Warranty Guide

ManualsBrandsCharlotte Pipe ManualsFittings4 in. x 3 in. Connectite Closet Flange with Stop

PO Box 35430 Charlotte, NC 28235 USA 704/348-6450 800/572-4199 FAX 800/553-1605

Literature-By-Fax 800/745-9382 www.charlottepipe.com

Charlotte Pipe and Foundry Company

(Charlotte Pipe

)

Products are warranted to be free from manufacturing

defects and to conform to currently applicable standards for a

period of ten (10) years from date of delivery. Buyer’s remedy

for breach of this warranty is limited to replacement of, or

credit for, the defective product. This warranty excludes any

expense for removal or reinstallation of any defective product

and any other incidental, consequential, or punitive damages.

This limited warranty is the only warranty made by seller

and is expressly in lieu of all other warranties, express

and implied, including any warranties of merchantability

and ﬁtness for a particular purpose. No statement, conduct

or description by Charlotte Pipe or its representative, in

addition to or beyond this Limited Warranty, shall constitute

a warranty. This Limited Warranty may only be modiﬁed in

writing signed by an ofﬁcer of Charlotte Pipe.

This Limited Warranty will not apply if:

1) The Products are used for purposes other than their

intended purpose as deﬁned by local plumbing and

building codes, and the applicable standard.

2) The Products are not installed in good and workmanlike

manner consistent with normal industry standards;

installed in compliance with the latest instructions

published by Charlotte Pipe and good plumbing practices;

and installed in conformance with all applicable

plumbing, ﬁre and building code requirements.

3) This limited warranty does not apply when the products

of Charlotte Pipe are used with the products of other

manufacturers that do not meet the ASTM standard or

that are not marked in a manner to indicate the entity

that manufactured them.

4) The Products fail due to defects or deﬁciencies in design,

engineering, or installation of the piping system of which

they are a part.

5) The Products have been the subject of modiﬁcation;

misuse; misapplication; improper maintenance or repair;

damage caused by the fault or negligence of anyone other

than Charlotte Pipe; or any other act or event beyond

the control of Charlotte Pipe.

6) The Products fail due to the freezing of water in the

Products.

7) The Products fail due to contact with chemical agents,

ﬁre stopping materials, thread sealant, plasticized vinyl

ConnecTite

Limited Warranty

ConnecTite, Charlotte and Charlotte Pipe are registered trademarks of Charlotte Pipe and Foundry Company.

WA-CT (1-15-16)

Testing with or use of compressed air or gas in PVC / ABS

/ CPVC pipe or fittings can result in explosive failures and

cause severe injury or death.

• NEVER test with or transport/store

compressed air or gas in PVC / ABS / CPVC

pipe or fittings.

• NEVER test PVC / ABS / CPVC pipe or

fittings with compressed air or gas, or air

over water boosters.

• ONLY use PVC / ABS / CPVC pipe or

fittings for water or approved chemicals.

• Refer to warnings on PPFA’s website and

ASTM D 1785.

products, or other aggressive chemical agents that are

not compatible.

8) Pipe outlets, sound attenuation systems or other devices

are permanently attached to the surface of Charlotte

PVC, ABS or CPVC products with solvent cement or

adhesive glue.

Charlotte Pipe products are manufactured to the applicable

standard. Charlotte Pipe and Foundry cannot accept

responsibility for the performance, dimensional accuracy,

or compatibility of pipe, ﬁttings, gaskets, or couplings not

manufactured or sold by Charlotte Pipe and Foundry.

Any Charlotte Pipe products alleged to be defective must be

made available to Charlotte Pipe at the following address for

veriﬁcation, inspection and determination of cause:

Charlotte Pipe and Foundry Company

Attention: Technical Services

2109 Randolph Road

Charlotte, North Carolina 28207

Purchaser must obtain a return materials authorization

and instructions for return shipment to Charlotte Pipe of any

product claimed defective or shipped in error. Please refer

to the Return Material Policy on the back of this page for

speciﬁc instructions on returning materials to Charlotte Pipe.

Any Charlotte Pipe product proved to be defective in

manufacture will be replaced F.O.B. point of original delivery,

or credit will be issued, at the discretion of Charlotte Pipe.

1/15/16

Summary of content (2 pages)

PAGE 1
ConnecTite® Limited Warranty Charlotte Pipe and Foundry Company® (Charlotte Pipe®) Products are warranted to be free from manufacturing defects and to conform to currently applicable standards for a period of ten (10) years from date of delivery. Buyer’s remedy for breach of this warranty is limited to replacement of, or credit for, the defective product. This warranty excludes any expense for removal or reinstallation of any defective product and any other incidental, consequential, or punitive damages.
PAGE 2
Return Material Policy Consistent with general industry practices, all products are shipped at the customer’s risk. Shipments should be carefully inspected before signing a receipt. A signed bill of lading or delivery receipts with no exceptions noted will indicate that the count, description and condition of products are satisfactory. Customer must obtain a Return Material Authorization (RMA) number and return instructions from Charlotte Pipe.