Charnwood, 1 Rowan Street,Leicester, LE3 9GP, England Tel. 0 1 1 6 2 5 1 1550 Fax. 0116 253 2891 email; sales @charnwood.net.
Contents • 1.0 General 1.1 Specifications 1.2 User Responsibility/Warranty 1.3 Final Assembly and Installation 2.0 Settings 2.1 Changing and Setting the Sawblade 2.2 Blade Guiding 2.3 Setting the Cutting Height 2.4 Saw Table Tilt 2.5 2.6 2.7 3.0 4.0 Safety Information Other Information Electrical Installation Electrical Wiring Diagrams Spare Parts List/Exploded View Drawing 1.0 General 1.1 Specifications Dimensions(lxwxh) Weight with motor Table height from floor Throat width Max.
Centering the Table • Loosen the screws holding the lower table trunnion. • Move table sideways as required, until sawblade runs through the centre of the table insert. • Tighten the table trunnion screws, ensure the table stays in its set position Setting the Table Square with the Sawblade • The saw table can be tilted up to 45° .To tilt, loosen the knob of the table trunnion. • A stop on the underside of the table rests on the lower wheel housing when the table is at 90° with the blade.
2.0 Band Saw Settings 2.1 C h a n g i n g a n d Setting the S a w B l a d e This band sawis factoryequipped with a general purpose woodcutting blade, the blade set. To change the blade, remove the rip fence carrier extrusion from the table. Then slacken the blade tension by turning the-handwheel on top of the upper wheel housing. Remove the blade. Fit new blade and tension lightly. The blade should run in the centre of the rubber lined band saw wheels or else ir may jump of.
2.5 Safety Information 1. Check that all guards are in place and securely locked before switching the machine on. 2. Always disconnect from power when servicing this machine. 3. Do not use bent or cracked band saw blades. 4. Replace table insert if slot has enlarged. 5. For cutting operations with a tilted table the rip fence has to be located to the right hand side of the blade. 6. When cutting round stock use a suitable jig or fixture to keep the work from turning. 7.
Cedar Court, Walker Rd Bardon Hill, Leicestershire LE671TU ENGLAND
-6-
PARTS LIST Item Part No. 1 31503031 2 31503022 3 31503032 4 31503020 5 DJ250B04001 6 31503033 7 31503030 8 GB862.2-87 6 9 GB5783-86 M6xl0 10 DJ250B03001 11 DJ250A05001 12 GB894.1-86 10 13 GB/T276-94 6000-2Z 14 DJ250A03005 15 DJ250A03005-1 16 DJ250A04009 17 DJ250A03004A 18 GB896-86 19 DJ250A03007 20 DJ250A03003A 21 GB6177-86 M6 22 DJ250A03002A 23 GB819-85 M4xl2 24 KJD20 25 DJ25005004B 26 GB862.
PARTS LIST Item 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 Part No.
PARTS LIST Item Part No. Description 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 DJ250A03012 DJ315B03031-1 GB845-85 ST4.2x9.5 DJ250A03018 DJ250A03013 DJ315B03016 GB889-86 M8 GB818-85 M5xl0 DJ250A04005 DJ25004008 DJ25004010 GB1096-79 5x30 DJ25004004 GB14-88 M6xl6 GB6171-86 M14xl.5 GB93-87 14 DJ250A04006 GB93-87 6 DJ25005003-1 YYL7114 Guide Lever Cover Board Cross Pan.Hd.Screw Rack Guide Piece Adjust Knob Hx.Hd.Lock Nut Cross Pan. Hd.