Dimensions Guide

ManualsBrandsCharlotte Pipe ManualsPVC DWV FittingsPVC 00106 1000

Charlotte and Charlotte Pipe are registered trademarks of Charlotte Pipe and Foundry Company.

LIMITED WARRANTY

Charlotte Pipe and Foundry Company

(Charlotte Pipe

) Products are warranted to be free from

manufacturing defects and to conform to currently applicable ASTM standards for a period of

ﬁve (5) years from date of delivery. Buyer’s remedy for breach of this warranty is limited to

replacement of, or credit for, the defective product. This warranty excludes any expense for removal

or reinstallation of any defective product and any other incidental, consequential, or punitive

damages. This limited warranty is the only warranty made by seller and is expressly in lieu

of all other warranties, express and implied, including any warranties of merchantability

and ﬁtness for a particular purpose. No statement, conduct or description by Charlotte Pipe

or its representative, in addition to or beyond this Limited Warranty, shall constitute a warranty.

This Limited Warranty may only be modiﬁed in writing signed by an ofﬁcer of Charlotte Pipe.

This Limited Warranty will not apply if:

1) The Products are used for purposes other than their intended purpose as deﬁned by local

plumbing and building codes, and the applicable ASTM standard.

2) The Products are not installed in good and workmanlike manner consistent with normal

industry standards; installed in compliance with the latest instructions published by Charlotte

Pipe and good plumbing practices; and installed in conformance with all applicable plumbing,

ﬁre and building code requirements.

3) This limited warranty does not apply when the products of Charlotte Pipe are used with the

products of other manufacturers that do not meet the applicable ASTM or CISPI standards

or that are not marked in a manner to indicate the entity that manufactured them.

4) In hubless cast iron installations, this warranty will not apply if products are joined with

unshielded hubless couplings. Charlotte Pipe requires that its hubless cast iron pipe and ﬁttings

be joined only with shielded hubless couplings manufactured in accordance with CISPI 310,

ASTM C 1277 and certiﬁed by NSF

International or with Heavy Duty Couplings meeting

ASTM C 1540.

5) The Products fail due to defects or deﬁciencies in design, engineering, or installation of the

piping system of which they are a part.

6) The Products have been the subject of modiﬁcation; misuse; misapplication; improper

maintenance or repair; damage caused by the fault or negligence of anyone other than

Charlotte Pipe; or any other act or event beyond the control of Charlotte Pipe.

7) The Products fail due to the freezing of water in the Products.

8) The Products fail due to contact with chemical agents, ﬁre stopping materials, thread sealant,

plasticized vinyl products, or other aggressive chemical agents that are not compatible.

9) Pipe outlets, sound attenuation systems or other devices are permanently attached to the

surface of Charlotte

PVC, ABS or CPVC products with solvent cement or adhesive glue.

Charlotte Pipe products are manufactured to the applicable ASTM or CISPI standard. Charlotte

Pipe and Foundry cannot accept responsibility for the performance, dimensional accuracy, or

compatibility of pipe, ﬁttings, gaskets, or couplings not manufactured or sold by Charlotte Pipe

and Foundry.

Any Charlotte Pipe products alleged to be defective must be made available to Charlotte Pipe at

the following address for veriﬁcation, inspection and determination of cause:

Charlotte Pipe and Foundry Company

Attention: Technical Services

2109 Randolph Road

Charlotte, North Carolina 28207

Purchaser must obtain a return materials

authorization and instructions for return

shipment to Charlotte Pipe of any product

claimed defective or shipped in error.

Any Charlotte Pipe product proved to be

defective in manufacture will be replaced

F.O.B. point of original delivery, or credit

will be issued, at the discretion of Charlotte

Pipe.

4/24/15

Testing with or use of compressed air or gas in PVC / ABS

/ CPVC / Cast Iron pipe or fittings can result in explosive

failures and cause severe injury or death.

• NEVER test with or transport/store

compressed air or gas in PVC / ABS /

CPVC / Cast Iron pipe or fittings.

• NEVER test PVC / ABS / CPVC / Cast

Iron pipe or fittings with compressed

air or gas, or air over water boosters.

• ONLY use PVC / ABS / CPVC / Cast Iron

pipe or fittings for water or approved

chemicals.

• Refer to warnings on PPFA’s website

and ASTM D 1785.