Assembly Instructions

ManualsBrandsCharlton Home Manuals3 Piece Kitchen & Dining Room SetsTeneyck 3 Piece Counter Height Drop Leaf Pub Table Set

ASSEMBLY INSTRUCTIONS

This page lists all the contents included in the box. Please take the time to identify

the hardware as well as the individual components to this product. As you unpack

and prepare for assembly, place the contents on a carpeted or padded area to

protect them from damage.

c l e a n i n g & c a r e

Treat surface with care. Surface is resistant to

scratches but is not scratch resistant. Clean surfaces with a dry or damp soft cloth.

Do not use abrasive cleaners. Hardware may loosen over time. Periodically check

that all connections are tight.

3PC Bistro Set, Black / Cherry Finish

Summary of content (21 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS 3PC Bistro Set, Black / Cherry Finish This page lists all the contents included in the box. Please take the time to identify the hardware as well as the individual components to this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage. c l e a n i n g & c a r e Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean surfaces with a dry or damp soft cloth.
PAGE 2
GENERAL INFORMATION, TIPS & TRICKS 1. Please read the assembly instructions prior to assembling this product. 2. To avoid damages, assemble this product on a non-abrasive surface such as carpet. 3. Make sure all bolts and nuts are tightly fastened before the product is used. 4. Not for commercial use. 5. Care: Wipe with a damp cloth. Use furniture polish or lemon oil on the wood as needed. Avoid prolonged exposure to moisture. Please make sure you have all parts before begining assembly.
PAGE 3
TABLE PARTS LIST A. TABLE TOP QTY: 1 PC C. TABLE LEG (RIGHT FRONT / LEFT BACK) QTY: 2 PCS E. TOP PANEL QTY: 1 PC G. MIDDLE PANEL QTY: 1 PC B. TABLE LEG (LEFT FRONT / RIGHT BACK) QTY: 2 PCS D. BOTTOM PANEL QTY: 1 PC F. SIDE PANEL QTY: 2 PCS H. DIVIDER PANEL QTY: 2 PCS I.
PAGE 4
CHAIR PARTS LIST J. CHAIR BACK FRAME QTY: 2 PCS L. SEAT FRAME QTY: 2 PCS N. CHAIR FRONT RIGHT LEG QTY: 2 PCS K. SEAT BOARD QTY: 2 PCS M. CHAIR FRONT LEFT LEG QTY: 2 PCS O. FRONT CROSSBAR QTY: 2 PCS P.
PAGE 5
TABLE HARDWARE LIST 1. BOLT 5/16" Dia x 2-1/2"L QTY: 8 PCS 3. FLAT WASHER QTY: 8 PCS 2. SPRING WASHER QTY: 8 PCS 4. BOLT 1/4" Dia x 2"L QTY: 4 PCS 5. CAM LOCK 6. METAL DOWEL SCREW QTY: 4 PCS 7. "T" NUT QTY: 4 PCS 8. WOOD DOWEL QTY: 4 PCS 9.
PAGE 6
CHAIR HARDWARE LIST 10. LONG BOLT 1/4" Dia x 3"L QTY: 8 PCS 3. FLAT WASHER QTY: 22 PCS 2. SPRING WASHER QTY: 22 PCS 11. SHORT BOLT 1/4" Dia x 1-3/4"L QTY: 6 PCS 13. WOOD SCREW 12. HEX NUT QTY: 8 PCS QTY: 24 PCS 14.
PAGE 7
TABLE ASSEMBLY INSTRUCTIONS REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 5 CAM LOCK 6 6 6 SKETCH 4 METAL DOWEL SCREW E QTY 4 6 F F 6 5 Diagram #1 5 5 5 E Diagram #2 1. Screw the 4 metal dowel screw (6) into the pre drilled plastic hole. Attach side panels (F) to the top panel (E) using 4 cam locks (5) and 4 metal dowel screws (6) as shown.
PAGE 8
TABLE ASSEMBLY INSTRUCTIONS F G F Diagram #3 2. Attach the middle panel (G) to the assembled from diagram #3 as shown.
PAGE 9
TABLE ASSEMBLY INSTRUCTIONS G H H Diagram #4 3. Attach the divider panels (H) into the groove on the middle panel (G) as shown.
PAGE 10
TABLE ASSEMBLY INSTRUCTIONS REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 4 BOLT SKETCH QTY 4 7 NUT 4 9 ALLEN KEY 1 9 4 4 4 Diagram #5 4 D 7 H 7 7 H 7 4. Attach bottom panel (D) to the assembled from diagram #5 using 4 "T" nut (7) and 4 bolts (4) as shown.Tightly fasten the bolts using Allen key (9).
