/2 2/3 4/5 6/7 9/0 SIK-XXXXA-XX SIK-XXXXC-XX SIK-XXXXP-XX SIK-XXXXI-XX SIK-XXXXSK-XX Elite Telephone Entry Door Intercom
Channel Vision’s SIK-Series door stations can interface with a variety of telephone entry control products to provide communication with the front door. They are available in a variety of configurations including options for an IP or 960H analog camera and compatibility with Panasonic’s popular KSU phone systems. A contact closure is provided for connection to a door strike relay or door strike. 2 2 3 2 2 2 Dimensions: SIK-Rbox (not included) 6.
Understanding the model number: Part numbering: SIK door plates SIK [ [ [ SIK 7 252 A-WN [ Part Number Example: [ U o SIK Elite Series Faceplate 6 7 Analog Camera Megapixel IP Camera 252 282 302 Oil Rubbed Bronze Black Satin Nickel 212 222 232 White** Polished Brass** Antique Brass** A P Compatible with Panasonic KSU’s C P0930 CAT5 Controller I IP Camera with 2 Way Communication Door Station SK WN WB SB SN 8.
Channel Vision Compatible (SIK-xxxxA-xx) The SIK-6xxxA-xx and SIK-7xxxA-xx both interface with the Channel Vision’s telephone entry controllers, P-0920 and P-0921 to provide audio and video communication with the front door. Using a 2-conductor wire, connect the Telephone Entry Controller to the empty screw terminal block on the door station (see diagram).
) Channel Vision CAT5 Intercom Compatible (SIK-xxxxC-xx) ne m). re The diagram below shows how to connect the SIK-xxxxC-xx to Channel Vision’s CAT5 Whole-House Intercom system. When the button is pressed on the SIK-xxxxC-xx the ST-3000 Intercom Stations will generate a door chime. Pressing Answer/End will open communication with the SIK-xxxxC-xx. Model SIK-6xxxC-xx includes an analog 960H color camera and SIK-7xxxC-xx includes an IP camera.
SIK Series Keypad Programming The SIK Series Keypad is an easy to program, easy to use, stand alone, selfcontained entry system with features suitable for basic access control requirements. Providing either a voltage output or dry contact closure, the SIK Series Keypad is designed to control any fail-safe or fail-secure electric locking device. One relay output is available to provide a variety of access control configurations including single door access control, Gate/Garage Door control.
SIK Series Keypad Programming Cont. - K ng ol. as m he on n pad pid ll ps. 3. If you do not know the Master Code, locate the PINK Program wire on the harness. (As an alternative, you can momentarily short the two “PGM” pins on the back of the Keypad. This will take you to step 5) 4. Touch the PINK Program wire to the BLACK wire for one second (The Keypad will beep rapidly 4 times)* 5.
SIK Series Keypad Programming Cont. Programming Door Open Time: The system default is 5 seconds 1. First, determine the length of time you wish to program as the Door Open Time. This is the length of time the door will remain open after a valid Code has been entered. Note: For controlling a garage door or electric gate, you will need to set the door open time to 1 second and remove the “DC +” Jumper on back of keypad. 2. Enter the Master Code (default is “1-3-5-7-9”) followed by the symbol on the keypad.
Time. een door the Hardware Setup Continued Keypad Illumination: Designed for areas will low ambient lighting, the SIK Series Keypad provides nighttime illumination. Keypad illumination is on by default. This option can be turned OFF by cutting the BLUE Illumwire loop on the back of the Keypad. Setting Output Options: The SIK Series Keypad provides options for configuring the relay output as well as the grounding outputs. These options include Voltage vs.
Hardware Setup Remote Bypass: In some cases, it may be necessary to control the door from a remote area such as a security station or reception desk. The SIK Series Keypad provides for a Remote By-Pass (Exit Switch) or Keypad override. This can be accomplished by connecting a normally open switch from the VIOLET Remote Bypass wire to the BLACK wire.
uch a d by the Integrating the ST-C5IDS For systems using the P-0930 Press and hold door station number to activate ST-C5IDS P-0930 ST-3000 Hub . Link In A B C D Room 1 Model P-0930 n be Room 2 Room 4 Room 3 Room 5 PRO CHANNEL VISION Link Out Room 6 Whole-House Intercom TM Page Trigger Page Out IR Power Emitters +15VDC be at ately. ST-C5ID (Sold Separately) (Rear View) OFF 1/2 2/3 4/5 6/7 well n be be at ately. 9/0 - Negative Ground (Green) Strike Power Supply N.O.
Integrating the TE110DS For systems using P-0920 or P-0921 The example shown is a P-0920 and normally open lock type. Ga TE110DS (Sold Separately) Fail-Secure Lock (N.O.) 1/2 Strike Power Supply 2/3 4/5 Common (Green) Connect the green and orange wires from the keypad to the Unlock Door terminals on the P-0920 or P-0921. Triggering the keypad will cause the P-0920 to activate the TE110DS or the P-0921 to activate the Aux terminal or TE110DS and allow the door to open.
Typical Output Wiring Garage Door/Gate Operation (Stand-alone keypad operation): e er ly or or 920 or Fail Safe or Fail Secure lock controller and powered by external power supply (Stand-alone keypad operation): n.
Typical System Diagram Wiring Notes: 1. This system is designed to control a 12 or 24V locking device. To Control any voltage higher than 24 volts, an external relay must be used. 2. The disable latching capability, cut the green wire loop. 3. To disable illumination, cut the blue wire loop. 4. If connecting a door monitor switch, cut the green wire loop. 5. For a garage or gate opener, remove the DC+ jumper and set door open time to one second. 6.
d.
Keypad Configuration - Wiegand 26 Bit PINK - Site Code Program: This Keypad is capable of having the SITE CODE programmed in the field. The PINK wire is used for this procedure. With no voltage applied to the Keypad, connect the PINK wire to the BLACK wire on the wiring harness. Apply the appropriate voltage to the RED and BLACK wires. You will hear 4 rapid audible beeps and both the RED and GREEN LED's will flash at the same rate.
pad, rapid ate. s# will essed ) LACK the he E pad ogic way tion Keypad Configuration - Wiegand 26 Bit Voltage Selection: The factory default setting for the Keypad voltage is 12VDC. Verify that the jumper is removed or placed over only one pin. Do not change the voltage. Keypad Reset: In certain cases you may want to restore system defaults. To perform this procedure: CAUTION: This completely erases the memory & restores factory defaults! 1. Remove power. 2.
Troubleshooting These are a few troubleshooting suggestions to help assist with any problems you may experience. You may contact Channel Vision Technical Support at (714) 424-6500 option two, or email techsupport@channelvision.com Cha wor par Thi doe by C God pur invo will Ma toll ma Thi var war fact Cha sus Cha app any Changed or Deleted a code and the old code still works: The SIK Series Keypad has a total of 6 User Codes. Make sure you’ve changed the desired code.
Two Year Limited Warranty ms Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed.
