Lifetime Limited Warranty Our fan motors are warranted to the original purchaser to be free of electrical and/ or mechanical defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to be free from defects in materials or workmanship for a period of 1 year from the date of purchase.
Safety Rules 1 Unpacking Your Fan 2 Installing Your Fan 3 Operating Your Fan 10 Care of Your Fan 11 Troubleshooting 11 Specifications 12 Table of Contents
READ AND SAVE THESE INSTRUCTIONS 1. To reduce the risk of electric shock, insure electricity 2. 3. 4. 5. 6. has been turned off at the circuit breaker or fuse box before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. CAUTION: To reduce the risk of personal injury, use only the screws provided with the electrical box.
1 5 8 a b c d 2 9 6 3 4 7 Unpack your fan and check the contents. You should have the following items: 1. Mounting Bracket (inside canopy) 2. 4.25” Ball/Downrod Assembly (hanger pin and locking pin pre-attached) 3. Canopy 4. Blade Arms (5) 5. 6. 7. 8. 9. Fan Motor Assembly Light Kit Fitter Assembly Blades (5) Glass Shape Light Bulbs (2) a. Mounting hardware (blade attachment screw) b. Electrical hardware & Balancing kit (3 plastic wire connectors, blade balancing kit, plastic plug) c.
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options If there isn’t an existing electrical box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the electrical box directly to the building structure. Use appropriate fasteners and building materials.
Hanging the Fan REMEMBER to turn off the power. Follow the steps below to hang your fan properly. NOTE: This fan is recommended for standard ceiling mount using the downrod provided with this fan. When using standard ceiling installation with the 4.25 inch downrod provided, the distance from the ceiling to the bottom of the fan blades will be approximately 12 inches. Standard Ceiling Mounting 1. Remove the mounting bracket from the canopy by loosening the four screws on the top of the canopy.
Installing Fan to the Electrical Box WHEN MOUNTING THE FAN ON A SLOPED CEILING, THE STANDARD BALL/DOWNROD MOUNTING METHOD MUST BE USED. THE MOUNTING BRACKET MUST BE MOUNTED SO THAT THE SLOT OPENINGS ARE ON THE LOWER SIDE BY SLIDING THE MOUNTING BRACKET FROM THE TOP DOWN. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 7. 2. Install the ceiling mounting bracket on the electrical box by using the mounting screws provided with the electrical box.
Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections. (Figure 9) 1. Connect the two green fan ground wires, located on the downrod and mounting bracket, to the household ground wire. 2. Connect the neutral fan (White) wire to the white neutral household wire. 3.
Finishing the Fan Installation STANDARD CEILING MOUNTING WHEN USING THE STANDARD BALL/DOWNROD MOUNTING, THE TAB IN THE RING AT THE BOTTOM OF THE MOUNTING PLATE MUST REST IN THE GROOVE OF THE HANGER BALL. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. 1. Align the locking slots of the ceiling canopy with the two screws in the mounting bracket. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. 2.
Attaching the Light Kit CAUTION - To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before installing the light kit. 1. Remove and retain the three mounting screws from the switch housing cover of the light kit fitter assembly (Figure 13). Blue Black White Molded Adaptor Plugs White 2. Connect the wires from the switch housing to the wires from the light kit fitter by connecting the molded adaptor plugs together (blue to black, white to white). 3.
Assembling the Fan without the Light Kit 1. In order to use the fan without the light kit , remove the switch box housing from the top of light kit fitter assembly by removing the center hex nut inside the switch box housing, and then thread the switch box housing off the threaded nipple on the top of the light kit fitter assembly (figure 17). Hex nut Switch box cover 2. Press the plastic plug (provided) into the center hole of the switch box housing (figure 18). Switch box Switch box cover 3.
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. The fan shipped from the factory with the reversing switch positioned to circulate air downward. If airflow is desired in the opposite direction, turn your fan off and wait for the blades to stop turning, then slide the reversing switch (located on the switch housing, refer to figure 6 on page 4) to opposite position, and turn fan on again.
Care of Your Fan Troubleshooting 1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) Fan will not start 1. 2. Check main and branch circuit fuses or breakers Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds noisy 1. 2.
FAN SIZE SPEED VOLTS 52” Low High 120 120 FAN POWER CONSUMPTION AIRFLOW (WITHOUT LIGHTS) CFM WATTS 13 65 1970 4474 AIRFLOW EFFICIENCY (HIGHER IS BETTER) CFM/WATT 152 69 NET WEIGHT 16.1 Lbs GROSS CUBE WEIGHT FEET 18.8 Lbs 1.7 All Rights Reserved 12.
Garantía Limitada de por Vida Nuestro los motores de ventilador se garantizan al comprador original como libres de defectos eléctricos y/o mecánicos por el tiempo en que estén en posesión de dicho comprador. Los interruptores activados por cadena, interruptores de reversa, capacitores y acabados en metal se garantizan como libres de defectos materiales o de fabricación por el plazo de 1 año a partir de la fecha de compra.
Normas de seguridad 1 Cómo desempacar el ventilador 2 Cómo instalar el ventilador 3 Cómo usar el ventilador 10 Cuidado del ventilador 11 Solución de problemas 11 Especificaciones 12 Tabla de contenido
LEE Y GUARDA ESTAS INSTRUCCIONES 1. Para disminuir el riesgo de descarga eléctrica, antes de comenzar la instalación asegúrate de que la electricidad ha sido cortada en el cortacircuitos o en la caja de fusibles. 2. Todo el cableado tiene que cumplir con el Código Nacional de Electricidad ANSI/NFPA 70-1999 y con los códigos locales de electricidad. La instalación eléctrica debe hacerse por un electricista calificado con licencia. 3.
