Installation & Assembly

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE
IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling, which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this
fixture.
NOTE: This fixture can be mounted in two ways: SEMI FLUSH
OR PENDANT.
STEP 1: Hook the hook of arm (I) to the hook (H). Hook the
other hook of arm (I) to the hook (J) of frame.
PENDANT INSTALLATION
CAUTION: Please buy one hardware bag for pendant
installation (not provide) and assembly according to
ASSEMBLY INSTRUCTION SHEET OF PART BAG.
SEMI FLUSH INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Secure the mounting bar (A) to outlet box with the
outlet box screws (B).
STEP 2: Thread the nut (D) onto the nipple (E). Insert the lock
washer (C) and thread the nipple (E) into the
mounting bar (A), then secure with the nut (D).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the ground
wire from the fixture (if supplied) around the green
grounding screw, then connect it to ground wire from
the outlet box (if not fixed on the outlet box) using a
wire connector (not supplied). If ground wire from the
fixture is not supplied, wrap the ground wire (if not
fixed on the outlet box) from the outlet box around the
green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below:
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round
in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do
NOT twist wires together before using wire
connectors.
STEP 4: Fit a wire connector over the wires and screw the
connector clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you
can pull the connector off, carefully re-do steps 3 and
4 as above, and check again for a firm connection.
STEP 6: Connect the fixture wire from group B to the white
wire from the outlet box in the same manner. Make
sure no bare wires can be seen outside wire
connectors.
FINAL ASSEMBLY
STEP 1: (FOR SEMI FLUSH) After wires are connected, tuck
them carefully inside outlet box, then secure the
canopy (F) allowing the nipple (E) to protrude through
the holes in the canopy (F) and secure with the ball nut
(G).
STEP 2: Install light bulbs.(Please do not exceed the maximum
capacity recommended on the socket.)
STEP 3: Slide the glass (L) and the washer (M) onto the nipple
(K) and secure with the cap (N).
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.