User Manual
TABLE OF CONTENTS 1. Before You Begin .......................................................................................................... 3 What Is Included ............................................................................................................................... 3 Unpacking Instructions ..................................................................................................................... 3 Claims ....................................................................
1. BEFORE YOU BEGIN What Is Included • • • • • BEAMshot™ 4-pack of Gels Power Cord Warranty Card Quick Reference Guide Unpacking Instructions Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition. Claims If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Product at a Glance Use on Dimmer Outdoor Use Sound-Active DMX Master/Slave Safety Notes Auto Programs Auto-ranging Power Supply Replaceable Fuse User-Serviceable Duty Cycle P P P x x These notes include important information about the mounting, usage, and maintenance of this product; read before using the product. • • • • • • • • • • • • • • • • • • • • Page 4 of 17 x x P P P Always connect the product to a grounded circuit to avoid the risk of electrocution.
2. INTRODUCTION Overview Power Out Display Menu Buttons Power In DMX In DMX Out Fuse Holder Back Panel View BEAMshot™ User Manual (Rev.
Dimensions Page 6 of 17 BEAMshot™ User Manual (Rev.
3. SETUP AC Power The BEAMshot™ has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Power Linking The product provides power linking via the Edison/IEC outlet located in the back of the unit. st Power Linking Diagram 1 Product nd 2 Product rd 3 Product Additional Products You can power link up to 62 BEAMshot™ units on 120 VAC or up to 100 BEAMshot™ units on 230 VAC.
Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The BEAMshot™ may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons surrounding the display.
DMX Channel Modes, Assignments, and Values 4-Channel 2-Channel Channel Function 1 White 2 Shutter 3 Auto Programs 4 Speed Channel Function 1 White 2 Shutter BEAMshot™ User Manual (Rev.
Configuration (Standalone) Set the product in one of the standalone modes to control without a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. Never connect a product that is operating in any standalone mode (either Static, Automatic, or Sound) to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.
Master/Slave Mode The Master/Slave mode allows a single BEAMshot™ unit (the “master”) to control the actions of one or more BEAMshot™ units (the “slaves”) without the need of a DMX controller. The master unit will be set to operate in either Automatic or Sound-Active mode, while the slave units will be set to operate at DMX address d 1. Once set and connected, the slave units will operate in unison with the master unit. Configure the units as indicated below. Slave units: 1. Set the DMX address to d 1.
Custom Settings Dimmer Page 14 of 17 The BEAMshot™ allows you to choose custom strobe and dimmer settings to achieve the effect you like. To select these custom settings, follow the instructions below: 1. Press
5. TECHNICAL INFORMATION Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, clean the product at least twice a month. However, usage and environmental conditions contribute to increased cleaning frequency. To clean the product, follow the instructions below: • Unplug the product from power.
6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length Width Height Weight 8.3 in (210 mm) 5.7 in (145 mm) 4.1 in (105 mm) 1.4 lbs (0.7 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Light Source Photo Optic Thermal DMX Ordering Page 16 of 17 Power Supply Type Range Voltage Selection Switching (internal) 100~240 V, 50/60 Hz Auto-ranging Parameter 120 V, 60 Hz 230 V, 50 Hz Consumption 15 W 19 W Operating current 0.1 A 0.
To return a product or request support: • • • In the U.S., contact CHAUVET® World Headquarters (see below). In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below). In any other country, DO NOT contact CHAUVET®. Contact your distributor. See www.chauvetlighting.com for distributors outside the U.S., United Kingdom, or Ireland. If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of record and follow their instructions on how to return CHAUVET® products to them.
