Technical Specifications

10
Plastics Technical Manual
GENERAL INFORMATION
SUBMITTAL FOR CHARLOTTE PIPE
®
ABS CELLULAR (FOAM CORE) PIPE AND ABS DWV FITTING SYSTEM
Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.
FO-SUB-ABS (4-10-17)
Date: ________________
Job Name: ______________________________ Location: _______________________________
Engineer: _______________________________ Contractor: ______________________________
Scope:
This specication covers ABS cellular core (foam core) pipe and ABS DWV ttings used in sanitary drain, waste and
vent (DWV), sewer, and storm drainage applications. This system is intended for use in non-pressure applications
where the operating temperature will not exceed 140° F.
Specication:
Pipe shall be manufactured from virgin rigid ABS (acrylonitrile-butadiene-styrene) compounds with a cell class of
42222 as identied in ASTM D 3965. Fittings shall be manufactured from virgin rigid ABS compounds with a cell class
of 32222 as identied in ASTM D 3965.
ABS cellular core pipe shall be Iron Pipe Size (IPS) conforming to ASTM F 628. Injection molded ABS DWV ttings
shall conform to ASTM D 2661. All systems shall utilize a separate waste and vent system. All pipe and ttings shall
be manufactured in the United States. Pipe and ttings shall conform to NSF International Standard 14.
Installation:
Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall
conform to all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance
with ASTM D 2321 and ASTM F 1668. Solvent cement joints shall be made with a solvent cement conforming
to ASTM D 2235. The system shall be protected from chemical agents, re-stopping materials, thread sealant,
plasticized-vinyl products or other aggressive chemical agents not compatible with
ABS compounds. The system shall
be hydrostatically tested after installation. WARNING!
Never test with or transport/store compressed air or gas in ABS
pipe or ttings. Doing so can result in explosive failures and cause severe injury or death.
Referenced Standards:
ASTM D 3965: Rigid ABS Compounds
ASTM F 628: Co-extruded ABS Pipe with Cellular Core
ASTM D 2661: ABS Drain, Waste and Vent Fittings
ASTM D 2235: Solvent Cements for ABS Pipe and Fittings
ASTM D 2321: Underground Installation of Thermoplastic
Pipe (non-pressure applications)
ASTM F 1668: Procedures for Buried Plastic Pipe
NSF Standard 14: Plastic Piping Components and
Related Materials
Not all tting patterns shown
Combination Wye
& Eighth Bend
Closet FlangeP-Trap
Double
Sanitary Tee
Eighth Bend
Quarter Bend
Coupling
Cleanout Tee
w/Plug
ABS Foam Core Pipe
Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • [phone] • www.charlottepipe.com
ABS Schedule 40 DWV Pipe
(For Non-Pressure Applications)
ABS 3112 1
1
⁄ 2 ” x 10’ 03132 2590’ 1.900 0.145 27.1
ABS 3112 1
1
⁄ 2 ” x 20’ 03133 5180’ 1.900 0.145 27.1
ABS 3200 2” x 10’ 03134 1670’ 2.375 0.154 37.7
ABS 3200 2” x 20’ 03135 3340’ 2.375 0.154 37.7
ABS 3300 3” x 10’ 03136 750’ 3.500 0.216 74.5
ABS 3300 3” x 20’ 03137 1500’ 3.500 0.216 74.5
ABS 3400 4” x 10’ 03138 480’ 4.500 0.237 107.1
ABS 3400 4” x 20’ 03139 960’ 4.500 0.237 107.1
ABS 3600 6” x 20’ 03141 400’ 6.625 0.280 187.8
ABS SCHEDULE 40 FOAM CORE (BLACK) PLAIN END ASTM F 628
MIN. WT. PER
PART NO. NOM. SIZE UPC # QTY. PER AVG. OD WALL 100 FT.
611942- SKID (IN.) (IN.) (LBS.)