1 5 8 a b c d 2 9 6 3 4 7 Desempaca tu ventilador y revisa el contenido. Debes tener los siguientes artículos: 1. Soporte de montaje (dentro de la cubierta) 2. Conjunto de tubo bajante/bola de 4.25" (15.2 cm) (con pasadores de soporte y de cierre prefijados) 3. Cubierta 4. Brazos de aspas (5) 5. 6. 7. 8. 9. Conjunto motor-ventilador Conjunto del soporte del kit de luces Aspas (5) Superficie de vidrio Bombillas (2) a. Herrajes para montaje (tornillos para el montaje de aspas) b.
Herramientas necesarias Las figuras 1, 2 y 3 ejemplifican diferentes maneras de montar la caja eléctrica. Destornillador Phillips o de punta plana, llave ajustable, escalera de tijera y cortacables. Provee un soporte fuerte Placa de montaje en cielo raso Caja eléctrica empotrada Opciones de montaje Figura 3 Si no hay una caja eléctrica presente, lee las siguientes instrucciones. Desconecta la corriente eléctrica retirando los fusibles o apagando los cortacircuitos.
Cómo colgar el ventilador RECUERDA cortar el suministro de electricidad. Sigue los pasos más abajo para colgar correctamente tu ventilador. NOTA: Se recomienda instalar este ventilador en techo interior estándar usando el tubo bajante incluido. Cuando uses una instalación de techo estándar con el tubo bajante de 4.25 pulgadas (10.8 cm) suministrado, la distancia desde el techo a la parte inferior de las aspas será de unas 12 pulgadas (30.48 cm). MONTAJE ESTÁNDAR EN CIELO RASO 1.
Cómo instalar el ventilador en la caja eléctrica PRECAUCIÓN CUANDO MONTES EL VENTILADOR EN UN TECHO INCLINADO, DEBES USAR EL MÉTODO DE MONTAJE CON TUBO BAJANTE-ESFERA ESTÁNDAR. EL SOPORTE DE MONTAJE TIENE QUE INSTALARSE DE MANERA TAL QUE LAS ABERTURAS DE RANURA QUEDEN EN EL LADO INFERIOR, DESLIZANDO EL SOPORTE DE MONTAJE DE ARRIBA ABAJO. 1. Pasa los cables de suministro de 120 voltios a través del orificio central en el soporte de montaje de techo como lo muestra la Figura 7. 2.
1. Conecta los dos cables verdes de conexión a tierra del ventilador, ubicados en el tubo bajante y el soporte de montaje, al cable de conexión a tierra del hogar. 2. Conecta el cable neutro (blanco) del ventilador al cable neutro blanco del circuito eléctrico del hogar. 3. Conecta el cable de alimentación (negro y azul) del ventilador al cable de suministro negro del hogar como se muestra en la Figura 9. 4.
Cómo finalizar la instalación del ventilador MONTAJE ESTÁNDAR EN CIELO RASO ADVERTENCIA EN EL MONTAJE ESTÁNDAR DE TUBO BAJANTE-ESFERA, LA PESTAÑA EN EL ARO DE LA PARTE INFERIOR DE LA PLACA DE MONTAJE TIENE QUE ENCAJAR EN LA RANURA DE LA ESFERA DE SOPORTE. SI NO ENCAJA BIEN LA PESTAÑA EN LA RANURA, PUEDE DAÑARSE EL CABLEADO. 1. Alinea las ranuras de cierre de la cubierta de techo con los dos tornillos del soporte de montaje.
Cómo instalar el kit de luces PRECAUCIÓN – Para disminuir el riesgo de descarga eléctrica, desconecta el circuito de suministro de energía al ventilador antes de instalar el kit de luces. 1. Quita y conserva los tres tornillos de montaje de la cubierta de la caja del interruptor del soporte del kit de luces (Figura 13). 2. Conecta los cables de la caja del interruptor a los cables del soporte del kit de luces, conectando juntos los enchufes con adaptadores moldeados (azul con negro, blanco con blanco). 3.
Cómo ensamblar el ventilador sin el kit de luces Tuerca hexagonal Hex nut Switch de box Cubierta la caja del interruptor cover 1. Para usar el ventilador sin el kit de luces, retira la carcasa de la caja del interruptor de la parte superior del conjunto de soporte del kit de luces, quitando la tuerca hexagonal del centro dentro de la carcasa y desenroscándola de la boquilla en la parte superior del conjunto de soporte del kit de luces (Figura 17).
Las configuraciones de velocidad para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del techo, la cantidad de ventiladores y otras. Este ventilador se envía de fábrica con el interruptor de reversa en posición de circular el aire hacia abajo. Si deseas flujo de aire en sentido contrario, apaga el ventilador y espera a que las aspas se detengan.
Cuidado del ventilador Solución de problemas Aquí tienes algunas sugerencias para dar mantenimiento a tu ventilador. 1. Por causa del movimiento natural del ventilador, algunas conexiones pueden aflojarse. Revisa las conexiones de soporte, los soportes y los accesorios de aspas dos veces al año. Comprueba que estén seguros. (No es necesario desmontar el ventilador del techo). 2. Limpia el ventilador con frecuencia para que luzca como nuevo al paso de los años.
TAMAÑO DEL VENTILADOR 52" (1.32 m) VELOCIDAD VOLTIOS (V) Baja 120 Alta Todos los derechos reservados 120 CONSUMO DE ELECTRICIDAD DEL VENTILADOR (SIN LUCES) VATIOS (W) 13 65 FLUJO DE AIRE CFM EFICIENCIA DE FLUJO DE AIRE (MÁS ALTO ES MEJOR) CFM/W 1970 152 4474 69 PESO NETO PESO BRUTO PIES3 16.1 Lb 18.8 Lb (8.39 kg) 1.7 12.