Warranty Guide

12
Plastics Technical Manual
GENERAL INFORMATION
SUBMITTAL FOR CHARLOTTE PIPE
®
PVC SCHEDULE 40 SOLID WALL PIPE AND PVC DWV FITTING SYSTEM
Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.
FO-SUB-PVC-DWV (6-25-18)
Date: ________________
Job Name: ______________________________ Location: _______________________________
Engineer: _______________________________ Contractor: ______________________________
Scope:
This specication covers PVC Schedule 40 solid wall pipe and PVC DWV ttings used in sanitary drain, waste and
vent (DWV), sewer and storm drainage applications. This system is intended for use in non-pressure applications
where the operating temperature will not exceed 140° F.
Specication:
Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class of 12454 as
identied in ASTM D 1784. PVC Schedule 40 pipe shall be Iron Pipe Size (IPS) conforming to ASTM D 1785 and
ASTM D 2665. Injection molded PVC DWV ttings shall conform to ASTM D 2665. Fabricated PVC DWV ttings shall
conform to ASTM F 1866. All pipe and ttings shall be manufactured in the United States. All systems shall utilize a
separate waste and vent system. Pipe and ttings shall conform to NSF International Standard 14.
Installation:
Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall
conform to all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance
with ASTM D 2321 and ASTM F 1668. Solvent cement joints shall be made in a two-step process with primer
conforming to ASTM F 656 and solvent cement conforming to ASTM D 2564. The system shall be protected from
chemical agents, re-stopping materials, thread sealant, plasticized-vinyl products or other aggressive chemical
agents not compatible with PVC compounds. The system shall be hydrostatically tested after installation.
WARNING! Never test with or transport/store compressed air or gas in PVC pipe or ttings. Doing so can result in
explosive failures and cause severe injury or death.
Referenced Standards:
ASTM D 1784: Rigid Vinyl Compounds
ASTM D 1785: PVC Plastic Pipe, Schedule 40
ASTM D 2665: PVC Drain, Waste and Vent Pipe and Fittings
ASTM D 2564: Solvent Cements for PVC Pipe and Fittings
ASTM D 2321: Underground Installation of Thermoplastic
Pipe (non-pressure applications)
ASTM F 656: Primers for PVC Pipe and Fittings
ASTM F 1668: Procedures for Buried Plastic Pipe
ASTM F 1866: Fabricated PVC DWV Fittings
NSF Standard 14: Plastic Piping Components and
Related Materials
Not all tting patterns shown
Combination Wye
& Eighth Bend
Closet FlangeP-Trap
Double
Sanitary Tee
Eighth Bend
Quarter Bend
Coupling
Cleanout Tee
w/Plug
PVC Schedule 40 DWV Pipe
Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • [phone] • www.charlottepipe.com
PVC Schedule 40 DWV Pipe
PVC 7100* 1
1
⁄ 4 ”x10’ 03945 2120’ 1.660 .140 42.4
PVC 7100* 1
1
⁄ 4 ”x20’ 03946 4240’ 1.660 .140 42.4
PVC 7112* 1
1
⁄ 2 ”x10’ 03947 1650’ 1.900 .145 51.8
PVC 7112* 1
1
⁄ 2 ”x20’ 03948 3300’ 1.900 .145 51.8
PVC 7200* 2”x10’ 03949 1110’ 2.375 .154 69.5
PVC 7200* 2”x20’ 03950 2220’ 2.375 .154 69.5
PVC 7300* 3”x10’ 03951 1040’ 3.500 .216 144.2
PVC 7300* 3”x20’ 03952 920’ 3.500 .216 144.2
PVC 7400
†
4”x10’ 03953 600’ 4.500 .237 205.5
PVC 7400
†
4”x20’ 03954 1200’ 4.500 .237 205.5
PVC 7500
†
5”x20’ 04837 760’ 5.563 .258 272.5
PVC 7600
†
6”x10’ 03955 330’ 6.625 .280 361.2
PVC 7600
†
6”x20’ 03956 660’ 6.625 .280 361.2
PVC 7800
†
8”x10’ 13087 180’ 8.625 .322 543.6
PVC 7800
†
8”x20’ 03958 360’ 8.625 .322 543.6
PVC 7910
†
10”x20’ 03959 220’ 10.750 .365 770.7
PVC 7912
†
12”x20’ 03961 120’ 12.750 .406 1019.0
PVC 7914
†
14”x20’ 04862 60’ 14.000 .437 1205.0
PVC 7916
†
16”x20’ 04918 60’ 16.000 .500 1575.7
PVC SCHEDULE 40 (WHITE) PLAIN END PVC 1120 ASTM D 2665
PVC SCHEDULE 40 (WHITE) PLAIN END PVC 1120 ASTM D 2665
PART NO. NOM. SIZE UPC # QTY. PER AVG. OD MIN. WALL WT. PER 100 FT.
611942- SKID (IN.) (IN.) (LBS.)
* Dual Marked ASTM D 1785 & ASTM D 2665.
†
Triple Marked ASTM D 1785 & ASTM D 2665 & ASTM F 480.