User Manual

Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye or other
injury. For safe use of this product you must read and follow all instructions. Do not leave a pressurized sprayer in the hot
sun. Heat can cause pressure build-up. Do not store or leave solution in tank after use. Always wear goggles, gloves, long
sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove pump if there is pressure
in sprayer. Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than the original
pump. Do not attempt to modify or repair this product except with original manufacturer’s parts. Never spray ammable
materials or heat, pressure, or gas producing chemicals. Always read and follow manufacturer’s instructions before
use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING!
Sk-1113-1
Parts, Piezas, Pièces
6-2001
Hose Kit: 2 nuts,2 barbs, hose
Juego de manguera: 2 tuercas, 2 lengüetas, manguera
Nécessaire de tuyau: Deux écrous, deux ardillons, tuyau
6-2000
Shut-o Handle
Mango de cierre
Poignée du robinet
301120-4
Brass FanNozzle
Tobera en latón
Buse-éventail en laiton
Printed in USA
1. Hose to Tank
2. Nozzle / Extension Wand
Attach nozzle to shut-o handle or extension wand.
3. Filter
e lter helps prevent clogging while spraying. It is located on the end of the outlet tube inside your
sprayer tank.To clean lter, remove the discharge assembly from the tank (Fig.1A). Make sure the
lter is positioned at the bottom of the tank as pictured
Note: Filters are not supplied with deck sprayers.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose before using. Replace
with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of deterioration of
body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive bursting under pressure. If any
of these signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-o away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling, Pressurizing and
Spraying Instructions.
6. Pre-Use Check
7. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
8. Pressurizing and Spraying
Do: Turn handle clockwise to tight-
en. Push handle down, turn 1/4
turn counterclockwise to release.
Do: Pump until you
feel resistance.
Do: Push handle, down, turn 1/4 turn clockwise to
lock. Begin spraying. Re-pump sprayer as required
to maintain spray force.
10. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling, Pressurizing and Spraying Instructions,
except pump unit only 8-10 strokes.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
6-5385
Spray Shield
Pantalla de pulverización
Bouclier de pulvérisation
6-5364
Measure Cup
Taza para medir
Tasse à mesurer
3-7749-18
Extension wand, Vara de extensión, Lance de rallonge
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known to the State of California
to cause birth defects and other reproductive harm. Wash hands after handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
010879-1 (A) R0110
8A
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Discharge/ Assembly
• Insure the tool holder is assembled to the tank adapter before mounting the discharge assembly (Fig.1A). e Tool
Holder snaps into the groove of the tank adapter. Figure 1D shows how the shield and cup are mounted.
• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1A).
• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter and outlet tube adapter.
• Firmly tighten the retaining nut to the tank adapter (Fig. 1C).
WARNING!
To prevent hose from blowing o, hose must cover both barbs on the outlet tube adapter and
touch ange (Fig. 1B) before hose nut is securely tightened (Fig. 1C).
301272-4
Adjustable Brass Nozzle
Boquilla de latòn regulable
Buse en laiton réglable
6-4566
4 Position Nozzle
Boquilla de 4 posiciones
Buse à 4 positions
3-2102
Poly Fan Nozzle Kit
Juego de boquilla en abanico polietileno.
Nécessaire de buse éventail en polyéthylène
1A
301481
Pump Assembly
Ensamblaje De La Bomba
Assemblage De La Pompe
6-5386
Repair Kit
Juego de reparación
Kit de réparation
010842
Tool Holder
Soporte para la herramienta
Porte-outils
1C
Retaining Nut -
Securely tightened.
Tool
Holder
Measuring
Cup
Spray
Shield
1D
1B
No
Gap
Tank
Adapter
Outlet
Tube
Adapter
Tool
Holder
Outlet
Tube
Discharge
Assembly
2A
Nozzle
Shut-o
2B
Extension Wand
4. Fatigue-free Spraying
Filter
3A
8B
8C
For constant spraying, push down on shut-o handle and move gray locking mechanism away
from you. To release, squeeze handle and move the gray locking mechanism back toward you.
Note: Fatigue-free spraying lock is not supplied with all sprayers.
5. Shield Attachment to Wand
Snap shield onto
wand as shown.
Using the spray shield will
help protect your plants from
over spray.
5A 5B
4A
2D2C
Red,
Fine spray for
ner washes
Blue,
Medium spray for
sealers
Yellow,
Course spray for semi-
transparent stains
Attach cap to shut-o handle or extension wand (Fig. 2D-2E).
Deck Sprayers Only ( Fig. 2C-2E)
Insert nozzle into cap (2C).
2E
Pull handle straight up.
Insert notches from
underside of handle
into plunger grooves
and turn counter-
clockwise.
Remove plunger and diaphragm.
Clean plunger, diaphragm
and body. Flip diaphragm and
replace.
Tighten plunger clockwise until
ush to top of shut-o body.
Do not over-tighten or unit
may not spray. Slide forks un-
der plunger, push handle down
until it snaps into place.
11. Troubleshooting - Tank pressurizes but does not spray.
11A 11B 11C
Handle
Plunger
Body
Diaphragm
11D
Plunger ush
with body
WARNING: Release pressure in tank before troubleshooting.
Clean Nozzle Assembly (Fig. 11E) -Remove nozzle cap. Clean and re-assemble.
Clean shut-off (Fig. 11A- 11D)
11E
Nozzle Cap
9. To Release Pressure
1) Your sprayer is equipped with a pressure release button. To release
pressure press red button until air is completely exhausted.
2) Do: Point air ow away from you and others until air has escaped.
9A