Technical Specifications

13
GENERAL INFORMATION
SUBMITTAL FOR CHARLOTTE PIPE
®
PVC CELLULAR (FOAM CORE) PIPE AND PVC DWV FITTING SYSTEM
Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.
FO-SUB-PVC-FC (7-5-18)
Date: ________________
Job Name: ______________________________ Location: _______________________________
Engineer: _______________________________ Contractor: ______________________________
Scope:
This specication covers PVC cellular (foam core) pipe and PVC DWV ttings used in sanitary drain, waste and vent
(DWV), sewer, and storm drainage applications. This system is intended for use in non-pressure applications where
the operating temperature will not exceed 140° F.
Specication:
Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class of 11432 as
identied in ASTM D 4396. Fittings shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds
with a cell class of 12454 as identied in ASTM D 1784.
PVC cellular core pipe shall be Iron Pipe Size (IPS) conforming to ASTM F 891. Injection molded PVC DWV ttings
shall conform to ASTM D 2665. Farbricated PVC DWV ttings shall conform to ASTM F 1866. All systems shall utilize
a separate waste and vent system. All pipe and ttings shall be manufactured in the United States. Pipe and ttings
shall conform to NSF International Standard 14.
Installation:
Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall
conform to all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance
with ASTM D 2321 and ASTM F 1668. Solvent cement joints shall be made in a two-step process with primer
conforming to ASTM F 656 and solvent cement conforming to ASTM D 2564. The system shall be protected from
chemical agents, re-stopping materials, thread sealant, plasticized-vinyl products or other aggressive chemical
agents not compatible with PVC compounds. The system shall be hydrostatically tested after installation.
WARNING! Never test with or transport/store compressed air or gas in PVC pipe or ttings. Doing so can result in
explosive failures and cause severe injury or death.
Referenced Standards:
ASTM D 4396: Compounds for Cellular Core
ASTM F 891: Co-extruded PVC Pipe with Cellular Core
ASTM D 2665: PVC Drain, Waste and Vent Fittings
ASTM D 2564: Solvent Cements for PVC Pipe and Fittings
ASTM D 2321: Underground Installation of Thermoplastic
Pipe (non-pressure applications)
ASTM F 1668: Procedures for Buried Plastic Pipe
ASTM F 1866: Fabricated PVC DWV Fittings
NSF Standard 14: Plastic Piping Components and
Related Materials
Not all tting patterns shown
Combination Wye
& Eighth Bend
Closet FlangeP-Trap
Double
Sanitary Tee
Eighth Bend
Quarter Bend
Coupling
Cleanout Tee
w/Plug
PVC Foam Core Pipe
Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • [phone] • www.charlottepipe.com
PVC Schedule 40 DWV Pipe
(For Non-Pressure Applications)
PVC SCHEDULE 40 FOAM CORE (WHITE) PLAIN END ASTM F 891
PVC 4112 1
1
⁄ 2 ” x 10’ 04178 1650’ 1.900 0.145 32.3
PVC 4112 1
1
⁄ 2 ” x 20’ 04177 3300’ 1.900 0.145 32.3
PVC 4200 2” x 10’ 04174 1110’ 2.375 0.154 43.9
PVC 4200 2” x 20’ 04173 2220’ 2.375 0.154 43.9
PVC 4300 3” x 10’ 03934 1040’ 3.500 0.216 89.7
PVC 4300 3” x 20’ 03935 920’ 3.500 0.216 89.7
PVC 4400 4” x 10’ 03936 600’ 4.500 0.237 123.8
PVC 4400 4” x 20’ 03937 1200’ 4.500 0.237 123.8
PVC 4600 6” x 10’ 03938 330’ 6.625 0.280 235.0
PVC 4600 6” x 20’ 03939 660’ 6.625 0.280 235.0
PVC 4800 8” x 20’ 03941 360’ 8.625 0.322 371.0
PVC 4910 10” x 20’ 03942 220’ 10.750 0.365 566.3
PVC 4912 12” x 20’ 03943 120’ 12.750 0.406 700.0
MIN. WT. PER
PART NO. NOM. SIZE UPC # QTY. PER AVG. OD WALL 100 FT.
611942- SKID (IN.) (IN.) (LBS.)