PAGE 11
TABLE ASSEMBLY INSTRUCTIONS REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 8 WOOD DOWEL SKETCH QTY 4 8 8 8 C 8 B Diagram #6 D C B Diagram #7 5. Attach bottom panel (D) to the assembled from diagram #7 using wood dowel (8) as shown.
PAGE 12
TABLE ASSEMBLY INSTRUCTIONS REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 1 BOLT 2 SKETCH SPRING WASHER QTY 2 2 3 FLAT WASHER 2 9 ALLEN KEY 1 3 2 23 Diagram #8 6. Attach base panel (I) to table legs (B&C) using 2 spring washers (2), 2 flat washers (3), 2 bolts (1) as shown.Tightly fasten the bolts using Allen key (9).
PAGE 13
TABLE ASSEMBLY INSTRUCTIONS REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 1 BOLT SKETCH QTY 2 SPRING WASHER 2 2 3 FLAT WASHER 2 8 WOOD DOWEL 4 9 ALLEN KEY 1 B 8 3 C 8 2 3 1 2 F 1 9 Diagram #9 7. Attach table legs (B&C) to base panel (I) and side panel (F) using 4 wood dowel (8), 2 spring washers (2), 2 flat washers (3) and 2 bolts (1) as shown.Tightly fasten the bolts using Allen key (9).
PAGE 14
TABLE ASSEMBLY INSTRUCTIONS Diagram #10 8. turn the table base upright. Place the table top (A) on the table legs as shown.
PAGE 15
TABLE ASSEMBLY INSTRUCTIONS REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 1 BOLT 2 SPRING WASHER SKETCH QTY 2 2 3 FLAT WASHER 2 9 ALLEN KEY 1 Diagram #11 3 2 1 9 9. secure the table top (A) to the table base using 4 bolts (1), 4 spring washers (2) and 4 flat washers (3) as shown.Tightly fasten the bolts using Allen key (9).
PAGE 16
TABLE ASSEMBLY INSTRUCTIONS Diagram #12 10. The table is now ready for use.
PAGE 17
CHAIR ASSEMBLY INSTRUCTIONS Diagram #1 REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 2 SPRING WASHER SKETCH QTY 7 3 FLAT WASHER 7 10 LONG BOLT 4 11 SHORT BOLT 3 10 10 J 2 3 11 2 3 2 3 L 1. Attach seat frame (L) to back frame (J) using 7 spring washers (2), 7 flat washers (3), 3 short bolts (11) and 4 long bolts (10) as shown. Do not tighten at this point.
PAGE 18
CHAIR ASSEMBLY INSTRUCTIONS Diagram #2 REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 13 WOOD SCREW 13 13 13 SKETCH QTY 6 13 13 L K J 2. Place seat board (K) upside down on a non-abrasive table surface. The rear (tapered end) of the seat board (K) should be near the table edge. Hint: Protect the non-abrasive table surface and seat board (K) by laying a towel in-between the chair seat and table. 3. Place the assembled chair frame on the seat board (K) as shown. Attach with 6 wood screws (13).
PAGE 19
CHAIR ASSEMBLY INSTRUCTIONS Diagram #3 REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION SPRING WASHER 2 SKETCH QTY 4 3 FLAT WASHER 4 12 HEX NUT 4 14 OPEN END WRENCH 1 M O N P 12 2 3 L J 4. Attach the left and right front legs (M&N) to seat frame (L) using 4 spring washers (2), 4 flat washers (3), and 4 hex nuts (12) as shown. Do not tighten at this point. 5. Insert the front crossbar (O) into the oval holes of left and right front legs (M&N) as shown.
PAGE 20
CHAIR ASSEMBLY INSTRUCTIONS Diagram #4 REQUIRED HARDWARE IN THIS STEP NO. DESCRIPTION 13 WOOD SCREW 7 7 M 7 7 SKETCH QTY 6 N O 77 P L J 7. Turn the chair upright. Make sure the assembled chair unit is level and square. Tightly fasten all bolts with the open-end wrench (4). 8. Secure the front and side crossbars (P) to their chair legs with 6 wood screws (13). Note: Screwing the wood screws (13) to secure the front crossbar (O) by first.
PAGE 21
CHAIR ASSEMBLY INSTRUCTIONS Diagram #5 9. The Chair is now ready for use. 10. Repeat steps 1 to 8 to assemble the other chair.