Assembly Instructions

ManualsBrandsCharlton Home ManualsBedroom SetsNorth Adams Queen Platform 5 Piece Bedroom Set

Page 1 of 6

Position :

at bottom of the drawer box

Qty.

Footboard

Descriptions

Headboard Panel

NO.

A 1

Slat Cover

Headboard Leg Left (L)

Headboard Leg Right (R)

Part List Pack In Headboard &

Footboard

Drawer Slat

Drawer Slat Support

Drawer Slat Stopper

Bed Slat 3 Holes

Bed Slat 2 Holes

Bed Slat Support

Side Rail 2

Center Slat With Slat 3 Holes 1

Drawer 2

Hardware List Pack In Headboard

&Footboard

Qty

Descriptions

CSK M4 x 16mm

CSK M4 x 32mm

JCBC Screw M6 x 30mm

JCBC Screw M6 x 50mm

Spring Washer Ø1/4"

Flat Washer Ø1/4" x 13mm

L Key M4

L Key M5

ASSEMBLY INSTRUCTION

QUEEN BED

Summary of content (6 pages)

PAGE 1
ASSEMBLY INSTRUCTION QUEEN BED Part List Pack In Headboard & Footboard NO. A B C D E F G H I J K L M N Descriptions Headboard Panel Headboard Leg Left (L) Headboard Leg Right (R) Footboard Slat Cover Drawer Slat Drawer Slat Support Drawer Slat Stopper Bed Slat 3 Holes Bed Slat 2 Holes Bed Slat Support Side Rail Center Slat With Slat 3 Holes Drawer Qty.
PAGE 2
ASSEMBLY INSTRUCTION QUEEN BED STEP 1.1: Align and fasten Headboard Leg (B) & (C) to Headboard Panel (A) using JCBC M6 x 30mm (1), Spring Washer Ø14"(2) and Flat Washer Ø14" x 13mm (3) and tighten with L Key M4 (7).
PAGE 3
ASSEMBLY INSTRUCTION QUEEN BED STEP 2.1: Attach the Bed Rail (L) to Headboard Leg. STEP 2.2: Tighten SCREW on Headboard Leg by using L KEY M5 (8) & repeat the same step on Footboard (D). STEP 2.3: Move the bed to the desired position. STEP 2.4: Attach the Drawer Slat (F) each to a Drawer Slat Support (G) & fix with Drawer Slat Support Stopper (H). STEP 2.5: Fix the Drawer Slat (F) to Bed Rail (L) with CSK M4 x 32mm (2). STEP 2.6: Move 'T' Runner at Footboard (D) to Drawer Slat (F). L L 8 STEP 2.
PAGE 4
ASSEMBLY INSTRUCTION QUEEN BED STEP 3.1: Insert Drawer (N) to Footboard (D) until completely closed. STEP 3.2: Tighten 'T' Runner at Footboard (D) to Drawer Slat (F) with CSK M4 x 16mm (1). STEP 3.3: If Drawer (N) does not close properly,adjust the adjuster at the bottom of Drawer Slat Support (G) up or down until the Drawer (N) closes tightly. STEP 3.1 N L 1 D Adjuster F 'T' Runner G F H N L STEP 3.2 G N STEP 3.
PAGE 5
ASSEMBLY INSTRUCTION QUEEN BED STEP 4.1: Attach the Center Slat (M), Bed Slat (I)&(H) to Bed Slat Support (K).Tighten with JCBC M6 x 50mm (4) by using L KEY M4 (7). STEP 4.2: Attach Bed Slat (I)&(H) Bed Slat Support (K) and tighten to Bed Rail (L) with CSK M4 x 32mm (2). 2 L 7 STEP 4.2 I J 4 I I &J M M K K STEP 4.
PAGE 6
ASSEMBLY INSTRUCTION QUEEN BED STEP 5.1: Attach the Slat Cover (E) to top Bed Slat (I) & (J) . STEP 5.2: Close the distance Slat Cover (E) to Footboard (D).Tighten Slat Cover (E) to Wood at Footboard (D) with CSK M4 x 16mm (1). 1 E E STEP 5.1 STEP 5.