Use and Care Manual

ManualsBrandsChar-Griller ManualsGas GrillsGrillin Pro 3-Burner Propane Gas Grill in Black

OM3072 E.1

™ & © Char-Griller / A&J Mfg. 24

Connecting Gas Cylinder:

The propane gas supply cylinder to be used must be constructed and marked in

accordance with the Specifications for propane gas Cylinders of the U.S. Depart-

ment of Transportation (DOT), or the National Standard of Canada, CAN/CSA

B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and

Commission, as applicable. Only cylinders with a listed overfill prevention device

(OPD) and marked “propane” may be used. Cylinders with an OPD will have valve

handles with three “lobes” (prongs). Only use 20-pound cylinders equipped with a

Type 1 cylinder connection device for outdoor cooking appliances. The cylinder

must include a collar to protect the cylinder valve. The gas cylinder should not be

dropped or handled roughly! If the appliance is not in use, the gas cylinder must

be disconnected. Storage of an appliance indoors is permissible ONLY if the cylin-

der is disconnected and removed from the appliance. Cylinders must be stored

outdoors out of the reach of children and must not be stored in a building, garage

or any other enclosed area. Your cylinder must never be stored where tempera-

tures can reach over 125 F. Before connection, be sure that there is no debris

caught in the head of the gas cylinder, head of the regulator valve or in the head of

the burner and burner ports. Connect regulator valve and hand-tighten firmly. Dis-

connect the propane cylinder from the regulator valve when the grill is not in use.

DO NOT obstruct the flow of combustion air and ventilation air to the grill. The pro-

pane cylinder must be arranged for vapor withdrawal and equipped with a listed

overfilling prevention device. For proper vapor withdrawal, the cylinder should be

used in the proper upright position (refer to illustration under step 22 of page 17).

DANGER:

Never store a spare propane cylinder near this grill.

A fire causing death or serious injury may occur if the above is not followed

exactly.

Step 12: Install the Burners into the Grill Body by inserting the IGNITER WIRES and

Burners through the open holes at the front of the Grill Body from inside of the Grill

Body, see figure 12A. (NOTE: IGNITER MUST BE ON BOTTOM SIDE OF BURNER). The

BURNER with the longer wire goes on the right side of the GRILL BODY. Making sure

that the Valve goes inside each burner, see figure 12B. Then secure the Burners to

the Grill Body with the screws provided, see figure 12C.

Figure 12A

Figure 12B

Figure 12C

Valve

Burner

Screw

Burner

Igniter with Wire

Summary of content (12 pages)

