WA-320 1-to-1 Wireless Audio Transmitter WA-360 1-to-1 Wireless Audio Receiver 10
The WA-320 1-to-1 Wireless Audio Transmitter and WA-360 1-to-1 Wireless Audio Receiver make it possible to create a distributed audio system without running wires from one room to another. The WA-320 can accept either line level or speaker level audio, making it easy to distribute signals to the rear speakers of a surround sound system. The transmitter and receiver link together on a 1-to-1 basis and can operate over 8 different transmission channels.
Rear Panel Features and Connections: Input Switch... Place in the down position when using speaker-level inputs and up position when using the line-level inputs. J8 & J9 Audio Sense Jumpers... Set to pins 1&2 to enable audio-sensing. Set to pins 2&3 to disable audio-sensing. WA-320 Screw Terminals... Provide power input and audio output connections. Power in Audio Out +V Gnd Gnd Right + Left + J5 & J6 RCA/Screw Terminal Jumpers... When using screw terminals, set to pins 1&2.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions for future reference. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this device near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Linking the WA-360 to the WA-320 The WA-360 and WA-320 operate on a 1-to-1 basis and therefore they must be “Linked” to each other prior to the first use. Once linked they will maintain their paired status even if a power loss occurs. The “RST” button can be used to reset and separate a linked pair. Press and hold the Link button for 3 seconds to begin the linking process. The green PWR/LINK LED will turn orange. The WA-320 can broadcast on 8 different channels.
WA-320 Installation The WA-320 can be installed in the wall using a standard 2-gang junction box or low-voltage mounting ring. For surface mounted or free-standing applications, it can be installed in the back box provided. Follow the simple illustrations below. In-Wall Installation WA-320 Mounting Plate (sold separately) Standard 2-gang ring or j-box (not included) X XXXXXX XXXX 320 WA Align the tabs of the spring plates with the holes in the top and bottom flange of the mounting plate.
WA-360 Installation The WA-360 can be installed in the wall using a standard 1-gang junction box or low-voltage mounting ring. For surface mounted or free-standing applications, it can be installed in the back box provided. Follow the simple illustrations below. In-Wall Installation WA-360 Mounting Plate (sold separately) XXXXXXXXXXX WA360 Standard 1-gang ring or j-box (not included) Align the tabs of the spring plates with the holes in the top and bottom flange of the mounting plate.
Using the WA-320 & WA-360 in a Home Theater The WA-320 can accept the left/right surround speaker outputs from a home theater amplifier and transmit the signal to the WA-360. The WA-360 can then output the signal to a small amplifier like the A0240 which powers the speakers. The volume level of the surround speakers will be raised and lowered by the volume control of the home theater amplifier.
Using the WA-320 & WA-360 for Distributed Audio These wireless audio products make it easy to transmit audio from one room to another. Connect any standard audio component to the input connectors of the WA-320 in Room 1, and use the RCA outputs of the WA-360 to feed an amplifier in Room 2. If a fixed gain amplifier is used (such as the A0240), a volume control like the VC-302 will be needed to adjust the volume level in Room 2.
Troubleshooting: Problem: Hum in System Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away. Cause: The different components in the system are connected to different electrical grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz hum. Solution: Plug products into an electrical circuit with a common ground. If it can be done safely, consider lifting the ground with a ground lifting plug.
Specifications: (typical at 25º C) General: Storage Temperature: Operating temperature: -40 to +85º C 0 to +55º C Transmit and Receive: Input Voltage: THD+N: S/N Ratio: Audio Latency: Operating Frequency: Data Rate: Audio Sampling Rate: Channels: 6-30 VDC 0.7% Max 80 dB 3.8 ms 2400 MHz 1.152 Mbps 48 kHz 8 (User Selectable) Transmit: Transmission Power: Modulation Type: Channel Spacing: Max. Audio Input: Input Impedance: Max. Speaker Level In: 8.5 dB (9.5dB Max) GFSK 9 MHz 2.
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment.
