How to Guide
20
Plastics Technical Manual
GENERAL INFORMATION
SUBMITTAL FOR CHARLOTTE PIPE
®
PVC SDR 35 GRAVITY SEWER PIPE
Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.
FO-SUB-PVC-SDR-35 (5-2-18)
Date: ________________
Job Name: ______________________________ Location: _______________________________
Engineer: _______________________________ Contractor: ______________________________
Scope:
This specication covers PVC Standard Dimensional Ratio (SDR) 35 PSM pipe for gravity sewer and surface water
applications with a pipe stiffness of 46. This systems is intended for gravity applications where the operating temperature
will not exceed 140°F.
Specication:
Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class of 12364 as identied
in ASTM D 1784. The requirement of this specication are intended to provide pipe suitable for non-pressure drainage and
surface water.
PVC SDR 35 PSM pipe shall conform to ASTM D 3034 for gasket or solvent-weld pipe with a minimum pipe stiffness of 46.
Gaskets shall conform to ASTM F 477. The term “PSM” is not an acronym, but rather an arbitrary designation for a product
having certain dimensions.
Installation:
Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall conform to
all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance with ASTM D 2321
and ASTM F 1668. Solvent cement joints shall be made in a two-step process with primer conforming to ASTM F 656 and
solvent cement conforming to ASTM D 2564. The system shall be protected from chemical agents, re-stopping materials,
thread sealant, plasticized-vinyl products or other aggressive chemical agents not compatible with PVC compounds. The
system shall be hydrostatically tested after installation WARNING! Never test with or transport/store compressed air or gas
in PVC pipe or ttings. Doing so can result in explosive failures and cause severe injury or death.
Referenced Standards:
ASTM D 1784 Rigid Vinyl Compounds
ASTM D 3034 PVC Gravity Sewer Pipe (SDR) 35 PS 46
ASTM D 2564 Solvent Cements for PVC Pipe and Fittings
ASTM D 2321 Underground Installation of Thermoplastic Pipe (non-pressure applications)
ASTM F 477 Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM F 656 Primers for PVC Pipe and Fittings
ASTM F 1668 Procedures for Buried Plastic Pipe
Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • (800) 438-6091 • www.charlottepipe.com
PVC SDR 35 PSM Pipe
ASTM D 3034 & ASTM F 477
SDR-35 SOLVENT WELD - PS 46
S/M 6004 4”x10’ 04008 600’ 10’-0” 108.3 4.215 .120
S/M 6004 4”x20’ 04009 1200’ 20’-0” 108.3 4.215 .120
S/M 6006 6”x10’ 04013 280’ 10’-0” 241.7 6.275 .180
S/M 6006 6”x20’ 04014 560’ 20’-0” 241.7 6.275 .180
PART NO. NOM. SIZE UPC # QTY. PER LAYING WT. PER AVG. OD MIN. WALL
611942- SKID LENGTH 100 FT. (LBS.) (IN.) (IN.)
SDR-35 GASKETED - PS 46
PART NO. NOM. SIZE UPC # QTY. PER LAYING WT. PER AVG. OD MIN. WALL
611942- SKID LENGTH 100 FT. (LBS.) (IN.) (IN.)
S/M 6004G 4”x14’ 11920 840’ 14’-0” 110.4 4.215 .120
S/M 6004G 4”x20’ 04012 1200’ 20’-0” 109.7 4.215 .120
S/M 6006G 6”x14’ 11921 392’ 14’-0” 249.6 6.275 .180
S/M 6006G 6”x20’ 04016 560’ 20’-0” 247.0 6.275 .180
S/M 6008G 8”x14’ 11922 140’ 14’-0” 451.0 8.400 .240
Weight is approximate and is for shipping purposes only.
PVC Sewer Pipe
PVC SDR 35 PSM Pipe
ASTM D 3034 & ASTM F 477
Meets All Requirements of ASTM D 3034.
SDR 35 Gaskets meet or exceed ASTM F 477. Gasketed joints meet ASTM D 3212.