PAGE 1
Connecting Gas Cylinder: The propane gas supply cylinder to be used must be constructed and marked in accordance with the Specifications for propane gas Cylinders of the U.S. Department of Transportation (DOT), or the National Standard of Canada, CAN/CSA B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable. Only cylinders with a listed overfill prevention device (OPD) and marked “propane” may be used.
PAGE 2
Step 10 Secure the Hose Guide Bracket to the side of the Grill. First unscrew the lower bolt that secure the front side of the leg brace. Then place the Hose Guide over the Leg Brace and re-screw the bolt. Cleaning and Care Caution: All cleaning and maintenance should be done when grill is cool and with the gas supply turned off at the propane cylinder. DO NOT clean any grill part in a self cleaning oven. The extreme heat will damage the finish. Cleaning Burning-off the grill after every use (approx.
PAGE 3
Step 9 Install Knobs onto valve’s stems on Side Burner Body/Control Panel Assembly. Then install Side Burner Body/Control Panel Assembly onto the Grill Body. Lay down the Side Burner Body Assembly that connect with the Control Panel on the floor and attach the Control Pane to the front of the Grill Body with four 1/2” Hex Bolts and four Lock Washers (two Hex Bolts and two Lock Washers on each side). Then attach the Side Burner Body Assembly on the side of the Grill Body with four 1/2” Hex Bolts.
PAGE 4
Step 8 Install the Catch Pan onto the bottom of the Grill Body by sliding the Catch Pan underneath the Grill Body bottom. Making sure that the Brackets on the Catch Pan rest on top of Slider Brackets. Slid the Catch Pan all the way till you can hang the Catch Pan side bracket onto the Stopper Bracket. Stand in front of the grill to operate the controls. Catch Pan Side Bracket Note: Before starting the grill, check for leaks.
PAGE 5
Lighting Your Grill Danger: Failure to open hood while igniting the grill or not waiting 5 minutes to allow the gas to clear if the grill does not light, may result in an explosive flare-up which can cause serious bodily injury or death. Before cooking on this grill for the first time, operate the grill for about 15 minutes with the lid closed and the gas turned on “high”. This will “heat clean” the internal parts and dissipate odor from the manufacturing processes and painted finish.
PAGE 6
Step 4 Stand the Cart up right. Place Front Panel between Short and Long Legs and secure it with four Lock Washers and four 1/2” Hex Bolts. Front Panel Side Burner 1. Open lid during lighting. Lid must be open when burner is on. 2. Burner valves must be in the “off” position. Hex Bolts 3. Open cylinder valve. 4. Push in side burner valve knob fully and rotate slowly about ¼ turn counterclockwise until a click is heard. If the burner does not light, immediately turn the valve knob to OFF.
PAGE 7
Lighting Burner With a Match: 1. Place a match in the end of the match holder that is installed on the side of Grill Housing. Once lit, immediately place the flame through the cooking grates as shown near the burner ports. Step 2 Lay the cart assembly from previous step on one side then place the Bottom Shelf between the four legs then secure it with four Lock Washers and four 1/2” Hex Bolts. The Bottom Shelf with the Tank Hole should be on the Short Legs side opposite the Long Legs.
PAGE 8
Assembly Instructions Step 1: Insert the Long Legs and Short Legs into the opening ends of the Leg Cross Bars. Then place the Leg Braces over the Legs and Leg Cross Bars and secure them with Lock Washers and two 1/2” Hex Bolts per leg. (NOTE: The orientation of the Leg Cross Bar is very important for later steps. The two holes on each Leg Cross Bar must be facing toward the center of the assembly.
PAGE 9
Assembly: Requires 2 people. Get another person to help. Tools Needed: Pliers, Phillips Head Screwdriver and a 7/16” Nut Driver. NOTE: Do Not tighten any bolts unless instructed to do so. Tightening too soon may prohibit parts from fitting together. All Hex Nuts should be on the inside of the grill unless stated otherwise. Unpack all contents in a well cleared and padded area. STOP! Do Not Return to Store. If you are missing parts or need assistance please email us at info@chargriller.
PAGE 10
Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 DescripƟon GAS HOOD ASSEMBLY MANIFOLD/VALVES ASEEMBLY CONTROL PANEL (UFC) KNOB IGNITOR CATCH PAN, SMALL GREASE TRAY BOTTOM HALF SIDE SHELF UTENSIL HOOK LEG CROSS BAR LEG BRACE LONG LEG LEG CAP FRONT PANEL BOTTOM SHELF TANK BLOCK BAR AXLE ROD SHORT LEG WHEEL HUB CAP HOSE/VALVE/REGULATOR ASSEMBLY KNOB BEZEL VALVE, INTEGRATED, SB SIDEBURNER SHELF BODY SIDE BURNER IGNITOR SIDE BU
PAGE 11
GRILLING RECIPES DIRECT METHOD STEAK (& ALL MEATS): Cook food directly above coals/heat. Generally speaking, to grill meats, raise fire grate to high position (hot) and sear for one minute on each side with the lid open to seal in flavor and juices. Then lower fire grate to medium position with lid closed and cook to desire doneness. Control heat with dual dampers and adjustable fire grate.
PAGE 12
10. Do not touch metal parts of grill until it has completely cooled (about 45 minutes) to avoid burns, unless you are wearing protective gear (BBQ mittens, pot holders, etc.) 11. Do not alter this grill in any manner 12. Clean and inspect the hose before each use. If there is evidence of abrasion, wear, cuts, or leaks, the hose must be replaced prior to operating the appliance. The replacement hose assembly will be that which is specified by the manufacturer. 13.