User Manual
Edition Notes Edition Notes The Legend™ 1200E Spot User Manual Rev. 03c covers the description, safety precautions, installation, programming, operation, and maintenance of the Legend™ 1200E Spot product. CHAUVET® released this edition of the Legend™ 1200E Spot User Manual Rev. 03c in October 2010. Trademarks CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or Chauvet).
Table of Contents Table of Contents 1. Before You Begin ............................................................................................................1 What is Included ............................................................................................................................. 1 Unpacking Instructions ................................................................................................................... 1 Typographic Conventions ...................................
Table of Contents 5. Technical Information ................................................................................................... 27 General Maintenance.................................................................................................................... 27 Dust Screen Cleaning .............................................................................................................................. 27 Error Messages ............................................................
Before You Begin 1. Before You Begin What is Included Unpacking Instructions • One Legend™ 1200E Spot • Two omega brackets • Two hanging trigger clamps • One flight case • Warranty Card • Quick Reference Guide This product ships in a flight case. Immediately upon receiving this product, carefully unpack it and check the container in which you received it. Make sure that you have received all the parts indicated above and that they are all in good condition.
Before You Begin Safety Notes Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. It is important to read all these notes before starting to work with this product. There are no user serviceable parts inside this product. Any reference to servicing it you may find from now on in this User Manual will only apply to properly CHAUVET® certified technicians.
Introduction 2. Introduction Product Description The Legend™ 1200E Spot is a moving yoke fixture with a 1200 W short arc discharge lamp. It contains an LCD control panel (display), through which all of the settings can be set or modified. This fixture can operate at 200~240 VAC, 50/60 Hz, which eliminates the need for a voltage selection switch. The ballast and igniter in the lamp circuit are both of the electronic type. Features • • 23 or 31-channel DMX moving yoke Pan 540⁰ in 2.
Introduction DMX Channel Summary -4- 31-Channel Mode 23-Channel Mode Channel Channel Function Function 1 Pan 1 Pan 2 Pan fine 2 Pan fine 3 Tilt 3 Tilt 4 Tilt fine 4 Tilt fine 5 Pan/tilt speed 5 Pan/tilt speed 6 Dimmer 6 Dimmer 7 Dimmer fine 7 Shutter 8 Shutter 8 Color 9 Color 9 Cyan 10 Cyan 10 Magenta 11 Magenta 11 Yellow 12 Yellow 12 3,200 K (CTO) Filter 13 3,200 K (CTO) 13 Gobo 1 14 CMY/CTO Filter Speed 14 Gobo 1 rotation 15 Gobo 1 15 Gob
Introduction Product Overview Liquid Crystal Display Jog Wheel ENTER button Power LED indicator MENU button DMX LED indicator DMX in (3-pin) POWER button DMX out (3-pin) Fuse holder (Main) Fuse holder (Lamp) DMX out (5-pin) Power input DMX in (5-pin) Tilt lock Pan lock Control panel Legend™ 1200E Spot User Manual Rev.
Introduction Product Dimensions -6- Legend™ 1200E Spot User Manual Rev.
Setup 3. Setup AC Power The Legend™ 1200E Spot has an auto-ranging power supply that can work with an input voltage range of 200~240 VAC, 50/60 Hz. Make sure that you are connecting this product to the proper voltage, as per the specifications in this guide, the product’s user manual, or on the product’s sticker. Always connect the Legend™ 1200E Spot to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire.
Setup Mounting Before mounting this fixture, read and follow the safety recommendations indicated in the Safety Notes section (page 2 of this manual). Orientation Always mount this fixture in any safe position while making sure that there is adequate room around it for ventilation, configuration, and maintenance. Make sure to mount this fixture away from any flammable material as indicated in the Safety Notes section. Rigging The Legend™ 1200E Spot comes with two omega brackets and two clamps.
Setup Bracket Installation You can mount the included brackets on either side of the mounting plate. This allows for positioning the fixture’s base in the best possible orientation to access the control panel and the fuses. Control Panel Bracket Mounting Diagram Location 1 Location 2 Optics The Legend 1200E Spot has one color wheel with seven colors and two gobo wheels that support six rotating, slot-n-lock gobos each. The colors in the color wheel are not replaceable, but the gobos are.
