Assembly Instructions

IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut off the power at the circuit breaker and
completely remove the old xture from the ceiling, including the old mounting strap.
1. Take the mounting strap assembly from the parts bag. Mounting strap (B) contains several threaded holes. Two of mounting screws (A)
should be attached to mounting strap (B). You may need to tighten nuts (C) that hold these screws in place. If the screws are not attached,
please hold canopy (G) up to mounting strap (B). Line up the holes in canopy (G) with the holes in mounting strap (B) and insert mounting
screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (G). Mounting screws (A) are long, so
please test the canopy against the mounting strap to see how far you should insert the screws. Tighten nuts (C) onto mounting screws (A)
to hold the screws in place.
2. Pull the house wires through the center of mounting strap (B). Place mounting strap (B) over the junction box so that mounting screws
(A)arevertical,andinalignmentwiththeholelocationsonthexture’scanopy(G).Securemountingstrap(B)tothejunctionboxwith
mounting screws (D) and a screwdriver. Tighten the screws securely.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
5.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothewiring
diagramandattachthexture’swirestothepowersupplywiresfromthejunctionbox.Connect
Hot to Hot, Neutral to Neutral, and Ground to Ground. Twist the ends of the wire pairs together,
and then twist on a wire connector. Make sure all twists are in the same direction. If there is
no house ground wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.Usea
screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/
mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
6.Placethexture’scanopy(G)overmountingscrews(A)sothatmountingscrew(A)protrude
through the holes in canopy (G). Thread deco nuts (H) onto mounting screws (A).
7. Slide shade (O) over socket (N) and twist socket ring (P) onto the threads of socket (N) to
secure the glass in place. (Note: Once installed, adjust shade angle using thumb screws (M).
8.Installlightbulb(Q-notincluded)inaccordancewiththexture’sspecications.Donot
exceed the maximum recommended wattage.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
ASSEMBLING THE FIXTURE
3.Rods(J)and(K)areonthexture’swires.Bymeasuring,determinethecorrectnumber
ofrodsneededforproperhangingheight.*Thisxtureincludes(1)6”rod(J)and(3)12”
rods(K).Toshortenthexture,slidetheexcessrodsoffthewires.Additionalrodsmaybe
purchased.Tolengthenthexture,addadditionalrodstothewires.
4.Pullthexture’swiresthroughrods(Jand/orK)untiltautandthreadtherodstogether.
Thread the bottom rod into post (L). Thread the top rod to the threads of the swivel joint on
canopy (G) and twist thumb screw (I) to lock in place.
I
B
JUNCTION
BOX
D
A
E
C
F
H
G
L
N
M
Q
O
P
J
K
Assembly Instructions