Installation Guide

ManualsBrandsCharlton Home ManualsLightingHouseholder Speckled Black 1 -Light 21.75'' H Hardwired Lantern Head

Package Contents

Warnings and Cautions

1of2

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

markingpen,1/16”

drillbit,centerpunch,hammer,drillandwrench.

(2)B10CandelabraBaseBulbs60WMaximum,

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses,

CandelabraBaseT8 VintageBulbsarerecommended,bulbsnotincluded.

Mounting Screw

Finial

Glass Panel

Fixture Hood

Fixture Body

STEP 1 Install Glass Panels-

A. Insert the bottom edge of the

Glass Panel (D) into the slot in

the Fixture Body (G) and fold

tabs in the top edge of the

Fixture Body (G) onto the top

edge of the Glass Panel (D) to

secure the Glass Panel (D).

Slot

Tab

Figure 1

STEP 2 - Install Stem, Bulbs and

Fixture Hood

A. Thread the beaded end of the

Stem (F) onto the junction box in

the bottom center of the cage

and hand tighten until snug.

B. Insert bulbs onto sockets and

screw snugly into place.

C. Place the Fixture Hood (E) onto

the top edge of the Fixture Body

(G). Locate the Waterproof

Washer (C) onto the Stem (F)

and thread the Finial (B) onto the

Stem (F) to secure the Fixture

Hood (E). Hand tighten until

snug.

Figure 2

STEP 3 - Mark the Location for the 3 Mounting Holes

A. Place the light fixture onto the post and mark the location of the 3

mounting holes on the fixture fitter onto the post with the marking

pen.

Fixture

Fitter

Marking Pen

Mounting Hole

Post

Lighting

Post

Fixture

Fitter

Figure 3

Waterproof Washer

Stem

Socket

T8 Vintage Bulb

(recommended

but not included)

Junction Box

Installation Guide

Summary of content (2 pages)

PAGE 1
Installation Guide Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/16” drill bit, center punch, hammer, drill and wrench. Light Source: (2) B10 Candelabra Base Bulbs 60W Maximum, Candelabra Base T8 Vintage Bulbs are recommended, bulbs not included. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
STEP 4 - M arking the C enter of E ach M ounting H ole FINISH: SPECKLED BLACK Figure 4 A. Remove the light fixture. Using the center punch and hammer marking the center of each mounting hole location that is marked with the marking pen. Hammer Marking 9.5” 8.25” Center Punch Post STEP 5 - Drill Holes A. Using the 1/16” bit and drill, drill a pilot hole completely through the post at each (3) locations marked in step 4 above. 1/16” bit and drill 21.75” Post Figure 5 STEP 6 - Wire Connections A.