Assembly Instruction

ManualsBrandsCharlton Home ManualsAll Ceiling LightsHardin 2 - Light 18'' Simple Bowl Semi Flush Mount

Table Of Contents

NOTE: 1.The fixture can be assembled as semi-flush OR hanging pendant .If assembling as

hanging pendant, the consumer needs to buy the pendant hardware kits separately.

2. Please consult a qualified electrician if you are not certain of the installation or service.

CAUTION: Before starting the installation or service, disconnect the power by turning off the

circuit breaker or by removing the fuse at the fuse box.

※ Installations for semi-flush

1. Carefully unpack the fixture, lay out all parts on a clean surface.

2. Fasten the mounting ring onto the outlet box by using provided 2 outlet box screws.

3. Place the tube over the nipple A, then screw the nipple A into the bushing A.

4. Tie the ground wires from fixture and from outlet box to the ground screw on the mounting strap.

Connect the wire without writing on it (with raised ribs) from the fixture to the white wire

(neutral wire) from the supply circuit. Connect the wire with writing on it from the fixture to the

black wire (live wire) from the supply circuit. Cover the connections using provided wire

connectors. Position wires back inside outlet box.

5. Place the canopy to the outlet box by aligning the protruding mounting screws all the way

through the canopy and tighten the fixture using lock nuts provided until fixture body is held

firmly.

6. Install the bulbs (Not included).

7. Screw the nipple B into the bushing B using the hex nut. Place the decorative pan, steel washer

A, plastic washer, shade, and bottom cover over the steel washer B, using the finial to secure them.

8. Turn on the power.

ASSEMBLY INSTRUCTION

Summary of content (4 pages)

PAGE 1
ASSEMBLY INSTRUCTION NOTE: 1.The fixture can be assembled as semi-flush OR hanging pendant .If assembling as hanging pendant, the consumer needs to buy the pendant hardware kits separately. 2. Please consult a qualified electrician if you are not certain of the installation or service. CAUTION: Before starting the installation or service, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. ※ Installations for semi-flush 1. 2. 3. 4. 5. 6. 7. 8.
PAGE 2
INSTRUCCIONES DE ENSAMBLAJE NOTA: 1. El producto puede ser ensamblado como semiflujo o colgante. Si se ensambla como colgante, el consumidor tiene que comprar el kit de instalación del pendiente. 2. Por favor, consulte con un electricista calificado en caso de que no esté seguro de la instalación. PRECAUCIÓN: Antes de comenzar la instalación del producto, desconecte la electricidad apagando el interruptor o retirando el fusible de la caja de fusibles. 1.
PAGE 3
ASSEMBLY INSTRUCTION Installations for hanging pendant 1. Carefully unpack the fixture, lay out all parts on a clean surface. 2. Fasten the mounting strap onto the outlet box by using provided 2 outlet box screws. 3. Fasten the loop to the nipple A. Fill holes of the canopy B with the Screws and Lock Nuts provided in the pendant hardware kits. 4. Place the tube over the nipple A, then screw the nipple A into the bushing A. 5. Using two pliers, twist open links at two ends of the chain as show.
PAGE 4
INSTRUCCIONES DE ENSAMBLAJE Instalaciones del colgante 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Desempaquetar cuidadosamente el producto, disponer todas las piezas sobre una superficie limpia. Fijar el soporte de montaje a la caja de tomacorrientes usando los dos tornillos de la caja de tomacorrientes que se proporcionan. Ajustar el lazo en la entrerrosca A. Llenar los agujeros del dosel B con los tornillos y las tuercas de bloqueo provistas en el kit del colgante.