Installation Guide
75
Number=MaximumRecommendedTemp.(°F)**CF=ConsultFactoryNR=NotRecommended••=IncompleteData
Chemical Name
PVC Viton ® EPDM NeopreneCPVC
Pipe & Fitting Materials
Recommended Max. Temp (°F)
Seal Materials
Recommended Max. Temp. (°F)
ABS
Acrylonitrile-Butadiene-Styrene Polyvinyl Chloride Type 1 Grade 1 Chlorinated Polyvinyl Chloride Type IV Grade 1
FlourocarbonElastomer(Viton®isaregisteredtrademarkoftheDuPontCo.)EthylenePropyleneDieneMonomer
**Maximumrecommendedtemperature,forchemicalresistance,undernormalconditions.§Non-pressure,vent-only,applicationswhenchemicalisingasform.
‡Mustusesolventcementspeciallyformulatedforhypochloriteorcausticchemicalservice(IPSWeld-On724orequal).
PhosphoricAcid,10% ....................... 73 140‡ 180‡ 200 140 140
PhosphoricAcid,50% ....................... NR 140‡ 180‡ 160 160 160
PhosphoricAcid,85% ....................... NR 140‡ 180‡ 160 160 160
Phosphoric Anhydride ........................ •• 73 73 •• •• ••
Phosphorous Pentoxide ...................... •• 73 180 200 200 ••
Phosphorous, Red .............................. NR 70 •• •• •• ••
Phosphorus Trichloride ...................... NR NR NR •• •• NR
Phosphorous,Yellow .......................... NR 73 •• •• •• ••
Photographic Solutions ..................... •• 140 180 185 •• 100
PhthalicAcid,10% ........................... 73 73 •• 140 •• NR
Picric Acid ........................................ NR NR NR 140 140 70
Pine Oil ............................................. NR NR NR 73 NR NR
Plating Solutions, Brass ..................... •• 140 180 140 73 140
Plating Solutions, Cadmium ............... •• 140 180 180 180 140
Plating Solutions, Chrome ................. •• 140 180 180 180 NR
Plating Solutions, Copper .................. •• 140 180 180 180 140
Plating Solutions, Gold ...................... •• 140 180 180 73 73
Plating Solutions, Indium .................. •• •• •• 140 73 140
Plating Solutions, Lead ...................... •• 140 180 180 180 140
PlatingSolutions,Nickel ................... •• 140 180 180 180 140
Plating Solutions, Rhodium ................ •• 140 180 73 120 73
Plating Solutions, Silver .................... •• 140 180 140 120 140
Plating Solutions, Tin ........................ •• 140 180 140 180 140
Plating Solutions, Zinc ...................... •• 140 180 140 73 180
POE Oils (Polyolester)........................ NR NR NR NR NR NR
Polyethylene Glycol (Carbowax) ......... •• 140 140 200 180 73
Polypropylene Glycol .......................... 73 NR NR 200 200 200
Potash ............................................... 140 140 180 200 170 160
Potassium Acetate ............................. •• •• 180 •• •• ••
Potassium Alum ................................ •• 140 180 200 200 160
Potassium Aluminum Sulfate ............. •• 140 180 200 200 160
Potassium Amyl Xanthate .................. •• 73 •• •• •• ••
Potassium Bicarbonate ...................... 140 140 180 200 170 160
Potassium Bichromate ....................... 140 140 180 200 170 ••
PotassiumBisulfate,Sat’d ................. •• 140 180 200 180 73
DESIGN & ENGINEERING DATA
The following table gives the chemical resistance of ABS, PVC and
CPVC thermoplastic piping materials and three commonly used seal
materials. The information shown is based upon laboratory tests
conducted by the manufacturers of the materials, and it is intended
to provide a general guideline on the resistance of these materials
to various chemicals. NOTICE: This table is not a guarantee, and
Chemical Resistance
PVC, ABS and CPVC piping systems have very different
chemical resistance. Review manufacturer's literature for
all chemicals coming into contact with the piping materials
prior to use.
any piping systems using products made of these materials should be tested under actual service conditions to determine their
suitability for a particular purpose. See website for most current data: www.charlottepipe.com