How to Guide

68
Plastics Technical Manual
Number=MaximumRecommendedTemp.(°F)**CF=ConsultFactoryNR=NotRecommended••=IncompleteData
Acrylonitrile-Butadiene-Styrene Polyvinyl Chloride Type 1 Grade 1 Chlorinated Polyvinyl Chloride Type IV Grade 1
FlourocarbonElastomer(Viton®isaregisteredtrademarkoftheDuPontCo.)EthylenePropyleneDieneMonomer
**Maximumrecommendedtemperature,forchemicalresistance,undernormalconditions.§Non-pressure,vent-only,applicationswhenchemicalisingasform.
‡Mustusesolventcementspeciallyformulatedforhypochloriteorcausticchemicalservice(IPSWeld-On724orequal).
Glycol,Propylene,Upto25% ............ 73 140 180 200 200 73
Glycol,Propylene,Upto50% ............ 73 140 NR 200 200 73
Glycolic Acid ..................................... •• 140 NR NR •• 73
Glycol Ethers ..................................... NR 140 NR •• •• ••
GrapeSugar,Juice ............................ 73 140 180 185 200 160
Green Liquor .................................... 140 140 180 •• 150 70
HalocarbonsOils ............................... NR NR NR 200 NR NR
Heptane
............................................ 73 140 NR 185 NR 73
Hexane
.............................................. NR 73 73 73 NR 73
Hexanol
............................................ NR 100 NR 160 NR 73
HydraulicOil ..................................... NR 73 •• 200 NR 73
Hydrazine .......................................... NR NR NR NR 70 ••
HydrobromicAcid,Dilute ................... 73 140 180 185 200 73
HydrobromicAcid,20% .................... 73 140 73 185 140 73
HydrobromicAcid,50% .................... NR 140 73 185 140 73
HydrochloricAcid,Dilute ................... 73 140 180 200 140 73
HydrochloricAcid,20% ..................... NR 140‡ 180‡ 200 140 73
HydrochloricAcidConc.,37% ........... NR 140‡ 180‡ 160 100 73
HydrocyanicAcid,10% ..................... 140 140 •• 185 200 ••
HydrouoricAcid,<10% .................. NR 140 140 150 73 100
HydrouoricAcid,30% .................... NR 73 140 200 NR NR
HydrouoricAcid,40% ..................... NR 73 NR 100 NR NR
HydrouoricAcid,50% ..................... NR NR NR 73 NR NR
HydrouoricAcid,100% ................... NR NR NR NR NR NR
HydrouosilicicAcid,50%................ NR 140 140 200 140 ••
Hydrogen .......................................... 140§ 140§ 73§ 200 200 160
HydrogenCyanide .............................. •• 140 •• •• •• 73
HydrogenFluoride ............................. NR NR NR NR 73 NR
HydrogenPeroxide,Dilute ................. 73 140 73 200 73 NR
HydrogenPeroxide,36% ................... NR 140 73 200 NR NR
HydrogenPeroxide,50% ................... NR 140 73 200 NR NR
HydrogenPeroxide,90% .................. NR NR NR 200 NR NR
HydrogenPhosphide ......................... •• 140 •• •• 73 ••
HydrogenSulde,Dry ....................... •• 140 180 140 100 NR
HydrogenSulde,AqeousSol. ........... •• 140 180 140 100 NR
Chemical Name
PVC Viton ® EPDM NeopreneCPVC
Pipe & Fitting Materials
Recommended Max. Temp (°F)
Seal Materials
Recommended Max. Temp. (°F)
ABS
DESIGN & ENGINEERING DATA
Chemical Resistance
The following table gives the chemical resistance of ABS, PVC and CPVC thermoplastic piping materials and three commonly
used seal materials. The information shown is based upon laboratory tests conducted by the manufacturers of the materials, and
it is intended to provide a general guideline on the resistance of these materials to various chemicals. NOTICE: This table is not
a guarantee, and any piping systems using products made of these materials should be tested under actual service conditions to
determine their suitability for a particular purpose. See website for most current data: www.charlottepipe.com