Installation & Assembly

ManualsBrandsCharlton Home ManualsCeiling LightsTilford 2 - Light Lantern Bowl Chandelier

Installation And Safety Instructions

Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to

this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________

Carefully remove the fixture from the carton and check that all parts

are included, as shown in figure 1. Be careful not to misplace

any of the screws or parts which are needed to install this fixture.

• Be sure the electricity to the system you are working on is turned off;

either the fuse removed or the circuit breaker set at off.

• Use of other manufacturers components will void warranty, listing and

create a potential safety hazard.

• To reduce the risk of fire, electric shock, or personal injury, mount to

outlet box or supporting system able to support the weight of the fixture.

•

If you are unclear as to how to proceed, contact a qualified electrician.

• You don’t need special tools to install this fixture.

•

Be sure to follow the steps in the order given.

• Under no circumstances should a fixture be hung on house electrical

ires, nor should a swag type fixture be installed on a ceiling which

contains a radiant type heating system.

•

Read instructions carefully.

• Save these instructions.

IMPORTANT SAFETY INSTRUCTIONS

BEFORE YOU BEGIN

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.

Do not use abrasive materials such as scouring pads or powders,

steel wool or abrasive paper.

Keep this sheet for future reference, and in case you need to order

replacement parts. Parts for this fixture can be ordered from place of

purchase. Be sure to use exact wording from illustration when

ordering parts.

CLEANING

ORDERING PARTS

Secur

e mounting bar (A) to outlet box with outlet box scr

ews (not

supplied). Thr

ead nut (B) on nipple (C) so that 5 threads ar

e exposed

above nut (B). Thread nipple (C) into mounting bar (A) and secure

with nut (B). Thread screw collar (E) to nipple (C).

Using 2 pairs of pliers or chain br

eaks, open one link of chain (S) and

connect it to the fixtur

e loop (I) at the top of the fixtur

e. Chain should

be opened outwards,

DO NOT TWIST.

IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.

STEP 2:

INSTALLATION

STEP 1:

FOR CHAIN HUNG

*OUTLET BOX

SCREWS

*WIRE CONNECTORS

SCREW COLLAR (E)

CANOPY (H)

MOUNTING BAR (A)

*GROUND WIRE

SCREW COLLAR

RING (G)

FIGURE 1 *NOT SUPPLIED

CHAIN (S)

FIXTURE LOOP (I)

NIPPLE (C)

NUT (B)

CAP NUTS (Y)

FLUSH

CANOPY (Z)

CHAIN

HUNG

DECORATIVE

RING (J)

STEP 3:

Slide the screw collar ring (G) and canopy (H), in that order, over

chain (S). Open one link on the other end of the chain (S) and attach

it to the screw collar (E) which has been mounted to the nipple (C).

BE SURE TO CLOSE ALL CHAIN LINKS COMPLETEL

Summary of content (2 pages)

PAGE 1
Installation And Safety Instructions Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________ IMPORTANT SAFETY INSTRUCTIONS • Be sure the electricity to the system you are working on is turned off; either the fuse removed or the circuit breaker set at off.
PAGE 2
FOR FLUSH MOUNT STEP 1: Thread mounting screws (K) into offset mounting bar (N). Run mounting screws (K) all the way down to their heads. Secure offset mounting bar (N) to the outlet box (raised side to top as illustrated) using outlet box screws (not supplied). FLUSH MOUNT STEP 2: Remove fixture loop (I) from flush canopy (Z). Feed fixture wires through center of flush canopy (Z). Secure flush canopy (Z) to fixture by installing lock washer and nut over fixture center nipple.