Installation Guide
76
Plastics Technical Manual
Number=MaximumRecommendedTemp.(°F)**CF=ConsultFactoryNR=NotRecommended••=IncompleteData
Chemical Name
PVC Viton ® EPDM NeopreneCPVC
Pipe & Fitting Materials
Recommended Max. Temp (°F)
Seal Materials
Recommended Max. Temp. (°F)
ABS
Acrylonitrile-Butadiene-Styrene Polyvinyl Chloride Type 1 Grade 1 Chlorinated Polyvinyl Chloride Type IV Grade 1
FlourocarbonElastomer(Viton®isaregisteredtrademarkoftheDuPontCo.)EthylenePropyleneDieneMonomer
**Maximumrecommendedtemperature,forchemicalresistance,undernormalconditions.§Non-pressure,vent-only,applicationswhenchemicalisingasform.
‡Mustusesolventcementspeciallyformulatedforhypochloriteorcausticchemicalservice(IPSWeld-On724orequal).
Potassium Borate .............................. 140 140 180 200 200 ••
Potassium Bromate............................ 140 140 180 200 •• 140
Potassium Bromide ............................ 140 140 180 200 170 160
Potassium Carbonate ......................... 140 140 180 200 170 160
Potassium Chlorate ............................ 140 140 180 140 140 100
Potassium Chloride ............................ 140 140 180 200 200 160
Potassium Chromate .......................... 140 140 180 200 170 70
Potassium Cyanide ............................. 140 140 180 185 140 160
Potassium Dichromate ....................... 140 140 180 200 170 ••
Potassium Ethyl Xanthate .................. •• 73 •• •• •• ••
Potassium Ferricyanide ...................... 140 140 180 140 140 150
Potassium Ferrocyanide ..................... 140 140 180 140 140 150
Potassium Fluoride ............................ 140 140 180 200 140 ••
PotassiumHydroxide,25% ................ 73 140‡ 180‡ NR 180 140
PotassiumHydroxide,50% ................ 73 140‡ 180‡ NR 180 NR
PotassiumHypochlorite ..................... •• 73‡ 180‡ 73 NR ••
Potassium Iodide ............................... •• 73 180 180 140 160
PotassiumNitrate .............................. 140 140 180 200 200 140
Potassium Perborate .......................... 140 140 180 73 73 73
PotassiumPerchlorate,(Sat’d) ........... 140 140 180 150 140 ••
PotassiumPermanganate,10% .......... 140 140 180 140 200 100
PotassiumPermanganate,25% .......... 140 140 180 140 140 100
PotassiumPersulphate,(Sat’d) ........... 73 140 180 200 200 140
Potassium Phosphate ......................... 73 •• 180 180 180 180
Potassium Sulfate .............................. 73 140 180 200 200 140
Potassium Sulfite ............................... 73 140 180 200 200 140
Potassium Tripolyphosphate ............... •• •• 180 100 •• 73
Propane ............................................ 140§ 140§ 73§ 73 NR 73
Propanol ........................................... NR 140 NR 200 200 140
Propargyl Alcohol .............................. NR 140 NR 140 140 NR
PropionicAcid,Upto2% .................. NR •• 180 •• •• NR
PropionicAcid,Over2% .................... NR •• NR •• •• NR
Propyl Alcohol ................................... NR 140 NR 200 200 140
Propylene Dichloride .......................... NR NR NR 73 NR NR
PropyleneGlycol,Upto25% ............. 73 140 180 200 200 73
DESIGN & ENGINEERING DATA
Chemical Resistance
The following table gives the chemical resistance of ABS, PVC and CPVC thermoplastic piping materials and three commonly
used seal materials. The information shown is based upon laboratory tests conducted by the manufacturers of the materials, and
it is intended to provide a general guideline on the resistance of these materials to various chemicals. NOTICE: This table is not
a guarantee, and any piping systems using products made of these materials should be tested under actual service conditions to
determine their suitability for a particular purpose. See website for most current data: www.charlottepipe.com