Technical Specifications

20
Plastics Technical Manual
GENERAL INFORMATION
SUBMITTAL FOR CHARLOTTE PIPE
®
PVC SDR 35 GRAVITY SEWER PIPE
Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.
FO-SUB-PVC-SDR-35 (5-2-18)
Date: ________________
Job Name: ______________________________ Location: _______________________________
Engineer: _______________________________ Contractor: ______________________________
Scope:
This specication covers PVC Standard Dimensional Ratio (SDR) 35 PSM pipe for gravity sewer and surface water
applications with a pipe stiffness of 46. This systems is intended for gravity applications where the operating temperature
will not exceed 140°F.
Specication:
Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class of 12364 as identied
in ASTM D 1784. The requirement of this specication are intended to provide pipe suitable for non-pressure drainage and
surface water.
PVC SDR 35 PSM pipe shall conform to ASTM D 3034 for gasket or solvent-weld pipe with a minimum pipe stiffness of 46.
Gaskets shall conform to ASTM F 477. The term “PSM” is not an acronym, but rather an arbitrary designation for a product
having certain dimensions.
Installation:
Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall conform to
all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance with ASTM D 2321
and ASTM F 1668. Solvent cement joints shall be made in a two-step process with primer conforming to ASTM F 656 and
solvent cement conforming to ASTM D 2564. The system shall be protected from chemical agents, re-stopping materials,
thread sealant, plasticized-vinyl products or other aggressive chemical agents not compatible with PVC compounds. The
system shall be hydrostatically tested after installation WARNING! Never test with or transport/store compressed air or gas
in PVC pipe or ttings. Doing so can result in explosive failures and cause severe injury or death.
Referenced Standards:
ASTM D 1784 Rigid Vinyl Compounds
ASTM D 3034 PVC Gravity Sewer Pipe (SDR) 35 PS 46
ASTM D 2564 Solvent Cements for PVC Pipe and Fittings
ASTM D 2321 Underground Installation of Thermoplastic Pipe (non-pressure applications)
ASTM F 477 Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM F 656 Primers for PVC Pipe and Fittings
ASTM F 1668 Procedures for Buried Plastic Pipe
Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • [phone] • www.charlottepipe.com
PVC SDR 35 PSM Pipe
ASTM D 3034 & ASTM F 477
SDR-35 SOLVENT WELD - PS 46
S/M 6004 4”x10’ 04008 600’ 10’-0” 108.3 4.215 .120
S/M 6004 4”x20’ 04009 1200’ 20’-0” 108.3 4.215 .120
S/M 6006 6”x10’ 04013 280’ 10’-0” 241.7 6.275 .180
S/M 6006 6”x20’ 04014 560’ 20’-0” 241.7 6.275 .180
PART NO. NOM. SIZE UPC # QTY. PER LAYING WT. PER AVG. OD MIN. WALL
611942- SKID LENGTH 100 FT. (LBS.) (IN.) (IN.)
SDR-35 GASKETED - PS 46
PART NO. NOM. SIZE UPC # QTY. PER LAYING WT. PER AVG. OD MIN. WALL
611942- SKID LENGTH 100 FT. (LBS.) (IN.) (IN.)
S/M 6004G 4”x14’ 11920 840’ 14’-0” 110.4 4.215 .120
S/M 6004G 4”x20’ 04012 1200’ 20’-0” 109.7 4.215 .120
S/M 6006G 6”x14’ 11921 392’ 14’-0” 249.6 6.275 .180
S/M 6006G 6”x20’ 04016 560’ 20’-0” 247.0 6.275 .180
S/M 6008G 8”x14’ 11922 140’ 14’-0” 451.0 8.400 .240
Weight is approximate and is for shipping purposes only.
PVC Sewer Pipe
PVC SDR 35 PSM Pipe
ASTM D 3034 & ASTM F 477
Meets All Requirements of ASTM D 3034.
SDR 35 Gaskets meet or exceed ASTM F 477. Gasketed joints meet ASTM D 3212.