How to Guide

14
Plastics Technical Manual
GENERAL INFORMATION
SUBMITTAL FOR CHARLOTTE PIPE
®
RePVC
®
- PVC SCHEDULE 40 PIPE
WITH RECYCLED CONTENT AND PVC DWV FITTING SYSTEM
RePVC, Charlotte Pipe, and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.
FO-SUB-RePVC (9-11-17)
Date: ________________
Job Name: ______________________________ Location: _______________________________
Engineer: _______________________________ Contractor: ______________________________
Scope:
This specication covers PVC Schedule 40 pipe with recycled content and PVC DWV ttings used in sanitary drain, waste,
and vent (DWV), sewer and storm drainage applications. This system is intended for use in non-pressure applications
where the operating temperature will not exceed 140°F.
Specication:
Inside and outside layers of pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a
minimum cell class of 11432 per ASTM D 4396. Center layer of pipe shall be manufactured from recycled PVC compounds
with a minimum cell class of 11211 per ASTM D 4396. Fittings shall be manufactured from virgin rigid PVC (polyvinyl
chloride) vinyl compounds with a cell class of 12454 as identied in ASTM D 1784.
Center layer of pipe shall be comprised of 100% recycled material and make up 30 – 80% of the pipe’s overall wall thickness.
Coextruded PVC pipe with recycled content shall be Schedule 40 iron pipe size (IPS) conforming to ASTM F 1760. Injection-
molded PVC DWV ttings shall conform to ASTM D 2665. Fabricated PVC DWV ttings shall conform to ASTM F 1866. All
pipe and ttings shall be manufactured in the United States. All systems shall utilize a separate waste and vent system. Pipe
and ttings shall conform to NSF International Standard 14.
Installation:
Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall conform to
all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance with ASTM D 2321
and ASTM F 1668. Solvent cement joints shall be made in a two-step process with primer conforming to ASTM F 656 and
solvent cement conforming to ASTM D 2564. The system shall be protected from chemical agents, re-stopping materials,
thread sealant, plasticized-vinyl products, or other aggressive chemical agents not compatible with PVC compounds.
Systems shall be hydrostatically
tested after installation. WARNING! Never test with or transport/store compressed air or gas in
PVC pipe or ttings. Doing so can result in explosive failures and cause severe injury or death.
Referenced Standards:
ASTM D 4396 Compounds for Cellular Core Pipe
ASTM F 1760 Co-Extruded PVC Pipe with Recycled Content
ASTM D 2665 PVC Drain, Waste, and Vent Fittings
ASTM D 2564 Solvent Cements for PVC Pipe and Fittings
ASTM D 2321 Underground Installation of Thermoplastic Pipe (non-pressure applications)
ASTM F 656 Primers for PVC Pipe and Fittings
ASTM F 1668 Procedures for Buried Plastic Pipe
ASTM F 1866 Fabricated PVC DWV Fittings
NSF Standard 14 Plastic Piping Components and Related Materials
Not all tting patterns shown
Combination Wye
& Eighth Bend
Double
Sanitary Tee
Eighth Bend
Quarter Bend
Coupling
Cleanout Tee
w/Plug
RePVC® DWV Pipe
Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • [phone] • www.charlottepipe.com
PVC Schedule 40 DWV Pipe with Recycled Content
(For Non-Pressure Applications)
PVC 15112 1
1
⁄ 2 ” x 20’ 11744 3440’ 1.900 .145 50.7
PVC 15200 2” x 20’ 11745 2220’ 2.375 .154 68.1
PVC 15300 3” x 20’ 11746 920’ 3.500 .216 141.2
PVC 15400 4” x 20’ 11748 1200’ 4.500 .237 201.2
PVC 15600 6” x 20’ 11749 560’ 6.625 .280 353.7
PVC 15800 8” x 20’ 11984 360’ 8.625 .322 544.6
PVC SCHEDULE 40 (WHITE) PLAIN END PVC 1120 ASTM D 2665
PVC SCHEDULE 40 (WHITE) PLAIN END ASTM F 1760
PART NO. NOM. SIZE UPC # QTY. PER AVG. OD MIN. WALL WT. PER 100 FT.
611942- SKID (IN.) (IN.) (LBS.)
NSF Listed. Meets All Requirements of ASTM D 4396 and ASTM F 1760.