Installation Guide
71
Number=MaximumRecommendedTemp.(°F)**CF=ConsultFactoryNR=NotRecommended••=IncompleteData
Chemical Name
PVC Viton ® EPDM NeopreneCPVC
Pipe & Fitting Materials
Recommended Max. Temp (°F)
Seal Materials
Recommended Max. Temp. (°F)
ABS
Acrylonitrile-Butadiene-Styrene Polyvinyl Chloride Type 1 Grade 1 Chlorinated Polyvinyl Chloride Type IV Grade 1
FlourocarbonElastomer(Viton®isaregisteredtrademarkoftheDuPontCo.)EthylenePropyleneDieneMonomer
**Maximumrecommendedtemperature,forchemicalresistance,undernormalconditions.§Non-pressure,vent-only,applicationswhenchemicalisingasform.
Hydroquinone .................................... •• 140 •• 185 NR NR
HydroxylamineSulfate ...................... •• 140 •• •• 73 73
HypochlorousAcid ............................ 73 140 CF 73 73 ••
Iodine ............................................... NR NR NR 73 73 NR
IodineSolution,10% ......................... NR NR NR 200 150 ••
Iodine in Alcohol ............................... NR NR NR •• •• ••
Iron Salts .......................................... •• •• 180 •• •• ••
Isopropanol ....................................... NR 140 NR •• •• ••
Isopropyl Alcohol ............................... NR 140 140 160 160 73
Isopropyl Ether ................................. NR NR NR NR NR NR
Isooctane .......................................... NR NR NR 185 NR 73
Jet Fuel ............................................. NR NR NR 200 NR NR
Kerosene ........................................... NR NR NR 200 NR 73
Ketones ............................................. NR NR NR NR NR NR
Kraft Liquor ...................................... 73 140 180 100 •• 73
LacticAcid,25% ............................... NR 140 100 200 140 73
LacticAcid,80% ............................... NR 100 73 200 140 73
Lard Oil ............................................ 73 140 NR 185 NR 73
Lauric Acid ....................................... •• 140 •• 100 •• ••
Lauryl Chloride ................................. •• 140 •• 200 140 ••
Lead Acetate ..................................... •• 140 180 NR 200 160
Lead Chloride .................................... •• 140 180 140 NR 73
LeadNitrate ...................................... •• 140 180 200 175 140
Lead Sulfate ...................................... •• 140 180 200 200 140
Lemon Oil ......................................... •• 140 NR 200 NR 73
Ligroine ............................................ NR NR NR 100 •• 73
Lime Sulfur ....................................... •• 140 180 185 200 100
Limonene .......................................... •• •• NR •• •• ••
Linoleic Acid ..................................... •• 140 180 140 73 ••
Linoleic Oil ........................................ •• 140 180 73 •• ••
Linseed Oil ........................................ 73 140 NR 200 73 73
Linseed Oil, Blue ............................... 73 73 NR 200 •• ••
Liqueurs ............................................ NR 140 NR •• 200 160
Lithium Bromide (Brine) .................... •• 140 180 200 •• ••
Lithium Chloride ............................... •• 140 180 140 100 ••
DESIGN & ENGINEERING DATA
The following table gives the chemical resistance of ABS, PVC and
CPVC thermoplastic piping materials and three commonly used seal
materials. The information shown is based upon laboratory tests
conducted by the manufacturers of the materials, and it is intended
to provide a general guideline on the resistance of these materials
to various chemicals. NOTICE: This table is not a guarantee, and
Chemical Resistance
PVC, ABS and CPVC piping systems have very different
chemical resistance. Review manufacturer's literature for
all chemicals coming into contact with the piping materials
prior to use.
any piping systems using products made of these materials should be tested under actual service conditions to determine their
suitability for a particular purpose. See website for most current data: www.charlottepipe.com