ASSEMBLY INSTRUCTIONS Installer: Leave these instructions with consumer. 3P us CSA Modeling Consumer: Keep these instructions for future reference. 4\ DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. A WARNING: . Improper installation, adjustment alteration, service or maintenance can cause injury or property damage.
TABLE OF CONTENTS Important Safety Information Information about Propane Specifications‘ Installation Natural Gas Conversion Lighting Instructions Maintenance Batteries Parts L?st Warranty 10
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Tue Gas Code, ANSI 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable. The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).
IMPORTANT SAFETY IN FORMATION ABOUT PROPANE (LP) GAS A serif contained LP-gas cylinder for use with this appliance must have a capacity of 20 Ibs. and must be equipped with a Type.l connector and an OPD (overfill protection device). See Fig. 1. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specification for LP-gas cylinders of the U.S.
INSTALLATION 1. With the help of another person, carefully place the natural stone table top(no include) onto the table base. After making any necessary adjustments to the alignment of the natural stone table top band the top connector bracket, use bolts and washers as shown in Figure 3. Guide the bolt through the top connector bracket into the per-drilled hole on the underside of the natural stone table top. Do not tighten completely. Repeat on other three holes of the top leg connector bracket.
Open the tank door, place the tank in the holder and use the chain to hold the tank. Connect the regulator as shown. in Figure 6. Screw the black handle clock-wise to tighten: Tums the handle counter clock-wise to remove. The hose must point down. Open the control door and check that the valve is turned all the way clockwise to the “OFF” position. Open the tank valve. Apply @ solution of soapy water to the tank-regulator connection and to the valve-hose connection to check for leaks.
NATURAL GAS CONVERSION @ conversion must be performed only by natural gas provider or service company. Natal gas {. Disconnect the gas hose from the gas valve. See Figure 7. Figure 7 2. Disconnect the gas tube from the orifice and remove the orifice holder as shown in Figure 8. Figure 8 ure 9) with the natural gas orifice from the kit and reinstall the 3. Replace the propane orifice (See Fig Figure 10. Reconnect and tighten the gas tube to orifice holder by tightening the nuts as shown in the orifice.
4 . Stick the conversion Label on the rating plate as shown in Figure 11. Metal Rating Plate Serial Number . CAUTION: The sas aureus oscillator provided with this appliance must be used. This initiator is set for an outlet pressure of This appliance has been conversed to use Natural Gas, Input 40,000 Btu/he. Max Gas Supply Pressure 7 inch w.c. (174 kPs) Min. Gas Supply Pressure 5 inch w.e (1.24 kPa) Minimum clearance from combustible constructions: ‘Sides: 24 in.609 rom. Tap 72 fn. 1828 mm.
MAINTENANCE The flames should look like those in Figure 13. To clean the burner, use a soft brush after the burner and lava rocks have cooled completely. Never use a vacuum cleaner on the lava rocks. It is recommended ghat the lava rocks be stored indoors during the winter if they will be subjected to freezing temperatures. The propane cylinder must be discommoded and removed from the appliance before the appliance can be stored indoors. BATTERIES Make sure the control knob is in the “OFF” position.