Not recording (1) Select a channel to set up schedule. (2) Select day/time to record and press ‘Enter’ button. (3) it shifts to different type as you press ‘Enter’ button.
User Manual zRecord setup – miscellaneous ¾ overwrite – erase previous video data and record over it when HDD is full. ¾ auto delete – automatically delete data after set date. ¾ continuous record – you cannot stop recording while it is in process as it continuously records. ¾ watermark – activate watermarking function.
User Manual Event setup NOTE NOTE :: you you have have to to set set itit as as ‘Even ‘Even recording’ recording’ at at ‘Schedule ‘Schedule record record setup’ setup’ to to use use this thisfunction. function. zMotion EVENT - MOTION CH 1 2 3 4 5 6 7 8 MOTION-AREA ALL ALL OFF OFF ALL ALL ALL ALL 1-8 SENSITIVITY 5 5 0 0 5 5 5 5 9-16 OK ALARM-OUT NONE NONE NONE NONE NONE NONE NONE NONE CANCEL ¾Motion area – select area to detect motion. (1) all – set the whole screen as motion area.
User Manual zEvent setup - sensor ¾ record – selected channel will be recorded when the sensor is detected. ¾ type – set the type of connected sensor. ¾ alarm out – alarm is activated when the sensor is detected. EVENT - SENSOR SENSOR 1 2 3 4 5 6 7 8 1-8 RECORD OFF OFF OFF OFF OFF OFF OFF OFF TYPE NO NO NO NO NO NO NO NO 9-16 ALARM-OUT NONE NONE NONE NONE NONE NONE NONE NONE OK CANCEL zEvent setup – alarm out ¾ pre-recording time – set recording time before event occurs.
User Manual Storage zStorage – format ¾You must format HDD when you install HDD. (1) select installed HDD and format. (2) system will reboot after formatting is completed. STORAGE – HDD FORMAT HDD1 698GB (ST3750640A) FORMAT HDD2 465GB (ST3500641A) FORMAT HDD3 NONE FORMAT HDD4 NONE FORMAT OK CANCEL zStorage – AUTO-BACKUP ¾ AUTO-BACKUP –idview.com provides external USB TYPE storage. You can backup data using. TYPE : set operation types of AUTO-BACKUP. (1) OFF: turn off AUTO-BACKUP function.
User Manual Network zNetwork – setup ¾ static – input static IP address and gateway, net mask. NETWORK - SETUP TYPE IP ADDRESS STATIC 192.168.000.138 GATEWAY 192.168.000.001 NET MASK 255.255.255.000 MAC ADDRESS 00:0E:00:00:00:00 PPPOR ID PASSWORD **** OK CANCEL ¾ DHCP – system automatically recognizes IP address. NETWORK - SETUP TYPE IP ADDRESS DHCP 192.168.000.138 GATEWAY 192.168.000.001 NET MASK 255.255.255.
User Manual zNetwork - DDNS NOTE NOTE :: system system supports supports free free DDNS DDNS sites sites such such as as dyndns.com, dyndns.com, ipupdater.com. ipupdater.com. ¾ server – select registered server. ¾ server-URL – indicate registered server URL ¾ user ID – input ID registered to server. ¾ password – input password registered to server. ¾ group ID – input group ID registered to server. ¾ status – indicate operation status of DDNS.
User Manual z Access list ¾System can limit remote-PC, accessing network. ¾Able to register Static IP and only remote-PC with registered IP can access system. NETWORK – ACCESS LIST Client 1 000.000.000.000 Client 6 000.000.000.000 Client 2 000.000.000.000 Client 7 000.000.000.000 Client 3 000.000.000.000 Client 8 000.000.000.000 Client 4 000.000.000.000 Client 9 000.000.000.000 Client 5 000.000.000.000 Client 10 000.000.000.
User Manual z Server ¾CC IP – input connection info of CAMS CC. ¾PORT – input connection port of CAMS CC. (default value: 6500) ¾CMM IP – input connection info of CAMS CMM. ¾PORT – input connection port of CAMS CMM. (default value:7600) NETWORK – SERVER CC IP PORT CMM IP PORT 192.168.000.131 6500 192.168.000.
