Hold H old Time Adjust CAT5 CAMERA SEQUENCER Video Present Camera 1 Camera 2 Camera 3 Camera 4 Loop Out 1 RS-232 PRO Model P-6014 C HANNEL V ISION TM Loop Out 2 Loop Out 3 Loop Out 4 Monitor 1 IR In (Mon 1) Video IR Out (Mon 2) Audio Audio Inputs Power Camera 1 Camera 2 Camera 3 Camera 4 Monitor 2 P-6014 CAT5 Camera Sequencer 6210 Color CAT5 Camera PRO 8
The P-6014 is a 4 input 2 output camera sequencer and switcher for Channel Vision’s 6210 color CAT5 cameras (sold separately). Easily view any of the cameras simply by letting them sequence through the screen automatically or by pressing a button on the optional remote control. The RS-232 interface as well as audio/video loop out connections make it easy to integrate the P-6014 into any security system - from basic to the most complex.
The 6210 Color CAT5 camera with audio mounts in a single gang J-box or low-voltage ring and is designed to be connected directly to the P-6014 camera inputs. The P-6014 provides loop out connections that allow the camera signals to be connected to another device such as a DVR or modulator. BNC Video Output... Connect coax here to use as a conventional camera 6210 Features: RJ-45 Output...
P-6014 Camera Sequencer Basic Application... The primary function of the P-6014 is to sequence through its 4 camera inputs. The Time Adjust control determines the length of time each camera view is shown before switching to the next camera view. Unless the RS-232 or IR remote control features are used, the P-6014 will remain in the Auto Cycle mode. If only three of the four inputs have an active video signal, only the three active camera inputs will be shown when in the Auto Cycle mode.
Using The A0505 Remote Control... P-6014 Camera Sequencer The A0505 is designed to allow you to control the switching functions on your P-6014. The A0505 allows you to choose any of the 4 cameras or select the Auto Cycle mode.
Controlling The P-6014 Through The Monitor 2 Connection... Controlling the P-6014 through the IR Input connection will only affect the Monitor 1 output. To control the Monitor 2 output, IR signals must come through the Monitor 2 output RJ-45 connection via the 3112 as shown below.
RJ-45 Pin Out Diagram... For troubleshooting purposes, it may be helpful to know the wire pin out for the RJ-45 jacks on the P-6014. They are shown below: RJ-45 Jack (TIA 568A) Camera Inputs Monitor 2 Output Pin Signal 8 Gnd 7 Video 6 Gnd 5 N.C. 4 Gnd 3 Audio 2 Gnd 1 +12VDC 8 7 6 5 4 3 2 1 Pin Signal 8 Gnd 7 Video 6 Gnd 5 IR 4 Gnd 3 Audio 2 Gnd 1 +12VDC Controlling The P-6014 Through The RS-232 Port...
RS-232 Control Code... For installations requiring more sophistication the P-6014 supports RS-232 making it extremely compatible with automation systems. Baud Rate: 19200, 8N1 (8Bit Data, No Parity, 1 Stop Bit) Each transmission = 8 ASCII bytes Checksum = The sum of the first 7 bytes inverted and truncated. Note: the checksum for each command is included in the following charts. For troubleshooting purposes, the letter z can be used in place of the checksum character.
Monitor 2 Commands Function ASCII Command Hex Command Monitor 2, Select Camera 1 P64Z2S15 50 36 34 5A 32 53 31 35 Monitor 2, Select Camera 2 P64Z2S24 50 36 34 5A 32 53 32 34 Monitor 2, Select Camera 3 P64Z2S33 50 36 34 5A 32 53 33 33 Monitor 2, Select Camera 4 P64Z2S42 50 36 34 5A 32 53 34 32 Monitor 2, Select Next Cam P64Z2SN[can] 50 36 34 5A 32 53 4E 18 Monitor 2, Auto Cycle P64Z2SR[dc4] 50 36 34 5A 32 53 52 14 Monitor 2, Request Status P64Z2SF[sp] 50 36 34 5A 32 53 46 20 Function
Time Adjust Commands... The following Time Adjust commands alter the amount of time each camera view appears on the screen. Making time adjustments via these RS-232 will override any physical adjustments made using the “Time Adjust” control on the P-6014. You can use either the global commands, which will set the time adjustment on all the cameras, or you can use commands for the specific camera inputs. This allows you to set different viewing times for each of the camera inputs.
Monitor 2 Time Adjust Commands Function ASCII Command Monitor 2, Cam 1, 1 Second P64Z211W P64Z212V Monitor 2, Cam 1, 2 Seconds P64Z213U Monitor 2, Cam 1, 3 Seconds P64Z214T Monitor 2, Cam 1, 4 Seconds P64Z215S Monitor 2, Cam 1, 5 Seconds Monitor 2, Cam 1, 7.
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment.
