ASSEMBLY INSTRUCTIONS Console NOTE TO CUSTOMERS: . For ease and speed of assemble we recommend that before you commence each step of the assembly that you identify all the parts required to complete that step. . ‘We recommend that where possible you allow sufficient space to assemble the item as close as possible to the place where it will be once assembled. . For the protection of your furniture we recommend that the product is placed on protected surfaces during assembly to prevent any damage.
To insert a cam lock: (Please read below instructions before assembling) Diagram A 1. Insert cam screw into hole as shown in diagram A . Diagram B Make sure not to insert the cam screw: Too deep as shown in figure B as this will cause the e cam screw to be misaligned and unable to W COMDR Also avoid inserting the cam screw too close to the surface of the hole as shown in figure C, as this will cause the cam lock to be too loose, and not interlock properly. Connect the panels together.
Al Quantity |A2, Quantity |A3, Quantity |A4, Quantity Left Side Panel Right Side Panel Middle Shelf Cross Bar A5, Quantity |A6. Quantity |AT. Quantity |A8. Quantity Left Shelf Right Shelf Top Panel Bottom Shelf A9. Quantity |A10. Quantity |ALL Quantity |A12. Quantity Left Divider Right Divider A13. Al4, Quantity of 2 — Right Door Drawer Front Manet Drawer Side Manet Drawer Back Panel Al7. Quantity |A18. Quantity |A19.
Hardware List Bl. Quantity B2, Quantity |B3. Quantity |B4. Quantity Cam lock Wood Dowel Screw Screw BS. Quantity |B6. Quantity |B7. Quantity |BS, Quantity Screw Door Knob Flower Agent B9. Quantity |B10. Quantity [Bll. Quantity |B12. Quantity Stopper Drawer Knob Anchor with Resew Anti-tip kit Step 1: B8: J=I masers Bo: =7 SEISMIC Stopper B9 to Cross Bar A4 and the bottom of Top Panel A7 using included Screws. Agents B8 to the bottom of Top Panel A7 using included Screws.
Step 2: Bl: & SETS B2: PCS Assemble Middle Shelf A3 & Cross Bar A4 to Left Divider using Cam locks B1 and Wood Dowels B2.
Step 4: Bl: & =Ct® TSETSE B2: PCS Assemble Shelf AS & A6 (L&R) to Dividers A9 & A10 (L&R) using Cam locks B1 and Wood Dowels B2, Step 5: Bl: & SETS B2: PCS Assemble Side Panels Al & A2 (L&R) to Shelf A5 & A6 (L&R) using Cam locks B1 and Wood Dowels B2.
Step 6: Bl: & BESTS B2: PCS Assemble Top Panel A7 to Left Panel A 1,Right Panel Leftist Divider A9 and Right Divider A10 using Cam locks B1 and Wood Dowels B2, Step 7: B3: T PCS Assemble Back Panel Al1 to the back of the unit using Screws B3.
Step 8: Attach and tighten Center Legs A18 to the bottom of Left Panel Aright Panel Leftist Divider A9 and Right Divider A10 as shown above. Step 9: Attach and tighten Bottom Legs A19 by inserting the legs throng the Bottom Shelf A8 and attach it to Center Legs Al8.
) L _u‘“ ‘IL-llDoors A12 & A13 (L&R) to Side Panels A1 & A2 (L&R) using Screws B4. Door Knob B6 and Flowers B7 to Door A12 & A13 (L&R) using include bolts as shown above. Step 11: B5: =g PCS BIO: ap.. 25ET Drawer Side Panels A15 to Drawer Back Panel A16 using Screws BS5, Drawer Bottom Panel A17 into grooves on Drawer Side Panels A15 and Drawer Back Panel A16. Drawer Front Panel A14 to Drawer Side Panels A15 using Screws BS. Drawer Knob B10 to Drawer Front Panel A14 using included Bolt.
Step Bll o o 1st Insert Drawers into the table. Page 10 of 11 For your safety, please attach the unit to the wall by Anchor with Screws B10 and Anti-tip kit B11.
Appendix: Dimension of Hardware in this Cam—bolt Bl. 916" e 38" B2.