Setup Gobo Wheels The diagram below shows both gobo wheels and the number assigned to each gobo on each wheel. Rotating Gobo Wheel 1 5 6 4 3 1 2 Rotating Gobo Wheel 2 11 12 10 9 7 8 -10- Legend™ 1200E Spot User Manual Rev.
Setup Replacing Gobos The gobos in the Legend 1200E Spot’s gobo wheels are removable from their gobo plates. This operation is quite simple, although it requires the technician to be careful and to follow the recommended procedure. • Make sure to disconnect the fixture’s power cord before replacing a gobo. • Always replace a gobo with a gobo of the same dimensions. • When inserting a glass gobo, always make sure that the shinny side of the gobo (glass base) faces the lamp.
Setup Lamp Replacement The Legend 1200E Spot is equipped with a Phillips MSR1200SA/SE FastFit lamp. This lamp uses a socket that allows for fast and easy lamp changes. Follow the procedure below to safely change the Legend 1200E Spot’s lamp. Never touch the lamp’s envelope (glass bulb) with your bare hands. FastFit lamps do not require touching the lamp’s envelope during removal or installation.
Operation 4. Operation Button Control Panel Description Function
Operation Menu Map nd Main Menu Level 2 Level DMX Address DMX Channel Mode DMX Functions rd 3 Level th 4 Level 1~512 Mode 1 (23) Mode 2 (31) View DMX Value N/A WDMX Setting (Requires optional W-DMX card) Active Retransmit N/A No/Yes Reset Memory Pan Inverse Tilt Inverse Fixture Settings Bl.o. P/T Moving Bl.o. Color Change No/Yes N/A Bl.o.
Operation Programming Carry out all the programming procedures indicated below from the control panel. Refer to the Menu Map page to learn how the menu options relate to each other. Navigation Control The Control Panel’s liquid crystal display (LCD) shows the menu items you select. When you select a menu function, the display will show the available options for the selected function with the first one already highlighted. If not at the home screen, press
Operation Continued from previous page Tilt Reversal This option reverses the tilt angle assignments from 000 = 0º and 255 = 270º to 000 = 270º and 255 = 0º. 1) Select Tilt Inverse. 2) Select Yes (reversed assignments) or No (normal assignments). 3) Press . Blackout During Head Motion This option enables the blackout feature while the fixture head is moving (panning or tilting). 1) Select Bl.o. P/T Moving. 2) Select Yes (blackout enabled) or No (blackout disabled). 3) Press .
Operation Continued from previous page Lamp Off When DMX is Absent When enabled (Yes), this option turns the lamp off when DMX signal is absent. 1) Select Off if DMX Off. 2) Select Yes or No 3) Press . Cooling Mode This option determines the speed of the cooling fans, whether always high or automatic. 1) Select Cooling Mode. 2) Select High or Auto. 3) Press . Ignition Delay When the State/Power On option is active, this setting configures the delay before the lamp strikes after power on.
Operation Continued from previous page Fixture Tests The options in the Lamp Settings section control what tests the fixture will run. To access this section, do the following: 1) Press
Operation Continued from previous page Pan & Tilt This option resets the pan and tilt of the fixture’s head to their corresponding home positions. 1) Select Pan & Tilt. 2) Select Yes (reset) or No (exit without resetting). 2) Press . The fixture’s will move to the pan and tilt home positions. Color This option resets the color wheel to its corresponding home position. 1) Select Color. 2) Select Yes (reset) or No (exit without resetting). 2) Press .
Operation Continued from previous page Factory Default If you want to default the fixture to its factory configuration, follow the following steps: 1) Select Factory Settings. 3) Select Yes (default fixture) or No (exit without defaulting). 4) Press . • The above operation will default all the fixture’s parameters to their original factory configuration values. • Defaulting the fixture does not affect the home position settings.
