How to Guide
98
Plastics Technical Manual
NOTICE: Charlotte does not recommend pipe joint compounds,
pastes or lubricants for thermoplastic pipe as the use of an
incompatible compound may result in the degradation or
failure of the plastic pipe or fittings.
Piping systems differ in chemical resistance. Pipe or fittings
may be damaged by contact with products containing
incompatible chemicals resulting in property damage.
L[h_\oj^WjfW_dji"j^h[WZi[WbWdji"bkXh_YWdji"fbWij_Y_p[Z
FL9 fheZkYji" \eWc _dikbWj_edi" YWkbai" b[Wa Z[j[Yjehi"
_di[Yj_Y_Z[i" j[hc_j_Y_Z[i" Wdj_\h[[p[ iebkj_edi" f_f[
ib[[l[" \_h[ijef cWj[h_Wbi eh ej^[h cWj[h_Wbi Wh[
Y^[c_YWbboYecfWj_Xb[m_j^78I"FL9eh9FL9$
:edejki[[Z_Xb[e_biikY^Wi9h_iYe
®
\ehbkXh_YWdj$
H[WZ WdZ \ebbem Y^[c_YWb cWdk\WYjkh[h½i b_j[hWjkh[
X[\eh[ki_d]m_j^f_f_d]cWj[h_Wbi$
Exceeding recommended torque for threaded connections
may result in component damage, system failure and
property damage.
5SBEFNBSLPGUIF&*%V1POU$PNQBOZ
Procedure for Cutting Threads in Schedule
80 Pipe
1. Cutting
The pipe must be cut square using a power saw, a miter box,
or a plastic pipe cutter. Burrs should be removed using a knife
or deburring tool.
2. Threading
Threads can be cut using either hand held or power threading
equipment. The cutting dies should be clean, sharp, and in good
condition. Special dies for cutting plastic pipe are available
and are recommended.
8IFOVTJOHBIBOEUISFBEFSUIFEJFTTIPVMEIBWFB×UP×
OFHBUJWFGSPOUSBLF8IFOVTJOHBQPXFSUISFBEFSUIFEJFT
should have a 5° negative front rake and the die heads should
be self-opening. A slight chamfer to lead the dies will speed
QSPEVDUJPO)PXFWFS UIFEJFTTIPVME OPU CF ESJWFOBUIJHI
speeds or with heavy pressure.
8IFO VTJOH B IBOE IFME UISFBEFS UIF QJQF TIPVME CF IFME
in a pipe vise. To prevent crushing or scoring of the pipe, a
protective wrap such as emery paper, canvas, rubber, or a light
metal sleeve should be used.
Insert a tapered plug into the end of the pipe to be threaded.
This plug will provide additional support and prevent distortion
of the pipe in the threading area.
It is recommended that a water soluble machine oil, chemically
compatible with PVC and CPVC, be used during the threading
operation. Also, clearing the cuttings from the die is highly
recommended.
Do not over-thread the pipe. Consult the diagram and table
TIPXJOH"45.'EJNFOTJPOTGPS"NFSJDBO4UBOEBSE
Taper pipe threads. Periodically check the threads with a ring
gauge to ensure that the threads are accurate. The tolerance
JTß
1
⁄2 turns.
Installation of Threaded Connections
.BLF TVSF UIF UISFBET BSF DMFBO $IBSMPUUF 1JQF
SFDPNNFOET 5FGMPO UBQF BT B TFBMBOU GPS UISFBEFE
DPOOFDUJPOT 6TF B HPPE RVBMJUZ 5FnPOUBQF XIJDIIBT
NJOJNVNEFOTJUZwUIJDLFMPOHBUJPOBOE
chemically inert.
8SBQ UIF 5FnPO UBQF BSPVOE UIF FOUJSF MFOHUI PG UIF
UISFBET TUBSU XJUI UXP XSBQT BU UIF FOE BOE XSBQBMM
UISFBETPWFSMBQQJOHIBMGUIFXJEUIPGUIFUBQF8SBQJO
the direction of the threads on each wind.
.BLF UISFBEFE DPOOFDUJPOT BOE IBOE UJHIUFO 'VSUIFS
tighten approximately two turns past hand tight using a
strap wrench only. Do not use common wrenches or tools
designed for metallic pipe systems.