How to Guide

72
Plastics Technical Manual
Number=MaximumRecommendedTemp.(°F)**CF=ConsultFactoryNR=NotRecommended••=IncompleteData
Chemical Name
PVC Viton ® EPDM NeopreneCPVC
Pipe & Fitting Materials
Recommended Max. Temp (°F)
Seal Materials
Recommended Max. Temp. (°F)
ABS
Acrylonitrile-Butadiene-Styrene Polyvinyl Chloride Type 1 Grade 1 Chlorinated Polyvinyl Chloride Type IV Grade 1
FlourocarbonElastomer(Viton®isaregisteredtrademarkoftheDuPontCo.)EthylenePropyleneDieneMonomer
**Maximumrecommendedtemperature,forchemicalresistance,undernormalconditions.§Non-pressure,vent-only,applicationswhenchemicalisingasform.
NicotinicAcid ................................... NR 140 •• •• 70 140
NitricAcid,10% ............................... 73 140 140 185 70 NR
NitricAcid,30% ............................... NR 140 120 160 70 NR
NitricAcid,40% ............................... NR NR 120 140 NR NR
NitricAcid,50% ............................... NR NR 73 120 NR NR
NitricAcid,70% .............................. NR NR 73 100 NR NR
NitricAcid,100% ............................. NR NR NR •• •• ••
NitricAcid,Fuming ........................... NR NR NR NR NR NR
Nitrobenzene .................................... NR NR NR 70 NR ••
Nitroglycerine ................................... NR NR NR •• •• ••
NitrousAcid,10% ............................. NR 73 •• 100 •• ••
NitrousOxide .................................... 73§ 73§ •• 70 •• NR
Nitroglycol ........................................ NR NR •• •• •• 70
NonionicSurfactants ......................... 140 140 NR 200 200 160
1-Octanol .......................................... NR •• NR •• •• ••
Ocenol ............................................... NR •• •• •• •• ••
Oils, Vegetable................................... NR 140 NR 200 NR ••
Oils, Sour Crude ................................ •• •• NR •• •• ••
Oleic Acid .......................................... 140 140 180 185 70 70
Oleum .............................................. NR NR NR NR NR NR
Olive Oil ............................................ 73 140 NR 150 •• 140
OxalicAcid(Sat’d) ............................ •• 140 140 100 150 100
OxalicAcid,20%............................... 73 140 180 100 150 100
OxalicAcid,50%............................... •• 140 73 100 150 100
Oxygen .............................................. 140§ 140§ 180§ 185 200 140
Ozone ................................................ 140§ 140§ 180§ 185 200 NR
OzonizedWater ................................. •• •• •• •• •• ••
Palm Oil ............................................ •• •• •• 70 NR ••
PalmiticAcid,10% ........................... 73 140 73 185 70 NR
PalmiticAcid,70% ........................... NR NR 73 185 •• NR
Paraffin ............................................. 73 140 •• 200 NR 140
Peanut Oil ......................................... •• •• •• 150 NR ••
Pentachlorophenol ............................. NR NR NR 200 NR NR
Peppermint Oil .................................. NR 73 73 73 73 73
PeraceticAcid,40% ......................... NR NR NR •• •• ••
DESIGN & ENGINEERING DATA
Chemical Resistance
The following table gives the chemical resistance of ABS, PVC and CPVC thermoplastic piping materials and three commonly
used seal materials. The information shown is based upon laboratory tests conducted by the manufacturers of the materials, and
it is intended to provide a general guideline on the resistance of these materials to various chemicals. NOTICE: This table is not
a guarantee, and any piping systems using products made of these materials should be tested under actual service conditions to
determine their suitability for a particular purpose. See website for most current data: www.charlottepipe.com