User Manual
TABLE OF CONTENTS 1. Before You Begin .......................................................................................................... 3 What Is Included ............................................................................................................................. 3 Unpacking Instructions .................................................................................................................... 3 Claims........................................................................
1. BEFORE YOU BEGIN What Is Included • • • BOB LED Hanging Chain Table/Floor Mounting Legs • • • Connecting Hardware Warranty Card Quick Reference Guide Unpacking Instructions Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. Claims If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet.
Product at a Glance Use on Dimmer Outdoor Use Sound-Active DMX Master/Slave Safety Notes Auto Programs Auto-ranging Power Supply Replaceable Fuse User-Serviceable x x P x Please read the following Safety Notes carefully before working with the product. The Notes include important safety information about installation, usage, and maintenance. • • • • • • • • • • • • • • • • • • • • • Page 4 of 15 x x x x x Always connect the product to a grounded circuit to avoid the risk of electrocution.
2. INTRODUCTION Product Overview Air Vents Mounting Legs x 3 Front View Chain Attachment Holes x 3 Silk Attachment Plates x 2 Top View BOB LED User Manual Rev.
Product Overview Cont. Magnetic Strips Silk Flame Attachment Hanging Loop Attachment Loops Hanging Chain For illustrative purposes. Your product may differ slighting from the diagrams shown. Page 6 of 15 BOB LED User Manual Rev.
Product Dimensions 17.5 in 445 mm 11 in 279 mm 27 in 686 mm 5.5 in 140 mm 12.5 in 318 mm 17.5 in 445 mm BOB LED User Manual Rev.
3. SETUP AC Power The BOB LED has a fixed power supply and it can work with an input voltage of 120 VAC, 60 Hz or 230 VAC, 50Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The BOB LED may be used with the chain suspensions or with the 3 table/floor mounting legs that are provided with the fixture. Make sure there is adequate room for ventilation when mounting this product. Rigging Floor Mounting Diagram • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance purposes.
1 Hanging Mounting Diagram 2 3 1 2 3 Attach all 3 chain sections to the chain attachment holes on flame base. Be sure the silk flame is clear of the chain while hanging and during operation. Page 10 of 15 BOB LED User Manual Rev.
4. OPERATION Silk Flame Attachment Attach each magnetic strip on the simulated silk flame to a silk attachment plate on the base. Be careful not to damage the silk. A B A B Be sure the silk is free from the air vents on the base, before powering on or walking away. Configuration (Standalone) BOB LED User Manual Rev. 5 This product is intentionally meant to be controlled without a DMX controller. It will stay on, as long as it is plugged in. To use this product; 1.
5. MAINTENANCE Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency. To clean the product, follow the instructions below: 1. Unplug the product from power. 2.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight with Legs Length Width Height Weight 17.5 in (445 mm) 17.5 in (445 mm) 30.5 in (775 mm) 5.1 lb (2.3 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Dimensions and Weight with Chains Length Width Height Weight 11 in (280 mm) 11 in (280 mm) 29 in (737 mm) 4.8 lb (2.2 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Light Source Photometrics Thermal Ordering BOB LED User Manual Rev.
RETURNS In case you need to get support or return a product: • If you are located in the U.S., contact Chauvet World Headquarters. • If you are located in the UK or Ireland, contact Chauvet Europe Ltd. • If you are located in Mexico, contact Chauvet Mexico. • If you are located in Benelux, contact Chauvet Europe BVBA. • If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local distributor. See www.chauvetlighting.com for distributors outside the U.S.
CONTACT US USA WORLD HEADQUARTERS General Information Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: (954) 577-4455 Fax: (954) 929-5560 Toll free: (800) 762-1084 Technical Support Voice: (954) 577-4455 (Press 4) Fax: (954) 756-8015 Email: tech@chauvetlighting.com World Wide Web www.chauvetlighting.