User Manual System zSystem – Configuration info NOTE NOTE :: you you can can save save the the set set values values for formenu menu to to USB USB storage. storage. ¾Load configuration – loads saved configuration information. SYSTEM - CONFIG LOAD CONFIG LOAD CONFIG SAVE CONFIG Device /dev/ sda DEFAULT File List OK config_16_00.cfg OK CANCEL CANCEL ¾Save configuration – save the values set in the current menu.
User Manual zSystem – Time management SYSTEM - TIME CURRENT TIME 2008/03/03 13:39:01 DATE FORMAT TIME FORMAT YY/MM/DD 24HOUR TIME ZONE +09: 00 Seoul DAY LIGHT SAVING OFF START 01/00 00:00 END 01/00 00:00 TIME SYNC SERVER IP OFF TEST OK CHANGE TIME CANCEL ¾Current time – indicates current time of system. ¾Date format – select date format to display. classification display YY/MM/DD 2008/03/03 MM/DD/YY 03/03/2008 DD/MM/YY 03/03/2008 ¾Time format – select time format to display.
User Manual ¾Time synchronization System automatically connects to internet time-server to check current time. ¾Server IP – input time-server IP address. Omit ‘www’. Select ‘OK’ and check if time-server works. example) time.kriss.re.kr www.time.kriss.re.kr correct input wrong input ¾Change time – change system time. NOTE NOTE :: be be cautious cautious when when you you change change system system time. time.
User Manual zSystem – Software ¾Show current software version. ¾Upgrade firmware software. SYSTEM - SOFTWARE ENC. FIRMWARE XXXXXXXX DEC. FIRMWARE XXXXXXXX BOOTLOADER XXXXXXXX KERNEL XXXXXXXX APP. VERSION XXXXXXXX UI XXXXXXXX DB XXXXXXXX RECORDER XXXXXXXX PLAYER XXXXXXXX NETWORK XXXXXXXX UPGRADE OK CANCEL OK CANCEL zSystem – Miscellaneous SYSTEM - MISC SYSTEM – ID KEYBOARD KEY-TONE AUDIO 01 NONE ON MUTE 9 Remote-controller ID – input remote controller ID.
User Manual Chapter 5 Firmware Upgrade Page: 52 NW-STA-5016/5009/5004 User Manual
User Manual NOTE NOTE :: There There are are two two ways ways to to upgrade upgrade firmsare. firmsare. (1) USB upgrade – upgrade (1) USB upgrade – upgrade system system using using USB USB memory memory stick. stick. (2) (2) NETWORK NETWORK upgrade upgrade –– upgrade upgrade system system by by internet internet connection. connection. USB upgrade (1) Copy the provided firmware file to USB memory stick. NOTE NOTE :: firmware firmware file file should should be be saved saved in in rout rout directory.
User Manual Network upgrade z Network upgrade (1) Press ‘Menu’ button and move to the next software. [Menu system software] (2) You will see a new box if you select ‘Upgrade’. (3) Select ‘Network upgrade’. NETWORK UPGRADE SERVER IP dvr-update.com FILE NAME flash-16.tar.gz OK CANCEL (4) Select ‘Server IP’ with firmware file and file name. then select ‘OK’. (5) You can manually input server IP and file name if the system appointed server IP and file name is different.
User Manual Chapter 6 Warranty WARRANTY We warrant that DVR series(Product) will be free from defects in materials and workmanship for a period of one year from the date the customer acquires the Product. If such a defect occurs, return the Product to us and we will, at our opinion, either repair or replace Product. This remedy is your exclusive remedy for breach of this warranty. The proof of purchase is required for the warranty.
User Manual1200 Standalone DVR/GUI USER MANUAL 12000 Ford Rd, Suite 110, Dallas, TX 75234 Tel: 972-247-1203 Fax: 972-247-1291 www.idview.
