Owner’s Manual Indoor Lighting Fixture Installation Instructions Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para futura referencia:
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHT FIXTURE Congratulations on your purchase. This fixture has been designed to give you many years of beauty and service. NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1). WARRANTY INFORMATION This Fixture is warranted against defects in material and workmanship for a period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or implied.
FIGURE 1. *OUTLET BOX SCREWS (P) *OUTLET BOX (J) WIRE CONNECTORS (G) OUTER HOLES (O) GROUND WIRE ADDITIONAL SUPPORT HOLES (F) SIDE HOLE (I) RETAINING SCREW (B) MOUNTING HOLES (D) MOUNTING PLATE (C) SCREW (K) WALL ANCHORS (E) GREEN GROUNDING SCREW (H) FACE PLATE (A) HOLDER (M) THUMB SCREWS (N1) GLASS SHADE (L) CAP NUTS (B1) RETAINING RING (N) Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.
MOUNTING AND WIRING INSTRUCTIONS NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications. 1. Beginning at sides and working at an angle, peel protective coating (if applicable) from face plate (A) (see fig. 1). 2. Remove retaining screws (B) from top of face plate (A) or cap nuts (B1) from face plate (A)and separate mounting plate (C) from face plate (A). 3.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION INTÉRIEURE Félicitations ! Vous avez acheté un produit. Cet appareil d'éclairage a été conçu pour durer de nombreuses années. NOTA : Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces y sont avant de mettre l’emballage au rebut (voir fig. 1). MISE EN GARDE: L'ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES. Lisez ces instructions et suivez-les exactement comme illustré.
FIGURE 1.
INSTRUCTIONS DE MONTAGE ET DE RACCORDEMENT NOTA : Underwriters Laboratories (UL) n’exige pas que tous les appareils d’éclairage comportent des fils de mise à la terre. Ces appareils satisfont cependant à toutes les spécifications UL. 1. En commençant par les côtés et en travaillant en angle, enlevez la couche protectrice (s’il y a lieu) de la plaque avant (A) (voir fig. 1). 2.
INSTRUCCIONES DE MONTAJE PARA EL ARTEFACTO DE ILUMINACIÓN PARA INTERIORES Le felicitamos por comprar este producto. Este producto ha sido diseña- do para brindarle muchos años de belleza y servicio. NOTA: Extraiga cuidadosamente el artefacto y las piezas. Verifique que contenga todas las partes requeridas (consulte la figura 1) antes de descartar los materiales de empaque. ADVERTENCIA: UNA DESCARGA ELÉCTRICA PODRÍA CAUSAR LESIONES. Lea y siga las instrucciones exactamente como se indica.
FIGURA 1.
INSTRUCCIONES DE MONTAJE Y CABLEADO NOTA: Underwriters Laboratories (U.L.) no requiere que todos los artefactos tengan cables de tierra. Estos artefactos cumplen con todas las especificaciones U.L. 1. Comenzando desde los lados y trabajando en forma de ángulo, quite el recubrimiento protector (si corresponde) de la placa delantera (A) (vea la Fig. 1). 2.
FIGURE 2. GROUP A: CONNECT TO BLACK HOUSE WIRE GROUP B: CONNECT TO WHITE HOUSE WIRE BLACK WHITE WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER BROWN, GOLD OR BLACK WITHOUT TRACER BROWN, GOLD OR BLACK WITH TRACER NOTE: When parallel wire (SPT I & SPT II) is used; the neutral wire is square shaped and ridged, and the hot wire will be round in shape and smooth. (See below.) WARNING Turn off electricity to the mounting site before beginning installation.
CLEANING AND CARE To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Extend-A-Finish Laquer Conditioner, is recommended once a year to clean, condition, and protect fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