Operation Continued from previous page R-Gobo 1 Motor 1) Select R-Gobo 1 and press . a) Select the new value (-128~127). b) Accept the new value. Gobo 2 Motor 1) Select Gobo 2 and press . a) Select the new value (-128~127). b) Accept the new value. R-Gobo 2 Motor 1) Select R-Gobo 2 and press . a) Select the new value (-128~127). b) Accept the new value. Iris Motor 1) Select Iris and press . a) Select the new value (0~255). b) Accept the new value.
Operation DMX Values Mode 1 (Basic) Channel Function Value 1 2 3 4 5 6 Pan Pan Fine Tilt Tilt Fine Pan/Tilt Speed Dimmer 7 Shutter 8 Color 9 10 11 12 Cyan Magenta Yellow 3200 K Filter 13 Gobo 1 14 R-Gobo 1 15 Gobo 2 000 000 000 000 000 000 000 008 016 132 168 204 240 000 008 016 024 032 040 048 056 064 128 190 194 000 000 000 000 000 010 020 029 039 048 058 068 078 088 098 108 118 128 190 194 000 12
Operation Continued from previous page Mode 1 (Cont.) Channel Function 15 Gobo 2 (Cont.
Operation Mode 2 (Advanced) Channel Function Value 1 2 3 4 5 6 7 Pan Pan fine Tilt Tilt fine Pan/tilt Speed Dimmer Dimmer fine 8 Shutter 9 Color 10 11 12 13 14 Cyan Magenta Yellow 3200 K Filter Filters Speed 15 Gobo 1 16 R-Gobo 1 17 R-Gobo 1 Fine 18 Gobo 2 000 000 000 000 000 000 000 000 008 016 132 168 204 240 000 008 016 024 032 040 048 056 064 128 190 194 000 000 000 000 000 000 010 020 029 039 048 058 068 0
Operation Continued from previous page Mode 2 (Cont.) Channel Function Value 18 Gobo 2 (Cont.
Operation Continued from previous page Mode 2 (Cont.
Technical Information 5. Technical Information General Maintenance To maintain optimum performance and minimize wear, the user should clean the light fixtures frequently. Usage and environment are contributing factors in determining the cleaning frequency. As a rule, the user should clean the fixtures at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear.
Technical Information Error Messages Message Cause(s) Action(s) Lamp Startup Fail The lamp has not started after being struck. • • • Check lamp Check lamp socket and wiring Check ballast and igniter Temperature Sense Fail There is no communication with temperature sensor. • • • Check sensor wiring Check sensor integrity Check control board Lamp Hot Protection Fixture temperature is higher than 105º C; • lamp was switched to low power for safety.
Technical Information Troubleshooting Guide Symptom Fixture does not power up Fixture powers up but lamp does not ignite Lamp ignited but has low intensity/color temperature Lamp flickers or turns off by itself Circuit breaker/fuse keeps tripping/blowing Fixture does not respond to DMX when nearby fixtures on the same universe do Cause(s) Action(s) • No power on outlet • Repair outlet problem or use another outlet • Blown fuse • Replace blown fuse with same type and rating fuse • Bad powe
Technical Information Returns Procedure The user must send the merchandise prepaid, in the original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Call CHAUVET® and request a Return Merchandise Authorization Number (RMA #) before shipping the fixture. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. The user must clearly label the package with a Return Merchandise Authorization Number (RMA #).
Technical Information Technical Specifications Dimensions and Weight Fixture Only Fixture in Flight Case Power Length Width Height Weight 20.5 in (521 mm) 21.2 in (539 mm) 30.1 in (764 mm) 82.05 lbs (37.22 kg) Length Width Height Weight 25 in (635 mm) 28 in (711 mm) 35 in (889 mm) 191.05 lbs (86.22 kg) Power Supply Type Range Voltage Selection Switching (w/PF correction) 100~240 V, 50/60 Hz Auto-ranging Parameter 208 V, 60 Hz 230 V, 50 Hz Consumption 1,641 W (7.
CHAUVET® 5200 NW 108th Avenue Sunrise, FL 33351 (USA) (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.com Legend™ 1200E Spot User Manual Rev.